aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-03-10qtest/ahci: Add DMA test variantsJohn Snow1-6/+28
These test a few different pathways in the AHCI code. short: Test the minimum transfer size, exactly one sector. simple: Test a transfer using a single PRD, in this case, 4K. double: Test transferring 8K, which we will split up as two PRDs. long: Test transferring a lot of data using many PRDs, 256K. Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424905602-24715-5-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10libqos/ahci: add ahci command helpersJohn Snow2-0/+47
ahci_command_set_flags: Set additional flags in the command header. ahci_command_clr_flags: Clear flags from the command header. ahci_command_set_offset: Change the IO sector from 0. ahci_command_adjust: Adjust many values simultaneously. To be used to adjust the command header if the default values/guesses were incorrect or undesirable. Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424905602-24715-4-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> [ kwolf: Fixed conflicting prototype for ahci_command_adjust() ] Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qtest/ahci: Add a macro bootup routineJohn Snow1-6/+17
Add a routine that can be used to engage the AHCI device at a not-granular level so that bringing up the functionality of the HBA is easy in future tests that are not concerned with testing the bring-up process. Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424905602-24715-3-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10libqos/ahci: Zero-fill AHCI headersJohn Snow1-1/+1
Even though it's just the reserved space, make sure they're zeroes. Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424905602-24715-2-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qtest/ide: Test flush / retry for ISA and PCIJohn Snow1-5/+15
This patch adds tests for werror and rerror functionality for the PCI and ISA ide buses. Tests for the AHCI device are to be included at a later date after requisite patches have been merged upstream to support needed functionality by the tests. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Message-id: 1424708286-16483-18-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ahci: Recompute cur_cmd on migrate post loadJohn Snow1-0/+7
When the AHCI HBA device is migrated, all of the information that led to the request being created is stored in the AHCIDevice structures, except for pointers into guest data where return information needs to be stored. The "cur_cmd" field is usually responsible for this. To rebuild the cur_cmd pointer post-migration, we can utilize the busy_slot index to figure out where the command header we are still processing is. This allows a machine in a halted state from rerror=stop or werror=stop to be migrated and resume operations without issue. Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-17-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ahci: add support for restarting non-queued commandsPaolo Bonzini1-8/+15
This is easy, since start_dma already restarts processing from the beginning of the PRDT. Migration is also easy to cover; the comment about busy_slot is wrong, busy_slot will only be set if there is an error. In this case we have nothing to do really. The core IDE code will restart the operation and command list processing will proceed after the erroring command has been completed. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-16-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ahci: Migrate IDEStatusJohn Snow2-0/+4
Amazingly, we weren't doing this before. Make sure we migrate the IDEState structure that belongs to the AHCIDevice.IDEBus structure during migrations. No version numbering changes because AHCI is not officially migratable (and we can all see with good reason why) so we do not impact any official builds by altering the stream and leaving it at version 1. This fixes the rerror=stop/werror=stop test case where we wish to migrate a halted job. Previously, the error code would not migrate, so even if the job completed successfully, AHCI would report an error because it would still have the placeholder error code from initialization time. Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-15-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: support PIO restart for the ISA controllerPaolo Bonzini1-1/+2
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-14-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: make more functions staticPaolo Bonzini2-8/+8
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-13-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: commonize io_buffer_index initializationPaolo Bonzini2-4/+2
Resetting the io_buffer_index to 0 is commonized, with the exception of the case within ide_atapi_cmd_reply, where we need to reset this index to 0 prior to the ide_atapi_cmd_reply_end call. Note that not all calls to ide_atapi_cmd_reply_end expect the index to be 0, so setting it there is not appropriate. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-12-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: migrate initial request state via IDEBusPaolo Bonzini1-1/+4
This only breaks backwards migration compatibility if the bus is in an error state. It is in principle possible to avoid this by making two subsections (one for version 1, and one for version 2, but with the same name) with different "_needed" callbacks. The v1 callback would return true if error_status != 0 and the bus is PATA; the v2 callback would return true if error_status != 0 and the bus is AHCI. Forward migration keeps working. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-11-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: place initial state of the current request to IDEBusPaolo Bonzini4-12/+16
