Age | Commit message (Collapse) | Author | Files | Lines |
|
When you cancel an in-progress 'mirror' job (or "active `block-commit`")
with QMP `block-job-cancel`, it emits the event: BLOCK_JOB_CANCELLED.
However, when `block-job-cancel` is issued *after* `drive-mirror` has
indicated (via the event BLOCK_JOB_READY) that the source and
destination have reached synchronization:
[...] # Snip `drive-mirror` invocation & outputs
{
"execute":"block-job-cancel",
"arguments":{
"device":"virtio0"
}
}
{"return": {}}
It (`block-job-cancel`) will counterintuitively emit the event
'BLOCK_JOB_COMPLETED':
{
"timestamp":{
"seconds":1510678024,
"microseconds":526240
},
"event":"BLOCK_JOB_COMPLETED",
"data":{
"device":"virtio0",
"len":41126400,
"offset":41126400,
"speed":0,
"type":"mirror"
}
}
But this is expected behaviour, where the _COMPLETED event indicates
that synchronization has successfully ended (and the destination now has
a point-in-time copy, which is at the time of cancel).
So add a small note to this effect in 'block-core.json'. While at it,
also update the "Live disk synchronization -- drive-mirror and
blockdev-mirror" section in 'live-block-operations.rst'.
(Thanks: Max Reitz for reminding me of this caveat on IRC.)
Signed-off-by: Kashyap Chamarthy <kchamart@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
When doing a live migration of a Xen guest with libxl, the images for
block devices are locked by the original QEMU process, and this prevent
the QEMU at the destination to take the lock and the migration fail.
>From QEMU point of view, once the RAM of a domain is migrated, there is
two QMP commands, "stop" then "xen-save-devices-state", at which point a
new QEMU is spawned at the destination.
Release locks in "xen-save-devices-state" so the destination can takes
them, if it's a live migration.
This patch add the "live" parameter to "xen-save-devices-state" which
default to true so older version of libxenlight can work with newer
version of QEMU.
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20171114180128.17076-2-mreitz@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
|
|
bdrv_set_read_only() is used by some block drivers to override the
read-only option given by the user. This is not how read-only images
generally work in QEMU: Instead of second guessing what the user really
meant (which currently includes making an image read-only even if the
user didn't only use the default, but explicitly said read-only=off), we
should error out if we can't provide what the user requested.
This adds deprecation warnings to all callers of bdrv_set_read_only() so
that the behaviour can be corrected after the usual deprecation period.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Right now it is a variable in MigrationState instead of a
MigrationParameter. The change allows to set it as the rest of the
Migration parameters, from the command line, with
query_migration_paramters, set_migrate_parameters, etc.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
into staging
migration/next for 20171023
# gpg: Signature made Mon 23 Oct 2017 17:05:14 BST
# gpg: using RSA key 0xF487EF185872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
# Primary key fingerprint: 1899 FF8E DEBF 58CC EE03 4B82 F487 EF18 5872 D723
* remotes/juanquintela/tags/migration/20171023: (21 commits)
migration: Improve migration thread error handling
qapi: Fix grammar in x-multifd-page-count descriptions
migration: add bitmap for received page
migration: introduce qemu_ufd_copy_ioctl helper
migration: postcopy_place_page factoring out
migration: new ram_init_bitmaps()
migration: clean up xbzrle cache init/destroy
migration: provide ram_state_cleanup
migration: provide ram_state_init()
migration: pause-before-switchover for postcopy
migration: allow cancel to unpause
migrate: HMP migate_continue
migration: migrate-continue
migration: Wait for semaphore before completing migration
migration: Add 'pre-switchover' and 'device' statuses
migration: Add 'pause-before-switchover' capability
migration: Make cache_init() take an error parameter
migration: Move xbzrle cache resize error handling to xbzrle_cache_resize
migration: Make cache size elements use the right types
migratiom: Remove max_item_age parameter
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Reported-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
A new qmp command allows the caller to continue from a given
paused state.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Add two statuses for use when the 'pause-before-switchover'
capability is enabled.
'pre-switchover' is the state that we wait in for management
to allow us to continue.
'device' is the state we enter while serialising the devices
after management gives us the OK.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
When 'pause-before-switchover' is enabled, the outgoing migration
will pause before invalidating the block devices and serializing
the device state.
At this point the management layer gets the chance to clean up any
device jobs or other device users before the migration completes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
The 'sysrq' key was mistakenly added to QEMU to deal with incorrect handling
of the 'print' key in the ps2 device:
commit f2289cb6924afc97b2a75d21bfc9217024d11741
Author: balrog <balrog@c046a42c-6fe2-441c-8c8c-71466251a162>
Date: Wed Jun 4 10:14:16 2008 +0000
Add sysrq to key names known by "sendkey".
