Linux headers: update

Update against Linux 5.8-rc1.

Signed-off-by: Cornelia Huck <cohuck@redhat.com>

1 files changed, 322 insertions, 0 deletions

diff --git a/linux-headers/linux/vfio.h b/linux-headers/linux/vfio.h
index a41c452..f09df26 100644
--- a/linux-headers/linux/vfio.h
+++ b/linux-headers/linux/vfio.h
@@ -305,6 +305,7 @@ struct vfio_region_info_cap_type {
 #define VFIO_REGION_TYPE_PCI_VENDOR_MASK	(0xffff)
 #define VFIO_REGION_TYPE_GFX                    (1)
 #define VFIO_REGION_TYPE_CCW			(2)
+#define VFIO_REGION_TYPE_MIGRATION              (3)
 
 /* sub-types for VFIO_REGION_TYPE_PCI_* */
 
@@ -378,6 +379,235 @@ struct vfio_region_gfx_edid {
 
 /* sub-types for VFIO_REGION_TYPE_CCW */
 #define VFIO_REGION_SUBTYPE_CCW_ASYNC_CMD	(1)
+#define VFIO_REGION_SUBTYPE_CCW_SCHIB		(2)
+#define VFIO_REGION_SUBTYPE_CCW_CRW		(3)
+
+/* sub-types for VFIO_REGION_TYPE_MIGRATION */
+#define VFIO_REGION_SUBTYPE_MIGRATION           (1)
+
+/*
+ * The structure vfio_device_migration_info is placed at the 0th offset of
+ * the VFIO_REGION_SUBTYPE_MIGRATION region to get and set VFIO device related
+ * migration information. Field accesses from this structure are only supported
+ * at their native width and alignment. Otherwise, the result is undefined and
+ * vendor drivers should return an error.
+ *
+ * device_state: (read/write)
+ *      - The user application writes to this field to inform the vendor driver
+ *        about the device state to be transitioned to.
+ *      - The vendor driver should take the necessary actions to change the
+ *        device state. After successful transition to a given state, the
+ *        vendor driver should return success on write(device_state, state)
+ *        system call. If the device state transition fails, the vendor driver
+ *        should return an appropriate -errno for the fault condition.
+ *      - On the user application side, if the device state transition fails,
+ *	  that is, if write(device_state, state) returns an error, read
+ *	  device_state again to determine the current state of the device from
+ *	  the vendor driver.
+ *      - The vendor driver should return previous state of the device unless
+ *        the vendor driver has encountered an internal error, in which case
+ *        the vendor driver may report the device_state VFIO_DEVICE_STATE_ERROR.
+ *      - The user application must use the device reset ioctl to recover the
+ *        device from VFIO_DEVICE_STATE_ERROR state. If the device is
+ *        indicated to be in a valid device state by reading device_state, the
+ *        user application may attempt to transition the device to any valid
+ *        state reachable from the current state or terminate itself.
+ *
+ *      device_state consists of 3 bits:
+ *      - If bit 0 is set, it indicates the _RUNNING state. If bit 0 is clear,
+ *        it indicates the _STOP state. When the device state is changed to
+ *        _STOP, driver should stop the device before write() returns.
+ *      - If bit 1 is set, it indicates the _SAVING state, which means that the
+ *        driver should start gathering device state information that will be
+ *        provided to the VFIO user application to save the device's state.
+ *      - If bit 2 is set, it indicates the _RESUMING state, which means that
+ *        the driver should prepare to resume the device. Data provided through
+ *        the migration region should be used to resume the device.
+ *      Bits 3 - 31 are reserved for future use. To preserve them, the user
+ *      application should perform a read-modify-write operation on this
+ *      field when modifying the specified bits.
+ *
+ *  +------- _RESUMING
+ *  |+------ _SAVING
+ *  ||+----- _RUNNING
+ *  |||
+ *  000b => Device Stopped, not saving or resuming
+ *  001b => Device running, which is the default state
+ *  010b => Stop the device & save the device state, stop-and-copy state
+ *  011b => Device running and save the device state, pre-copy state
+ *  100b => Device stopped and the device state is resuming
+ *  101b => Invalid state
+ *  110b => Error state
+ *  111b => Invalid state
+ *
+ * State transitions:
+ *
+ *              _RESUMING  _RUNNING    Pre-copy    Stop-and-copy   _STOP
+ *                (100b)     (001b)     (011b)        (010b)       (000b)
+ * 0. Running or default state
+ *                             |
+ *
+ * 1. Normal Shutdown (optional)
+ *                             |------------------------------------->|
+ *
+ * 2. Save the state or suspend
+ *                             |------------------------->|---------->|
+ *
+ * 3. Save the state during live migration
+ *                             |----------->|------------>|---------->|
+ *
+ * 4. Resuming
+ *                  |<---------|
+ *
+ * 5. Resumed
+ *                  |--------->|
+ *
+ * 0. Default state of VFIO device is _RUNNNG when the user application starts.
+ * 1. During normal shutdown of the user application, the user application may
+ *    optionally change the VFIO device state from _RUNNING to _STOP. This
+ *    transition is optional. The vendor driver must support this transition but
+ *    must not require it.
+ * 2. When the user application saves state or suspends the application, the
+ *    device state transitions from _RUNNING to stop-and-copy and then to _STOP.
+ *    On state transition from _RUNNING to stop-and-copy, driver must stop the
+ *    device, save the device state and send it to the application through the
+ *    migration region. The sequence to be followed for such transition is given
+ *    below.
+ * 3. In live migration of user application, the state transitions from _RUNNING
+ *    to pre-copy, to stop-and-copy, and to _STOP.
+ *    On state transition from _RUNNING to pre-copy, the driver should start
+ *    gathering the device state while the application is still running and send
+ *    the device state data to application through the migration region.
+ *    On state transition from pre-copy to stop-and-copy, the driver must stop
+ *    the device, save the device state and send it to the user application
+ *    through the migration region.
+ *    Vendor drivers must support the pre-copy state even for implementations
+ *    where no data is provided to the user before the stop-and-copy state. The
+ *    user must not be required to consume all migration data before the device
