diff options
Diffstat (limited to 'hw/block')
| -rw-r--r-- | hw/block/m25p80.c | 5 | ||||
| -rw-r--r-- | hw/block/virtio-blk.c | 25 | ||||
| -rw-r--r-- | hw/block/xen_disk.c | 13 |
3 files changed, 39 insertions, 4 deletions
diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c index 8c3b7f0..02a1544 100644 --- a/hw/block/m25p80.c +++ b/hw/block/m25p80.c @@ -624,6 +624,11 @@ static int m25p80_init(SSISlave *ss) if (dinfo && dinfo->bdrv) { DB_PRINT_L(0, "Binding to IF_MTD drive\n"); s->bdrv = dinfo->bdrv; + if (bdrv_is_read_only(s->bdrv)) { + fprintf(stderr, "Can't use a read-only drive"); + return 1; + } + /* FIXME: Move to late init */ if (bdrv_read(s->bdrv, 0, s->storage, DIV_ROUND_UP(s->size, BDRV_SECTOR_SIZE))) { diff --git a/hw/block/virtio-blk.c b/hw/block/virtio-blk.c index e2f55cc..13f6d82 100644 --- a/hw/block/virtio-blk.c +++ b/hw/block/virtio-blk.c @@ -460,9 +460,9 @@ static void virtio_blk_dma_restart_cb(void *opaque, int running, static void virtio_blk_reset(VirtIODevice *vdev) { -#ifdef CONFIG_VIRTIO_BLK_DATA_PLANE VirtIOBlock *s = VIRTIO_BLK(vdev); +#ifdef CONFIG_VIRTIO_BLK_DATA_PLANE if (s->dataplane) { virtio_blk_data_plane_stop(s->dataplane); } @@ -473,6 +473,7 @@ static void virtio_blk_reset(VirtIODevice *vdev) * are per-device request lists. */ bdrv_drain_all(); + bdrv_set_enable_write_cache(s->bs, s->original_wce); } /* coalesce internal state, copy to pci i/o region 0 @@ -564,7 +565,25 @@ static void virtio_blk_set_status(VirtIODevice *vdev, uint8_t status) } features = vdev->guest_features; - bdrv_set_enable_write_cache(s->bs, !!(features & (1 << VIRTIO_BLK_F_WCE))); + + /* A guest that supports VIRTIO_BLK_F_CONFIG_WCE must be able to send + * cache flushes. Thus, the "auto writethrough" behavior is never + * necessary for guests that support the VIRTIO_BLK_F_CONFIG_WCE feature. + * Leaving it enabled would break the following sequence: + * + * Guest started with "-drive cache=writethrough" + * Guest sets status to 0 + * Guest sets DRIVER bit in status field + * Guest reads host features (WCE=0, CONFIG_WCE=1) + * Guest writes guest features (WCE=0, CONFIG_WCE=1) + * Guest writes 1 to the WCE configuration field (writeback mode) + * Guest sets DRIVER_OK bit in status field + * + * s->bs would erroneously be placed in writethrough mode. + */ + if (!(features & (1 << VIRTIO_BLK_F_CONFIG_WCE))) { + bdrv_set_enable_write_cache(s->bs, !!(features & (1 << VIRTIO_BLK_F_WCE))); + } } static void virtio_blk_save(QEMUFile *f, void *opaque) @@ -674,6 +693,7 @@ static int virtio_blk_device_init(VirtIODevice *vdev) } blkconf_serial(&blk->conf, &blk->serial); + s->original_wce = bdrv_enable_write_cache(blk->conf.bs); if (blkconf_geometry(&blk->conf, NULL, 65535, 255, 255) < 0) { return -1; } @@ -683,7 +703,6 @@ static int virtio_blk_device_init(VirtIODevice *vdev) s->bs = blk->conf.bs; s->conf = &blk->conf; - memcpy(&(s->blk), blk, sizeof(struct VirtIOBlkConf)); s->rq = NULL; s->sector_mask = (s->conf->logical_block_size / BDRV_SECTOR_SIZE) - 1; diff --git a/hw/block/xen_disk.c b/hw/block/xen_disk.c index 668cc06..098f6c6 100644 --- a/hw/block/xen_disk.c +++ b/hw/block/xen_disk.c @@ -405,6 +405,7 @@ static int ioreq_map(struct ioreq *ioreq) xen_be_printf(&ioreq->blkdev->xendev, 0, "can't map grant ref %d (%s, %d maps)\n", refs[i], strerror(errno), ioreq->blkdev->cnt_map); + ioreq->mapped = 1; ioreq_unmap(ioreq); return -1; } @@ -809,10 +810,15 @@ static int blk_connect(struct XenDevice *xendev) xen_be_printf(&blkdev->xendev, 2, "create new bdrv (xenbus setup)\n"); blkdev->bs = bdrv_new(blkdev->dev); if (blkdev->bs) { + Error *local_err = NULL; BlockDriver *drv = bdrv_find_whitelisted_format(blkdev->fileproto, readonly); if (bdrv_open(blkdev->bs, - blkdev->filename, NULL, qflags, drv) != 0) { + blkdev->filename, NULL, qflags, drv, &local_err) != 0) + { + xen_be_printf(&blkdev->xendev, 0, "error: %s\n", + error_get_pretty(local_err)); + error_free(local_err); bdrv_unref(blkdev->bs); blkdev->bs = NULL; } @@ -824,6 +830,11 @@ static int blk_connect(struct XenDevice *xendev) /* setup via qemu cmdline -> already setup for us */ xen_be_printf(&blkdev->xendev, 2, "get configured bdrv (cmdline setup)\n"); blkdev->bs = blkdev->dinfo->bdrv; + if (bdrv_is_read_only(blkdev->bs) && !readonly) { + xen_be_printf(&blkdev->xendev, 0, "Unexpected read-only drive"); + blkdev->bs = NULL; + return -1; + } /* blkdev->bs is not create by us, we get a reference * so we can bdrv_unref() unconditionally */ bdrv_ref(blkdev->bs); |