Adding sysrq keycode to the table enabling running sysrq debugging in
the guest via the monitor sendkey command, like:
(qemu) sendkey alt-sysrq-t
Tested on x86-64 target and Linux guest.
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
The ps2 device is now fixed wrt modifiers and the 'print' key. Further the
handling of the 'sysrq' key has some problems of its own, documented in the
previous commit. To cleanup this mess, we convert any use of 'sysrq' into
'print' prior to dispatching the event to device models.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20171019142848.572-9-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
This change introduces a new TPM backend driver that can communicate with
swtpm(software TPM emulator) using unix domain socket interface. QEMU talks to
the TPM emulator using QEMU's socket-based chardev backend device.
Swtpm uses two Unix sockets for communications, one for plain TPM commands and
responses, and one for out-of-band control messages. QEMU passes the data
socket to be used over the control channel.
The swtpm and associated tools can be found here:
https://github.com/stefanberger/swtpm
The swtpm's control channel protocol specification can be found here:
https://github.com/stefanberger/swtpm/wiki/Control-Channel-Specification
Usage:
# setup TPM state directory
mkdir /tmp/mytpm
chown -R tss:root /tmp/mytpm
/usr/bin/swtpm_setup --tpm-state /tmp/mytpm --createek
# Ask qemu to use TPM emulator with given tpm state directory
qemu-system-x86_64 \
[...] \
-chardev socket,id=chrtpm,path=/tmp/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis,tpmdev=tpm0 \
[...]
Signed-off-by: Amarnath Valluri <amarnath.valluri@intel.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
|
|
Make it possible to inject errors on writes performed during a
read operation due to copy-on-read semantics.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
The new name is WatchdogAction which is shorter,
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <dbd61a0928821348486d0d6260be2bd3b02b6402.1504771369.git.mprivozn@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
This patch add shrinking of the image file for qcow2. As a result, this allows
us to reduce the virtual image size and free up space on the disk without
copying the image. Image can be fragmented and shrink is done by punching holes
in the image file.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20170918124230.8152-4-pbutsykin@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
|
|
* Speed up AddressSpaceDispatch creation (Alexey)
* Fix kvm.c assert (David)
* Memory fixes and further speedup (me)
* Persistent reservation manager infrastructure (me)
* virtio-serial: add enable_backend callback (Pavel)
* chardev GMainContext fixes (Peter)
# gpg: Signature made Fri 22 Sep 2017 20:07:33 BST
# gpg: using RSA key 0xBFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (32 commits)
chardev: remove context in chr_update_read_handler
chardev: use per-dev context for io_add_watch_poll
chardev: add Chardev.gcontext field
chardev: new qemu_chr_be_update_read_handlers()
scsi: add persistent reservation manager using qemu-pr-helper
scsi: add multipath support to qemu-pr-helper
scsi: build qemu-pr-helper
scsi, file-posix: add support for persistent reservation management
memory: Share special empty FlatView
memory: seek FlatView sharing candidates among children subregions
memory: trace FlatView creation and destruction
memory: Create FlatView directly
memory: Get rid of address_space_init_shareable
memory: Rework "info mtree" to print flat views and dispatch trees
memory: Do not allocate FlatView in address_space_init
memory: Share FlatView's and dispatch trees between address spaces
memory: Move address_space_update_ioeventfds
memory: Alloc dispatch tree where topology is generared
memory: Store physical root MR in FlatView
memory: Rename mem_begin/mem_commit/mem_add helpers
...
# Conflicts:
# configure
|
|
Indicates how many pages we are going to send in each batch to a multifd
thread.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
--
Be consistent with defaults and documentation
Use new DEFINE_PROP_*
Rename x-multifd-group to x-multifd-page-count
|
|
Indicates the number of channels that we will create. By default we
create 2 channels.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
--
Catch inconsistent defaults (eric).
Improve comment stating that number of threads is the same than number
of sockets
Use new DEFIN_PROP_*
Rename x-multifd-threads to x-multifd-threads
|
|
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
--
Use new DEFINE_PROP
|
|
It is a common requirement for virtual machine to send persistent
reservations, but this currently requires either running QEMU with
CAP_SYS_RAWIO, or using out-of-tree patches that let an unprivileged
QEMU bypass Linux's filter on SG_IO commands.
As an alternative mechanism, the next patches will introduce a
privileged helper to run persistent reservation commands without
expanding QEMU's attack surface unnecessarily.