+ *    transitions to a new state, including the stop-and-copy state.
+ *    The sequence to be followed for above two transitions is given below.
+ * 4. To start the resuming phase, the device state should be transitioned from
+ *    the _RUNNING to the _RESUMING state.
+ *    In the _RESUMING state, the driver should use the device state data
+ *    received through the migration region to resume the device.
+ * 5. After providing saved device data to the driver, the application should
+ *    change the state from _RESUMING to _RUNNING.
+ *
+ * reserved:
+ *      Reads on this field return zero and writes are ignored.
+ *
+ * pending_bytes: (read only)
+ *      The number of pending bytes still to be migrated from the vendor driver.
+ *
+ * data_offset: (read only)
+ *      The user application should read data_offset field from the migration
+ *      region. The user application should read the device data from this
+ *      offset within the migration region during the _SAVING state or write
+ *      the device data during the _RESUMING state. See below for details of
+ *      sequence to be followed.
+ *
+ * data_size: (read/write)
+ *      The user application should read data_size to get the size in bytes of
+ *      the data copied in the migration region during the _SAVING state and
+ *      write the size in bytes of the data copied in the migration region
+ *      during the _RESUMING state.
+ *
+ * The format of the migration region is as follows:
+ *  ------------------------------------------------------------------
+ * |vfio_device_migration_info|    data section                      |
+ * |                          |     ///////////////////////////////  |
+ * ------------------------------------------------------------------
+ *   ^                              ^
+ *  offset 0-trapped part        data_offset
+ *
+ * The structure vfio_device_migration_info is always followed by the data
+ * section in the region, so data_offset will always be nonzero. The offset
+ * from where the data is copied is decided by the kernel driver. The data
+ * section can be trapped, mmapped, or partitioned, depending on how the kernel
+ * driver defines the data section. The data section partition can be defined
+ * as mapped by the sparse mmap capability. If mmapped, data_offset must be
+ * page aligned, whereas initial section which contains the
+ * vfio_device_migration_info structure, might not end at the offset, which is
+ * page aligned. The user is not required to access through mmap regardless
+ * of the capabilities of the region mmap.
+ * The vendor driver should determine whether and how to partition the data
+ * section. The vendor driver should return data_offset accordingly.
+ *
+ * The sequence to be followed while in pre-copy state and stop-and-copy state
+ * is as follows:
+ * a. Read pending_bytes, indicating the start of a new iteration to get device
+ *    data. Repeated read on pending_bytes at this stage should have no side
+ *    effects.
+ *    If pending_bytes == 0, the user application should not iterate to get data
+ *    for that device.
+ *    If pending_bytes > 0, perform the following steps.
+ * b. Read data_offset, indicating that the vendor driver should make data
+ *    available through the data section. The vendor driver should return this
+ *    read operation only after data is available from (region + data_offset)
+ *    to (region + data_offset + data_size).
+ * c. Read data_size, which is the amount of data in bytes available through
+ *    the migration region.
+ *    Read on data_offset and data_size should return the offset and size of
+ *    the current buffer if the user application reads data_offset and
+ *    data_size more than once here.
+ * d. Read data_size bytes of data from (region + data_offset) from the
+ *    migration region.
+ * e. Process the data.
+ * f. Read pending_bytes, which indicates that the data from the previous
+ *    iteration has been read. If pending_bytes > 0, go to step b.
+ *
+ * The user application can transition from the _SAVING|_RUNNING
+ * (pre-copy state) to the _SAVING (stop-and-copy) state regardless of the
+ * number of pending bytes. The user application should iterate in _SAVING
+ * (stop-and-copy) until pending_bytes is 0.
+ *
+ * The sequence to be followed while _RESUMING device state is as follows:
+ * While data for this device is available, repeat the following steps:
+ * a. Read data_offset from where the user application should write data.
+ * b. Write migration data starting at the migration region + data_offset for
+ *    the length determined by data_size from the migration source.
+ * c. Write data_size, which indicates to the vendor driver that data is
+ *    written in the migration region. Vendor driver must return this write
+ *    operations on consuming data. Vendor driver should apply the
+ *    user-provided migration region data to the device resume state.
+ *
+ * If an error occurs during the above sequences, the vendor driver can return
+ * an error code for next read() or write() operation, which will terminate the
+ * loop. The user application should then take the next necessary action, for
+ * example, failing migration or terminating the user application.
+ *
+ * For the user application, data is opaque. The user application should write
+ * data in the same order as the data is received and the data should be of
+ * same transaction size at the source.
+ */
+
+struct vfio_device_migration_info {
+	__u32 device_state;         /* VFIO device state */
+#define VFIO_DEVICE_STATE_STOP      (0)
+#define VFIO_DEVICE_STATE_RUNNING   (1 << 0)
+#define VFIO_DEVICE_STATE_SAVING    (1 << 1)
+#define VFIO_DEVICE_STATE_RESUMING  (1 << 2)
+#define VFIO_DEVICE_STATE_MASK      (VFIO_DEVICE_STATE_RUNNING | \
+				     VFIO_DEVICE_STATE_SAVING |  \
+				     VFIO_DEVICE_STATE_RESUMING)
+
+#define VFIO_DEVICE_STATE_VALID(state) \
+	(state & VFIO_DEVICE_STATE_RESUMING ? \
+	(state & VFIO_DEVICE_STATE_MASK) == VFIO_DEVICE_STATE_RESUMING : 1)
+
+#define VFIO_DEVICE_STATE_IS_ERROR(state) \
+	((state & VFIO_DEVICE_STATE_MASK) == (VFIO_DEVICE_STATE_SAVING | \
+					      VFIO_DEVICE_STATE_RESUMING))
+
+#define VFIO_DEVICE_STATE_SET_ERROR(state) \
+	((state & ~VFIO_DEVICE_STATE_MASK) | VFIO_DEVICE_SATE_SAVING | \
+					     VFIO_DEVICE_STATE_RESUMING)
+
+	__u32 reserved;
+	__u64 pending_bytes;
+	__u64 data_offset;
+	__u64 data_size;
+};
 
