| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
According to ACPI specification 6.2.17 _CCA (Cache Coherency Attribute)
this attribute is compulsory on ARM systems. Add this attribute to
the PCI host bridges as required.
Without this the kernel will produce the error
[Firmware Bug]: PCI device 0000:00:00.0 fail to setup DMA.
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Message-id: 1446460786-13663-1-git-send-email-graeme.gregory@linaro.org
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add GPIO in for the stellaris board which calls
qemu_system_reset_request() on reset request.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Implement the SYSRESETREQ bit of the AIRCR register
for armv7-m (ie. cortex-m3) to trigger a GPIO out.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Change armv7m_init to return the DeviceState* for the NVIC.
This allows access to all GPIO blocks, not just the IRQ inputs.
Move qdev_get_gpio_in() calls out of armv7m_init() into
board code for stellaris and stm32f205 boards.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add a Linux-specific pre-boot routine that matches the device-
specific bootloaders behaviour. This is needed for modern Linux that
expects the ARM PLL in SLCR to be a more even value (not 26).
Cc: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 9a9025ea65572586b50dca4e5819032e3c436d64.1446182614.git.crosthwaite.peter@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add an API for boards to inject their own preboot software (or
firmware) sequence.
The software then returns to the bootloader via the link register. This
allows boards to do their own little bits of firmware setup without
needed to replace the bootloader completely (which is the requirement
for existing firmware support).
The blob is loaded by a callback if and only if doing a linux boot
(similar to the existing write_secondary support).
Rewrite the comment for the primary boot blob.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 070295644c6ac84696d743913296e8cfefb48c15.1446182614.git.crosthwaite.peter@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
These comments start immediately after the current longest name in the
list. Tab them out to the next tab stop to give a little breathing room
and prepare for FIXUP_BOARD_SETUP which will require more indent.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: b9b9bb8f1c307c1ef8a3f26ff1f34fabb34b332e.1446182614.git.crosthwaite.peter@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
We now use epoxy to load opengl libraries. This means we don't need to
link opengl libraries directly if interfaces handled by epoxy. With
this, we just need epoxy headers and epoxy's *.so to build.
Tested with epoxy-1.3.1.
- sdl2/gtk/console egl stuff doesn't require other than epoxy
- milkymist-tmu2 glx stuff doesn't require other than epoxy
(lm32 test is limited, because can't find mmone-bios.bin, so just test
to load libGL with "./lm32-softmmu/qemu-system-lm32 -M milkymist,accel=qtest")
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
[ lm32 tested by kraxel ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
We have two issues with our qapi union layout:
1) Even though the QMP wire format spells the tag 'type', the
C code spells it 'kind', requiring some hacks in the generator.
2) The C struct uses an anonymous union, which places all tag
values in the same namespace as all non-variant members. This
leads to spurious collisions if a tag value matches a non-variant
member's name.
Make the conversion to the new layout for memory-related code.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-21-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
We have two issues with our qapi union layout:
1) Even though the QMP wire format spells the tag 'type', the
C code spells it 'kind', requiring some hacks in the generator.
2) The C struct uses an anonymous union, which places all tag
values in the same namespace as all non-variant members. This
leads to spurious collisions if a tag value matches a non-variant
member's name.
Make the conversion to the new layout for input-related code.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1445898903-12082-20-git-send-email-eblake@redhat.com>
[Commit message tweaked slightly]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
staging
# gpg: Signature made Thu 29 Oct 2015 18:09:16 GMT using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/block-pull-request:
block: Consider all child nodes in bdrv_requests_pending()
target-arm: xlnx-zynqmp: Add sdhci support.
sdhci: Split sdhci.h for public and internal device usage
sd.h: Move sd.h to include/hw/sd/
virtio: sync the dataplane vring state to the virtqueue before virtio_save
gdb command: qemu handlers
virtio-blk: switch off scsi-passthrough by default
ppc/spapr: add 2.4 compat props
s390x: include HW_COMPAT_* props
qemu-gdb: add $qemu_coroutine_sp and $qemu_coroutine_pc
qemu-gdb: extract parts of "qemu coroutine" implementation
qemu-gdb: allow using glibc_pointer_guard() on core dumps
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Commit 71c199c81d29 ("mips_malta: provide ememsize env variable to
kernels") changed the meaning of loaderparams.ram_size to be the whole
of RAM rather than just the low part below where the boot code is placed
for KVM, but it didn't update the PC initialisation for KVM to use
ram_low_size. Fix that now.
Fixes: 71c199c81d29 ("mips_malta: provide ememsize env variable to kernels")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Add two SYSBUS_SDHCI devices for xlnx-zynqmp
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Split sdhci.h into pubilc version (i.e include/hw/sd/sdhci.h) and
internal version (i.e hw/sd/sdhci-interna.h) based on register
declarations and object declaration.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Create a sd directory under include/hw/ and move sd.h to
include/hw/sd/
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
When creating snapshot with the dataplane enabled, the snapshot file gets
not the actual state of virtqueue, because the current state is stored in
VirtIOBlockDataPlane. Therefore, before saving snapshot need to sync
the dataplane vring state to the virtqueue. The dataplane will resume its
work at the next notify virtqueue.