The helper is invoked through a "pr-manager" QOM object, to which
file-posix.c passes SG_IO requests for PERSISTENT RESERVE OUT and
PERSISTENT RESERVE IN commands. For example:
$ qemu-system-x86_64
-device virtio-scsi \
-object pr-manager-helper,id=helper0,path=/var/run/qemu-pr-helper.sock
-drive if=none,id=hd,driver=raw,file.filename=/dev/sdb,file.pr-manager=helper0
-device scsi-block,drive=hd
or:
$ qemu-system-x86_64
-device virtio-scsi \
-object pr-manager-helper,id=helper0,path=/var/run/qemu-pr-helper.sock
-blockdev node-name=hd,driver=raw,file.driver=host_device,file.filename=/dev/sdb,file.pr-manager=helper0
-device scsi-block,drive=hd
Multiple pr-manager implementations are conceivable and possible, though
only one is implemented right now. For example, a pr-manager could:
- talk directly to the multipath daemon from a privileged QEMU
(i.e. QEMU links to libmpathpersist); this makes reservation work
properly with multipath, but still requires CAP_SYS_RAWIO
- use the Linux IOC_PR_* ioctls (they require CAP_SYS_ADMIN though)
- more interestingly, implement reservations directly in QEMU
through file system locks or a shared database (e.g. sqlite)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
block/throttle.c uses existing I/O throttle infrastructure inside a
block filter driver. I/O operations are intercepted in the filter's
read/write coroutines, and referred to block/throttle-groups.c
The driver can be used with the syntax
-drive driver=throttle,file.filename=foo.qcow2,throttle-group=bar
which registers the throttle filter node with the ThrottleGroup 'bar'. The
given group must be created beforehand with object-add or -object.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
ThrottleGroup is converted to an object. This will allow the future
throttle block filter drive easy creation and configuration of throttle
groups in QMP and cli.
A new QAPI struct, ThrottleLimits, is introduced to provide a shared
struct for all throttle configuration needs in QMP.
ThrottleGroups can be created via CLI as
-object throttle-group,id=foo,x-iops-total=100,x-..
where x-* are individual limit properties. Since we can't add non-scalar
properties in -object this interface must be used instead. However,
setting these properties must be disabled after initialization because
certain combinations of limits are forbidden and thus configuration
changes should be done in one transaction. The individual properties
will go away when support for non-scalar values in CLI is implemented
and thus are marked as experimental.
ThrottleGroup also has a `limits` property that uses the ThrottleLimits
struct. It can be used to create ThrottleGroups or set the
configuration in existing groups as follows:
{ "execute": "object-add",
"arguments": {
"qom-type": "throttle-group",
"id": "foo",
"props" : {
"limits": {
"iops-total": 100
}
}
}
}
{ "execute" : "qom-set",
"arguments" : {
"path" : "foo",
"property" : "limits",
"value" : {
"iops-total" : 99
}
}
}
This also means a group's configuration can be fetched with qom-get.
Signed-off-by: Manos Pitsidianakis <el13635@mail.ntua.gr>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Currently, a FOO_lookup is an array of strings terminated by a NULL
sentinel.
A future patch will generate enums with "holes". NULL-termination
will cease to work then.
To prepare for that, store the length in the FOO_lookup by wrapping it
in a struct and adding a member for the length.
The sentinel will be dropped next.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20170822132255.23945-13-marcandre.lureau@redhat.com>
[Basically redone]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-16-git-send-email-armbru@redhat.com>
[Rebased]
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-15-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-14-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
The next commit will put it to use. May look pointless now, but we're
going to change the FOO_lookup's type, and then it'll help.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-13-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-11-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
The lookup tables have a sentinel, no need to make callers pass their
size.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503564371-26090-3-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Rebased, commit message corrected]
|
|
The generated QEMU QMP reference is now structured as follows:
1.1 Introduction
1.2 Stability Considerations
1.3 Common data types
1.4 Socket data types
1.5 VM run state
1.6 Cryptography
1.7 Block devices
1.7.1 Block core (VM unrelated)
1.7.2 QAPI block definitions (vm unrelated)
1.8 Character devices
1.9 Net devices
1.10 Rocker switch device
1.11 TPM (trusted platform module) devices
1.12 Remote desktop
1.12.1 Spice
1.12.2 VNC
1.13 Input
1.14 Migration
1.15 Transactions
1.16 Tracing
1.17 QMP introspection
1.18 Miscellanea
Section "1.18 Miscellanea" is still too big: it documents 134 symbols.
Section "1.7.1 Block core (VM unrelated)" is also rather big: 128
symbols. All the others are of reasonable size.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-17-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
query-version and query-commands are in common.json for no good
reason. Several similar queries are in qapi-schema.json. Move them
there.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-16-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Except for block-core.json, the sub-schemas are self-contained: if
they use a symbol defined in another sub-schema, they include that
sub-schema. To check, feed the sub-schema to qapi2texi (or any other
QAPI generator) along with the pragma from qapi-schema.json.