 /*
  * The MSIX mappable capability informs that MSIX data of a BAR can be mmapped
@@ -577,6 +807,7 @@ enum {
 
 enum {
 	VFIO_CCW_IO_IRQ_INDEX,
+	VFIO_CCW_CRW_IRQ_INDEX,
 	VFIO_CCW_NUM_IRQS
 };
 
@@ -785,6 +1016,29 @@ struct vfio_iommu_type1_info_cap_iova_range {
 	struct	vfio_iova_range iova_ranges[];
 };
 
+/*
+ * The migration capability allows to report supported features for migration.
+ *
+ * The structures below define version 1 of this capability.
+ *
+ * The existence of this capability indicates that IOMMU kernel driver supports
+ * dirty page logging.
+ *
+ * pgsize_bitmap: Kernel driver returns bitmap of supported page sizes for dirty
+ * page logging.
+ * max_dirty_bitmap_size: Kernel driver returns maximum supported dirty bitmap
+ * size in bytes that can be used by user applications when getting the dirty
+ * bitmap.
+ */
+#define VFIO_IOMMU_TYPE1_INFO_CAP_MIGRATION  1
+
+struct vfio_iommu_type1_info_cap_migration {
+	struct	vfio_info_cap_header header;
+	__u32	flags;
+	__u64	pgsize_bitmap;
+	__u64	max_dirty_bitmap_size;		/* in bytes */
+};
+
 #define VFIO_IOMMU_GET_INFO _IO(VFIO_TYPE, VFIO_BASE + 12)
 
 /**
@@ -805,6 +1059,12 @@ struct vfio_iommu_type1_dma_map {
 
 #define VFIO_IOMMU_MAP_DMA _IO(VFIO_TYPE, VFIO_BASE + 13)
 