When snapshot loads with loadvm we get a message:
VQ 0 size 0x80 Guest index 0x15f5 inconsistent with Host index 0x0:
delta 0x15f5
error while loading state for instance 0x0 of device
'0000:00:08.0/virtio-blk'
Error -1 while loading VM state
to reproduce the error I used the following hmp commands:
savevm snap1
loadvm snap1
qemu parameters:
--enable-kvm -smp 4 -m 1024 -drive file=/var/lib/libvirt/images/centos6.4.qcow2,if=none,id=drive-virtio-disk0,format=qcow2,cache=none,aio=native -device virtio-blk-pci,scsi=off,bus=pci.0,addr=0x8,drive=drive-virtio-disk0,id=virtio-disk0 -set device.virtio-disk0.x-data-plane=on
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Message-id: 1445859777-2982-1-git-send-email-den@openvz.org
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Devices that are compliant with virtio-1 do not support scsi
passthrough any more (and it has not been a recommended setup
anyway for quite some time). To avoid having to switch it off
explicitly in newer qemus that turn on virtio-1 by default, let's
switch the default to scsi=false for 2.5.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1444991154-79217-4-git-send-email-cornelia.huck@de.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
HW_COMPAT_2_4 will become non-empty: prepare for it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-id: 1444991154-79217-3-git-send-email-cornelia.huck@de.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
We want to inherit generic hw compat as well.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-id: 1444991154-79217-2-git-send-email-cornelia.huck@de.ibm.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Enable PCIe device multi-function hot-add, just ensure function 0 is added
last, then driver will get the notification to scan the slot.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
In case user want to cancel the hot-add operation, should roll back,
device_del the added function that still don`t work.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit df0acded19ec4b826aa095cfc19d341bd66fafd3.
There's no point to it now that the only user has been reverted.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit aa8580cddf011e8cedcf87f7a0fdea7549fc4704.
As described in
http://article.gmane.org/gmane.comp.emulators.qemu/371432
that commit causes linux guests to crash on memory hot-unplug.
The original problem it's trying to solve has now
been addressed within virtio.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Deprecated in favor of virtqueue_map.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
Note: virtqueue_map already validates input
so virtio-scsi does not have to.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
This also fixes a minor bug:
- virtqueue_map_sg(port->elem.out_sg, port->elem.out_addr,
- port->elem.out_num, 1);
is wrong: out_sg is not written so should not be marked dirty.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
Drop deprecated use of virtqueue_map_sg.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
Drop use of the deprecated virtio_map_sg in virtio core.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
virtio_map_sg currently fails if one of the entries it's mapping is
contigious in GPA but not HVA address space. Introduce virtio_map which
handles this by splitting sg entries.
This new API generally turns out to be a good idea since it's harder to
misuse: at least in one case the existing one was used incorrectly.
This will still fail if there's no space left in the sg, but luckily max
queue size in use is currently 256, while max sg size is 1024, so we
should be OK even is all entries happen to cross a single DIMM boundary.
Won't work well with very small DIMM sizes, unfortunately:
e.g. this will fail with 4K DIMMs where a single
request might span a large number of DIMMs.
Let's hope these are uncommon - at least we are not breaking things.
Note: virtio-scsi calls virtio_map_sg on data loaded from network, and
validates input, asserting on failure. Copy the validating code here -
it will be dropped from virtio-scsi in a follow-up patch.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
currently acpi_memory_plug_cb() sets is_inserting for
cold- and hot-plugged DIMMs as result ASL MHPD.MSCN()
method issues device check even for every coldplugged
DIMM. There isn't much harm in it but if we try to
unplug such DIMM, OSPM will issue device check
intstead of device eject event. So OSPM won't eject
memory module as expected and it will try to eject it
only when another memory device is hot-(un)plugged.
As a fix do not set 'is_inserting' event and do not
issue SCI for cold-plugged DIMMs as they are
enumerated and activated by OSPM during guest's boot.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We are sending msg fields, use sizeof on these
and not on local variables which happen to
have a matching type.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We are using local msg structures everywhere, use them
for sizeof as well.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: b7ce7e98a051479453744aded122789531d80a44.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 5bbad71517ca728d8865f7b9f998baa0df022794.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() output is following the same format as the
above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 57e565982db94fb433c32dfa17608888464d21de.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() output is following the same format as the
above debug.