Fix up things to make block-core.json self-contained, too.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-15-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-14-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Cc: Alberto Garcia <berto@igalia.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-13-git-send-email-armbru@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Sadly, we don't have a TPM maintainer, not even a MAINTAINERS entry.
Create one, and mark it orphaned.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-12-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-11-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-10-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
UI stuff is remote desktop stuff (Spice, VNC) and input stuff (mouse,
keyboard).
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-9-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-8-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-7-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-6-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Cc: "Daniel P. Berrange" <berrange@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1503602048-12268-5-git-send-email-armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
Bug: introspection documentation is in section "Tracing commands".
Cause: sub-schema qapi/introspect.json lacks a section header, and
therefore goes into whatever section precedes its include.
Fix: add a section header.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1503602048-12268-3-git-send-email-armbru@redhat.com>
|
|
With the move of some docs to docs/interop on ac06724a71,
a couple of references were not updated.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Block layer patches for 2.10.0-rc0
# gpg: Signature made Mon 24 Jul 2017 15:16:42 BST
# gpg: using RSA key 0x7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream:
qemu-iotests: Avoid unnecessary sleeps
block: Skip implicit nodes in query-block/blockstats
qcow2: Fix sector calculation in qcow2_measure()
dirty-bitmap: Report BlockDirtyInfo.count in bytes, as documented
iotests: Remove a few tests from 'quick' group
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Commits 0db832f and 6cdbceb introduced the automatic insertion of filter
nodes above the top layer of mirror and commit block jobs. The
assumption made there was that since libvirt doesn't do node-level
management of the block layer yet, it shouldn't be affected by added
nodes.
This is true as far as commands issued by libvirt are concerned. It only
uses BlockBackend names to address nodes, so any operations it performs
still operate on the root of the tree as intended.
However, the assumption breaks down when you consider query commands,
which return data for the wrong node now. These commands also return
information on some child nodes (bs->file and/or bs->backing), which
libvirt does make use of, and which refer to the wrong nodes, too.
One of the consequences is that oVirt gets wrong information about the
image size and stops the VM in response as long as a mirror or commit
job is running:
https://bugzilla.redhat.com/show_bug.cgi?id=1470634
This patch fixes the problem by hiding the implicit nodes created
automatically by the mirror and commit block jobs in the output of
query-block and BlockBackend-based query-blockstats as long as the user
doesn't indicate that they are aware of those nodes by providing a node
name for them in the QMP command to start the block job.
The node-based commands query-named-block-nodes and query-blockstats
with query-nodes=true still show all nodes, including implicit ones.
This ensures that users that are capable of node-level management can
still access the full information; users that only know BlockBackends
won't use these commands.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Tested-by: Eric Blake <eblake@redhat.com>
|
|
BlockdevRef is an alternate of BlockdevOptions (inline definition) and
str (reference to an existing block device by name). BlockdevRef
value "" is special: "no block device should be referenced." It's
actually interpreted that way in just one place: optional member
@backing of COW formats. Semantics:
* Present means "use this block device" as backing storage
* Absent means "default to the one stored in the image"
* Except "" means "don't use backing storage at all"
The first two are perfectly normal: when the parameter is absent, it
defaults to an implied value, but the value's meaning is the same.
The third one overloads the parameter with a second meaning. The
overloading is *implicit*, i.e. it's not visible in the types. Works
here, because "" is not a value block device ID.
Pressing argument values the schema accepts, but are semantically
invalid, into service to mean "do something else entirely" is not
general, as suitable invalid values need not exist. I also find it
ugly.
To clean this up, we could add a separate flag argument to suppress
@backing, or add a distinct value to @backing. This commit implements
the latter: add JSON null to the values of @backing, deprecate "".
Because we're so close to the 2.10 freeze, implement it in the
stupidest way possible: have qmp_blockdev_add() rewrite null to ""
before anything else can see the null. Works, because BlockdevRef
occurs only within arguments of blockdev-add. The proper way to do it
would be rewriting "" to null, preferably in a cleaner way, but that
requires fixing up code to work with null. Add a TODO comment for
that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
|
|
Make visit_type_null() take an @obj argument like its buddies. This
helps keep the next commit simple.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
|
|
With -blockdev/-device, users can indirectly create anonymous
BlockBackends, while the state of such backends is still of interest. As
a preparation for making such BBs visible in query-block, make sure that
they can be identified even without a name by adding the ID/QOM path of
their qdev device to BlockInfo.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
|
|
bdrv_measure() provides a conservative maximum for the size of a new
image. This information is handy if storage needs to be allocated (e.g.
a SAN or an LVM volume) ahead of time.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170705125738.8777-2-stefanha@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
|