+struct vfio_bitmap {
+	__u64        pgsize;	/* page size for bitmap in bytes */
+	__u64        size;	/* in bytes */
+	__u64 *data;	/* one bit per page */
+};
+
 /**
  * VFIO_IOMMU_UNMAP_DMA - _IOWR(VFIO_TYPE, VFIO_BASE + 14,
  *							struct vfio_dma_unmap)
@@ -814,12 +1074,23 @@ struct vfio_iommu_type1_dma_map {
  * field.  No guarantee is made to the user that arbitrary unmaps of iova
  * or size different from those used in the original mapping call will
  * succeed.
+ * VFIO_DMA_UNMAP_FLAG_GET_DIRTY_BITMAP should be set to get the dirty bitmap
+ * before unmapping IO virtual addresses. When this flag is set, the user must
+ * provide a struct vfio_bitmap in data[]. User must provide zero-allocated
+ * memory via vfio_bitmap.data and its size in the vfio_bitmap.size field.
+ * A bit in the bitmap represents one page, of user provided page size in
+ * vfio_bitmap.pgsize field, consecutively starting from iova offset. Bit set
+ * indicates that the page at that offset from iova is dirty. A Bitmap of the
+ * pages in the range of unmapped size is returned in the user-provided
+ * vfio_bitmap.data.
  */
 struct vfio_iommu_type1_dma_unmap {
 	__u32	argsz;
 	__u32	flags;
+#define VFIO_DMA_UNMAP_FLAG_GET_DIRTY_BITMAP (1 << 0)
 	__u64	iova;				/* IO virtual address */
 	__u64	size;				/* Size of mapping (bytes) */
+	__u8    data[];
 };
 
 #define VFIO_IOMMU_UNMAP_DMA _IO(VFIO_TYPE, VFIO_BASE + 14)
@@ -831,6 +1102,57 @@ struct vfio_iommu_type1_dma_unmap {
 #define VFIO_IOMMU_ENABLE	_IO(VFIO_TYPE, VFIO_BASE + 15)
 #define VFIO_IOMMU_DISABLE	_IO(VFIO_TYPE, VFIO_BASE + 16)
 
+/**
+ * VFIO_IOMMU_DIRTY_PAGES - _IOWR(VFIO_TYPE, VFIO_BASE + 17,
+ *                                     struct vfio_iommu_type1_dirty_bitmap)
+ * IOCTL is used for dirty pages logging.
+ * Caller should set flag depending on which operation to perform, details as
+ * below:
+ *
+ * Calling the IOCTL with VFIO_IOMMU_DIRTY_PAGES_FLAG_START flag set, instructs
+ * the IOMMU driver to log pages that are dirtied or potentially dirtied by
+ * the device; designed to be used when a migration is in progress. Dirty pages
+ * are logged until logging is disabled by user application by calling the IOCTL
+ * with VFIO_IOMMU_DIRTY_PAGES_FLAG_STOP flag.
+ *
+ * Calling the IOCTL with VFIO_IOMMU_DIRTY_PAGES_FLAG_STOP flag set, instructs
+ * the IOMMU driver to stop logging dirtied pages.
+ *
+ * Calling the IOCTL with VFIO_IOMMU_DIRTY_PAGES_FLAG_GET_BITMAP flag set
+ * returns the dirty pages bitmap for IOMMU container for a given IOVA range.
+ * The user must specify the IOVA range and the pgsize through the structure
+ * vfio_iommu_type1_dirty_bitmap_get in the data[] portion. This interface
+ * supports getting a bitmap of the smallest supported pgsize only and can be
+ * modified in future to get a bitmap of any specified supported pgsize. The
+ * user must provide a zeroed memory area for the bitmap memory and specify its
+ * size in bitmap.size. One bit is used to represent one page consecutively
+ * starting from iova offset. The user should provide page size in bitmap.pgsize
+ * field. A bit set in the bitmap indicates that the page at that offset from
+ * iova is dirty. The caller must set argsz to a value including the size of
+ * structure vfio_iommu_type1_dirty_bitmap_get, but excluding the size of the
+ * actual bitmap. If dirty pages logging is not enabled, an error will be
+ * returned.
+ *
+ * Only one of the flags _START, _STOP and _GET may be specified at a time.
+ *
+ */
+struct vfio_iommu_type1_dirty_bitmap {
+	__u32        argsz;
+	__u32        flags;
+#define VFIO_IOMMU_DIRTY_PAGES_FLAG_START	(1 << 0)
+#define VFIO_IOMMU_DIRTY_PAGES_FLAG_STOP	(1 << 1)
+#define VFIO_IOMMU_DIRTY_PAGES_FLAG_GET_BITMAP	(1 << 2)
+	__u8         data[];
+};
+
+struct vfio_iommu_type1_dirty_bitmap_get {
+	__u64              iova;	/* IO virtual address */
+	__u64              size;	/* Size of iova range */
+	struct vfio_bitmap bitmap;
+};
+
+#define VFIO_IOMMU_DIRTY_PAGES             _IO(VFIO_TYPE, VFIO_BASE + 17)
+
 /* -------- Additional API for SPAPR TCE (Server POWERPC) IOMMU -------- */
 
 /*