Adding some missing qemu_log_mask call for bad registers.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 293e08f31cbb4df84d58f693243e61e770c73b3a.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 29885ffea2577eaf2288c1d17fd87ee951748b49.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() output is following the same format as
the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 328acfe6fc09a5afdbfbfd5220e0869fd5082660.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
The qemu_log_mask() outputis following the same format as
the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 4f2007adcf0f579864bb4dd8a825824e0e9098b8.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 47b8759b251d356c633faf7ea34f897f340aea4e.1445781957.git.jcd@tribudubois.net
[PMM: Drop attempt to print the ram_addr of a memory region in
one DPRINTF, which (a) was using the wrong format string so
didn't build on 32-bit and (b) was incorrectly looking at a
private field of a MemoryRegion struct]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
We should always go through VirtBoardInfo when we need the memmap.
To avoid using a15memmap directly, in this case, we need to defer
the max-cpus check from class init time to instance init time. In
class init we now use MAX_CPUMASK_BITS for max_cpus initialization,
which is the maximum QEMU supports, and also, incidentally, the
maximum KVM/gicv3 currently supports. Also, a nice side-effect of
delaying the max-cpus check is that we now get more appropriate
error messages for gicv2 machines that try to configure more than
123 cpus. Before this patch it would complain that the requested
number of cpus was greater than 123, but for gicv2 configs, it
should complain that the number is greater than 8.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 1445189728-860-3-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Currently, if the kernel does not have live migration API, the migration
will still be attempted, but vGIC save/restore functions will just not do
anything. This will result in a broken machine state.
This patch fixes the problem by adding migration blocker if kernel API is
not supported.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Guest OS may issue VMXNET3_CMD_GET_STATS even before device was
activated (for example in linux, after insmod but prior net-dev open).
Accessing shared descriptors prior device activation is illegal as the
VMXNET3State structures have not been fully initialized.
As a result, guest memory gets corrupted and may lead to guest OS
crashes.
Fix, by not filling the stats descriptors if device is inactive.
Reported-by: Leonid Shatz <leonid.shatz@ravellosystems.com>
Acked-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Dana Rubin <dana.rubin@ravellosystems.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Set initial MAC address to the one specified by the command line.
Signed-off-by: Sebastian Huber <sebastian.huber@embedded-brains.de>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
staging
Xen 2015-10-26
# gpg: Signature made Mon 26 Oct 2015 11:32:50 GMT using RSA key ID 70E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
* remotes/sstabellini/tags/xen-2015-10-26:
xen-platform: Replace assert() with appropriate error reporting
xen_platform: switch to realize
Qemu/Xen: Fix early freeing MSIX MMIO memory region
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Commit dbb7405d8caad0814ceddd568cb49f163a847561 made it possible to
trigger an assert using "-device xen-platform". Replace it with
appropriate error reporting.
Before:
$ qemu-system-x86_64 -device xen-platform
qemu-system-x86_64: hw/i386/xen/xen_platform.c:391: xen_platform_initfn: Assertion `xen_enabled()' failed.
Aborted (core dumped)
$
After:
$ qemu-system-x86_64 -device xen-platform
qemu-system-x86_64: -device xen-platform: xen-platform device requires the Xen accelerator
$
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
Use realize to initialize the xen_platform device
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
into staging
ivshmem series
# gpg: Signature made Mon 26 Oct 2015 09:27:46 GMT using RSA key ID 75969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/ivshmem-pull-request: (51 commits)
doc: document ivshmem & hugepages
ivshmem: use little-endian int64_t for the protocol
ivshmem: use kvm irqfd for msi notifications
ivshmem: rename MSI eventfd_table
ivshmem: remove EventfdEntry.vector
ivshmem: add hostmem backend
ivshmem: use qemu_strtosz()
ivshmem: do not keep shm_fd open
tests: add ivshmem qtest
qtest: add qtest_add_abrt_handler()
msix: implement pba write (but read-only)
contrib: remove unnecessary strdup()
ivshmem: add check on protocol version in QEMU
docs: update ivshmem device spec
ivshmem-server: fix hugetlbfs support
ivshmem-server: use a uint16 for client ID
ivshmem-client: check the number of vectors
contrib: add ivshmem client and server
util: const event_notifier_get_fd() argument
ivshmem: reset mask on device reset
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
msix->mmio is added to XenPCIPassthroughState's object as property.
object_finalize_child_property is called for XenPCIPassthroughState's
object, which calls object_property_del_all, which is going to try to
delete msix->mmio. object_finalize_child_property() will access
msix->mmio's obj. But the whole msix struct has already been freed
by xen_pt_msix_delete. This will cause segment fault when msix->mmio
has been overwritten.
This patch is to fix the issue.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
The current ivshmem protocol uses 'long' for integers. But the
sizeof(long) depends on the host and the endianess is not defined, which
may cause portability troubles.
Instead, switch to using little-endian int64_t. This breaks the
protocol, except on x64 little-endian host where this change
should be compatible.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
|