This moves more common restarting logic to the core IDE code. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-10-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: replace set_unit callback with more IDEBus statePaolo Bonzini6-26/+15
Start moving the initial state of the current request to IDEBus, so that AHCI can use it. The set_unit callback is not used anymore once this is done. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-9-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: remove restart_cb callbackPaolo Bonzini4-16/+0
With restarts now handled by ide_restart_cb and the IDEDMAOps.restart_dma() member, remove the old restart_cb callback. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-8-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: move restart callback to common codePaolo Bonzini4-81/+81
With BMDMA specific excised from the restart functions, create a HBA-agnostic restart callback to be shared between the different HBAs. Change the callback registered with the vmstate_change handler to always point to ide_restart_cb instead of relying on the IDEDMAOps.restart_cb() member. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-7-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: pass IDEBus to the restart_cbPaolo Bonzini2-6/+6
Pass the containing IDEBus to the restart_cb instead of the more specific BMDMAState child. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-6-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: do not use BMDMA in restart callbackPaolo Bonzini1-3/+3
Whenever an error stops the VM, ide_handle_rw_error does "s->bus->dma->unit = s->unit". So we can just use idebus_active_if. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-5-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: introduce ide_register_restart_cbPaolo Bonzini5-6/+9
A helper is added that registers the IDEDMAOp .restart_cb() via qemu_add_vm_change_state_handler instead of requiring each HBA to register the callback themselves. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-4-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: prepare to move restart to common codePaolo Bonzini2-5/+8
This patch adds the restart_dma callback and adjusts the ide_restart_dma function to utilize this callback to call the BMDMA-specific restart code instead of statically executing BMDMA-specific code. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-3-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10ide: start extracting ide_restart_dma out of bmdma_restart_dmaPaolo Bonzini1-10/+18
This patch begins refactoring the restart dma functions out of bmdma to be shared with AHCI and other future IDE HBA implementations. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1424708286-16483-2-git-send-email-jsnow@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10BlockConf: Call backend functions to detect geometry and blocksizesEkaterina Tumanova10-6/+46
geometry: hd_geometry_guess function autodetects the drive geometry. This patch adds a block backend call, that probes the backing device geometry. If the inner driver method is implemented and succeeds (currently only for DASDs), the blkconf_geometry will pass-through the backing device geometry. Otherwise will fallback to old logic. blocksize: This patch initializes blocksize properties to 0. In order to set the property a blkconf_blocksizes was introduced. If user didn't set physical or logical blocksize, it will retrieve its value from a driver (only succeeds for DASD), otherwise it will set default 512 value. The blkconf_blocksizes call was added to all users of BlkConf. Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424087278-49393-6-git-send-email-tumanova@linux.vnet.ibm.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10block-backend: Add wrappers for blocksizes and geometry probingEkaterina Tumanova2-0/+12
Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424087278-49393-5-git-send-email-tumanova@linux.vnet.ibm.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10block: Add driver methods to probe blocksizes and geometryEkaterina Tumanova2-0/+115
Introduce driver methods of defining disk blocksizes (physical and logical) and hard drive geometry. Methods are only implemented for "host_device". For "raw" devices driver calls child's method. For now geometry detection will only work for DASD devices. To check that a local check_for_dasd function was introduced. It calls BIODASDINFO2 ioctl and returns its rc. Blocksizes detection function will probe sizes for DASD devices. Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424087278-49393-4-git-send-email-tumanova@linux.vnet.ibm.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10raw-posix: Factor block size detection out of raw_probe_alignment()Ekaterina Tumanova1-16/+35
Put it in new probe_logical_blocksize(). Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424087278-49393-3-git-send-email-tumanova@linux.vnet.ibm.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10block: add bdrv functions for geometry and blocksizeEkaterina Tumanova3-0/+62
Add driver functions for geometry and blocksize detection Signed-off-by: Ekaterina Tumanova <tumanova@linux.vnet.ibm.com> Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424087278-49393-2-git-send-email-tumanova@linux.vnet.ibm.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10blkdebug: fix "once" ruleJohn Snow2-22/+8
