pci: move pci core code to hw/pci

Move files and modify makefiles to pick them at the
new location.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

1 files changed, 0 insertions, 681 deletions

diff --git a/hw/shpc.c b/hw/shpc.c
deleted file mode 100644
index 4597bbd..0000000
--- a/hw/shpc.c
+++ /dev/null
@@ -1,681 +0,0 @@
-#include <strings.h>
-#include <stdint.h>
-#include "range.h"
-#include "range.h"
-#include "shpc.h"
-#include "pci.h"
-#include "pci_internals.h"
-#include "msi.h"
-
-/* TODO: model power only and disabled slot states. */
-/* TODO: handle SERR and wakeups */
-/* TODO: consider enabling 66MHz support */
-
-/* TODO: remove fully only on state DISABLED and LED off.
- * track state to properly record this. */
-
-/* SHPC Working Register Set */
-#define SHPC_BASE_OFFSET  0x00 /* 4 bytes */
-#define SHPC_SLOTS_33     0x04 /* 4 bytes. Also encodes PCI-X slots. */
-#define SHPC_SLOTS_66     0x08 /* 4 bytes. */
-#define SHPC_NSLOTS       0x0C /* 1 byte */
-#define SHPC_FIRST_DEV    0x0D /* 1 byte */
-#define SHPC_PHYS_SLOT    0x0E /* 2 byte */
-#define SHPC_PHYS_NUM_MAX 0x7ff
-#define SHPC_PHYS_NUM_UP  0x2000
-#define SHPC_PHYS_MRL     0x4000
-#define SHPC_PHYS_BUTTON  0x8000
-#define SHPC_SEC_BUS      0x10 /* 2 bytes */
-#define SHPC_SEC_BUS_33   0x0
-#define SHPC_SEC_BUS_66   0x1 /* Unused */
-#define SHPC_SEC_BUS_MASK 0x7
-#define SHPC_MSI_CTL      0x12 /* 1 byte */
-#define SHPC_PROG_IFC     0x13 /* 1 byte */
-#define SHPC_PROG_IFC_1_0 0x1
-#define SHPC_CMD_CODE     0x14 /* 1 byte */
-#define SHPC_CMD_TRGT     0x15 /* 1 byte */
-#define SHPC_CMD_TRGT_MIN 0x1
-#define SHPC_CMD_TRGT_MAX 0x1f
-#define SHPC_CMD_STATUS   0x16 /* 2 bytes */
-#define SHPC_CMD_STATUS_BUSY          0x1
-#define SHPC_CMD_STATUS_MRL_OPEN      0x2
-#define SHPC_CMD_STATUS_INVALID_CMD   0x4
-#define SHPC_CMD_STATUS_INVALID_MODE  0x8
-#define SHPC_INT_LOCATOR  0x18 /* 4 bytes */
-#define SHPC_INT_COMMAND  0x1
-#define SHPC_SERR_LOCATOR 0x1C /* 4 bytes */
-#define SHPC_SERR_INT     0x20 /* 4 bytes */
-#define SHPC_INT_DIS      0x1
-#define SHPC_SERR_DIS     0x2
-#define SHPC_CMD_INT_DIS  0x4
-#define SHPC_ARB_SERR_DIS 0x8
-#define SHPC_CMD_DETECTED 0x10000
-#define SHPC_ARB_DETECTED 0x20000
- /* 4 bytes * slot # (start from 0) */
-#define SHPC_SLOT_REG(s)         (0x24 + (s) * 4)
- /* 2 bytes */
-#define SHPC_SLOT_STATUS(s)       (0x0 + SHPC_SLOT_REG(s))
-
-/* Same slot state masks are used for command and status registers */
-#define SHPC_SLOT_STATE_MASK     0x03
-#define SHPC_SLOT_STATE_SHIFT \
-    (ffs(SHPC_SLOT_STATE_MASK) - 1)
-
-#define SHPC_STATE_NO       0x0
-#define SHPC_STATE_PWRONLY  0x1
-#define SHPC_STATE_ENABLED  0x2
-#define SHPC_STATE_DISABLED 0x3
-
-#define SHPC_SLOT_PWR_LED_MASK   0xC
-#define SHPC_SLOT_PWR_LED_SHIFT \
-    (ffs(SHPC_SLOT_PWR_LED_MASK) - 1)
-#define SHPC_SLOT_ATTN_LED_MASK  0x30
-#define SHPC_SLOT_ATTN_LED_SHIFT \
-    (ffs(SHPC_SLOT_ATTN_LED_MASK) - 1)
-
-#define SHPC_LED_NO     0x0
-#define SHPC_LED_ON     0x1
-#define SHPC_LED_BLINK  0x2
-#define SHPC_LED_OFF    0x3
-
-#define SHPC_SLOT_STATUS_PWR_FAULT      0x40
-#define SHPC_SLOT_STATUS_BUTTON         0x80
-#define SHPC_SLOT_STATUS_MRL_OPEN       0x100
-#define SHPC_SLOT_STATUS_66             0x200
-#define SHPC_SLOT_STATUS_PRSNT_MASK     0xC00
-#define SHPC_SLOT_STATUS_PRSNT_EMPTY    0x3
-#define SHPC_SLOT_STATUS_PRSNT_25W      0x1