Background: The blkdebug scripts are currently engineered so that when a debug event occurs, a prefilter browses a master list of parsed rules for a certain event and adds them to an "active list" of rules to be used for the forthcoming action, provided the events and state numbers match. Then, once the request is received, the last active rule is used to inject an error if certain parameters match. This active list is cleared every time the prefilter injects a new rule for the first time during a debug event. The "once" rule currently causes the error injection, if it is triggered, to only clear the active list. This is insufficient for preventing future injections of the same rule. Remedy: This patch /deletes/ the rule from the list that the prefilter browses, so it is gone for good. In V2, we remove only the rule of interest from the active list instead of allowing the "once" rule to clear the entire list of active rules. Impact: This affects iotests 026. Several ENOSPC tests that used "once" can be seen to have output that shows multiple failure messages. After this patch, the error messages tend to be smaller and less severe, but the injection can still be seen to be working. I have patched the expected output to expect the smaller error messages. Signed-off-by: John Snow <jsnow@redhat.com> Message-id: 1423257977-25630-1-git-send-email-jsnow@redhat.com Reviewed-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10iotests: Add test for different refcount widthsMax Reitz3-0/+272
Add a test for errors specific to certain widths (i.e. snapshots with refcount_bits=1). Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Allow creation with refcount order != 4Max Reitz5-80/+126
Add a creation option to qcow2 for setting the refcount order of images to be created, and respect that option's value. This breaks some test outputs, fix them. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10iotests: Prepare for refcount_bits optionMax Reitz13-37/+41
Some tests do not work well with certain refcount widths (i.e. you cannot create internal snapshots with refcount_bits=1), so make those widths unsupported. Furthermore, add another filter to _filter_img_create in common.filter which filters out the refcount_bits value. This is necessary for test 079, which does actually work with any refcount width, but invoking qemu-img directly leads to the refcount_bits value being visible in the output; use _make_test_img instead which will filter it out. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Use symbolic macros in qcow2_amend_optionsMax Reitz1-15/+16
qcow2_amend_options() should not compare options against some inline strings but rather use the symbolic macros available for each of the creation options. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: refcount_order parameter for qcow2_create2Max Reitz1-11/+36
Add a refcount_order parameter to qcow2_create2(), use that value for the image header and for calculating the size required for preallocation. For now, always pass 4. This addition requires changes to the calculation of the file size for the "full" and "falloc" preallocation modes. That in turn is a nice opportunity to add a comment about that calculation not necessarily being exact (and that being intentional). Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Open images with refcount order != 4Max Reitz1-4/+4
No longer refuse to open images with a different refcount entry width than 16 bits; only reject images with a refcount width larger than 64 bits (which is prohibited by the specification). Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: More helpers for refcount modificationMax Reitz1-2/+119
Add helper functions for getting and setting refcounts in a refcount array for any possible refcount order, and choose the correct one during refcount initialization. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Helper function for refcount modificationMax Reitz2-53/+81
Since refcounts do not always have to be a uint16_t, all refcount blocks and arrays in memory should not have a specific type (thus they become pointers to void) and for accessing them, two helper functions are used (a getter and a setter). Those functions are called indirectly through function pointers in the BDRVQcowState so they may later be exchanged for different refcount orders. With the check and repair functions using this function, the refcount array they are creating will be in big endian byte order; additionally, using realloc_refcount_array() makes the size of this refcount array always cluster-aligned. Both combined allow rebuild_refcount_structure() to drop the bounce buffer which was used to convert parts of the refcount array to big endian byte order and store them on disk. Instead, those parts can now be written directly. [ kwolf: Fixed a build failure on 32 bit and another with old glib ] Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Helper for refcount array reallocationMax Reitz1-49/+81
Add a helper function for reallocating a refcount array, independent of the refcount order. The newly allocated space is zeroed and the function handles failed reallocations gracefully. The helper function will always align the buffer size to a cluster boundary; if storing the refcounts in such an array in big endian byte order, this makes it possible to write parts of the array directly as refcount blocks into the image file. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Use 64 bits for refcount valuesMax Reitz3-25/+23
Refcounts may have a width of up to 64 bits, so qemu should use the same width to represent refcount values internally. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Use unsigned addend for update_refcount()Max Reitz3-24/+52
update_refcount() and qcow2_update_cluster_refcount() currently take a signed addend. At least one caller passes a value directly derived from an absolute refcount that should be reached ("l2_refcount - 1" in expand_zero_clusters_in_l1()). Therefore, the addend should be unsigned as well; this will be especially important for 64 bit refcounts. Because update_refcount() then no longer knows whether the refcount should be increased or decreased, it now requires an additional flag which specified exactly that. The same applies to qcow2_update_cluster_refcount(). Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Only return status from qcow2_get_refcountMax Reitz3-44/+53
Refcounts can theoretically be of type uint64_t; in order to be able to represent the full range, qcow2_get_refcount() cannot use a single variable to represent both all refcount values and also keep some values reserved for errors. One solution would be to add an Error pointer parameter to qcow2_get_refcount(); however, no caller could (currently) pass that error message, so it would have to be emitted immediately and be passed to the next caller by returning -EIO or something similar. Therefore, an Error parameter does not offer any advantages here. The solution applied by this patch is simpler to use. Because no caller would be able to pass the error message, they would have to print it and free it, whereas with this patch the caller only needs to pass the returned integer (which is often a no-op from the code perspective, because that integer will be stored in a variable "ret" which will be returned by the fail path of many callers). Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Do not return new value after refcount updateMax Reitz1-10/+15
qcow2_update_cluster_refcount() does not have any quick access to the new refcount value, it has to call qcow2_get_refcount(). Some callers do not need that new value at all, others call qcow2_get_refcount() themselves anyway (albeit in a different code path, which can however be easily changed), therefore there is no advantage in making qcow2_update_cluster_refcount() return the new value. Drop it. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Add refcount_bits to format-specific infoMax Reitz7-10/+37
Add the bit width of every refcount entry to the format-specific information. In contrast to lazy_refcounts and the corrupt flag, this should be always emitted, even for compat=0.10 although it does not support any refcount width other than 16 bits. This is because if a boolean is optional, one normally assumes it to be false when omitted; but if an integer is not specified, it is rather difficult to guess its value. This new field breaks some test outputs, fix them. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10qcow2: Add two new fields to BDRVQcowStateMax Reitz3-2/+7
Add two new fields regarding refcount information (the bit width of every entry and the maximum refcount value) to the BDRVQcowState. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10libqos: Add virtio MMIO supportMarc Marí4-8/+323
Add virtio MMIO support. Add virtio-blk-test MMIO test case. Signed-off-by: Marc Marí <marc.mari.barcelo@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424812915-25728-6-git-send-email-marc.mari.barcelo@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10libqos: Add malloc genericMarc Marí2-0/+60
This malloc is a basic interface implementation that works for any platform. It should be replaced in the future for a real malloc implementation for each of the platforms. Signed-off-by: Marc Marí <marc.mari.barcelo@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424812915-25728-5-git-send-email-marc.mari.barcelo@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10libqos: Remove PCI assumptions in constants of virtio driverMarc Marí3-32/+33
Convert PCI-specific constants names of libqos virtio driver. Signed-off-by: Marc Marí <marc.mari.barcelo@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424812915-25728-4-git-send-email-marc.mari.barcelo@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10tests: Prepare virtio-blk-test for multi-arch implementationMarc Marí1-65/+89
Modularize functions in virtio-blk-test and add PCI suffix for PCI specific components. Signed-off-by: Marc Marí <marc.mari.barcelo@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424812915-25728-3-git-send-email-marc.mari.barcelo@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10libqos: Change use of pointers to uint64_t in virtioMarc Marí4-28/+37
Convert use of pointers in functions of virtio to uint64_t in order to make it platform-independent. Add casting from pointers (in PCI functions) to uint64_t and vice versa through uintptr_t. Signed-off-by: Marc Marí <marc.mari.barcelo@gmail.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 1424812915-25728-2-git-send-email-marc.mari.barcelo@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-10virtio-blk: Check return value of blk_aio_ioctlFam Zheng1-2/+8
Since commit 1dc936aa84 (virtio-blk: Use blk_aio_ioctl) we silently lose the request if blk_aio_ioctl returns NULL (not implemented). Fix it by directly returning VIRTIO_BLK_S_UNSUPP as we used to do. Signed-off-by: Fam Zheng <famz@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> [ kwolf: Fixed build error on win32 ] Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2015-03-09qcow2: Remove unused struct QCowCreateStateKevin Wolf1-11/+0
The only user went away five years ago with commit a9420734 ('qcow2: Simplify image creation'). It's about time to remove it. Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
2015-03-09block/raw-posix: fix compilation warning on OSXDenis V. Lunev1-0/+2
block/raw-posix.c:947:19: warning: unused variable 's' [-Wunused-variable] BDRVRawState *s = aiocb->bs->opaque; This variable is used only when on of the following macros are defined CONFIG_XFS, CONFIG_FALLOCATE, CONFIG_FALLOCATE_PUNCH_HOLE or CONFIG_FALLOCATE_ZERO_RANGE. Fortunately, CONFIG_FALLOCATE_PUNCH_HOLE and CONFIG_FALLOCATE_ZERO_RANGE could be defined only along with CONFIG_FALLOCATE. Therefore checking for CONFIG_XFS or CONFIG_FALLOCATE would be enough. Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Peter Maydell <peter.maydell@linaro.org> CC: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
generated by cgit v1.1 at 2024-12-27 11:56:39 +0000