-#define SHPC_SLOT_STATUS_PRSNT_15W      0x2
-#define SHPC_SLOT_STATUS_PRSNT_7_5W     0x0
-
-#define SHPC_SLOT_STATUS_PRSNT_PCIX     0x3000
-
-
- /* 1 byte */
-#define SHPC_SLOT_EVENT_LATCH(s)        (0x2 + SHPC_SLOT_REG(s))
- /* 1 byte */
-#define SHPC_SLOT_EVENT_SERR_INT_DIS(d, s) (0x3 + SHPC_SLOT_REG(s))
-#define SHPC_SLOT_EVENT_PRESENCE        0x01
-#define SHPC_SLOT_EVENT_ISOLATED_FAULT  0x02
-#define SHPC_SLOT_EVENT_BUTTON          0x04
-#define SHPC_SLOT_EVENT_MRL             0x08
-#define SHPC_SLOT_EVENT_CONNECTED_FAULT 0x10
-/* Bits below are used for Serr/Int disable only */
-#define SHPC_SLOT_EVENT_MRL_SERR_DIS    0x20
-#define SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS 0x40
-
-#define SHPC_MIN_SLOTS        1
-#define SHPC_MAX_SLOTS        31
-#define SHPC_SIZEOF(d)    SHPC_SLOT_REG((d)->shpc->nslots)
-
-/* SHPC Slot identifiers */
-
-/* Hotplug supported at 31 slots out of the total 32.  We reserve slot 0,
-   and give the rest of them physical *and* pci numbers starting from 1, so
-   they match logical numbers.  Note: this means that multiple slots must have
-   different chassis number values, to make chassis+physical slot unique.
-   TODO: make this configurable? */
-#define SHPC_IDX_TO_LOGICAL(slot) ((slot) + 1)
-#define SHPC_LOGICAL_TO_IDX(target) ((target) - 1)
-#define SHPC_IDX_TO_PCI(slot) ((slot) + 1)
-#define SHPC_PCI_TO_IDX(pci_slot) ((pci_slot) - 1)
-#define SHPC_IDX_TO_PHYSICAL(slot) ((slot) + 1)
-
-static int roundup_pow_of_two(int x)
-{
-    x |= (x >> 1);
-    x |= (x >> 2);
-    x |= (x >> 4);
-    x |= (x >> 8);
-    x |= (x >> 16);
-    return x + 1;
-}
-
-static uint16_t shpc_get_status(SHPCDevice *shpc, int slot, uint16_t msk)
-{
-    uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot);
-    return (pci_get_word(status) & msk) >> (ffs(msk) - 1);
-}
-
-static void shpc_set_status(SHPCDevice *shpc,
-                            int slot, uint8_t value, uint16_t msk)
-{
-    uint8_t *status = shpc->config + SHPC_SLOT_STATUS(slot);
-    pci_word_test_and_clear_mask(status, msk);
-    pci_word_test_and_set_mask(status, value << (ffs(msk) - 1));
-}
-
-static void shpc_interrupt_update(PCIDevice *d)
-{
-    SHPCDevice *shpc = d->shpc;
-    int slot;
-    int level = 0;
-    uint32_t serr_int;
-    uint32_t int_locator = 0;
-
-    /* Update interrupt locator register */
-    for (slot = 0; slot < shpc->nslots; ++slot) {
-        uint8_t event = shpc->config[SHPC_SLOT_EVENT_LATCH(slot)];
-        uint8_t disable = shpc->config[SHPC_SLOT_EVENT_SERR_INT_DIS(d, slot)];
-        uint32_t mask = 1 << SHPC_IDX_TO_LOGICAL(slot);
-        if (event & ~disable) {
-            int_locator |= mask;
-        }
-    }
-    serr_int = pci_get_long(shpc->config + SHPC_SERR_INT);
-    if ((serr_int & SHPC_CMD_DETECTED) && !(serr_int & SHPC_CMD_INT_DIS)) {
-        int_locator |= SHPC_INT_COMMAND;
-    }
-    pci_set_long(shpc->config + SHPC_INT_LOCATOR, int_locator);
-    level = (!(serr_int & SHPC_INT_DIS) && int_locator) ? 1 : 0;
-    if (msi_enabled(d) && shpc->msi_requested != level)
-        msi_notify(d, 0);
-    else
-        qemu_set_irq(d->irq[0], level);
-    shpc->msi_requested = level;
-}
-
-static void shpc_set_sec_bus_speed(SHPCDevice *shpc, uint8_t speed)
-{
-    switch (speed) {
-    case SHPC_SEC_BUS_33:
-        shpc->config[SHPC_SEC_BUS] &= ~SHPC_SEC_BUS_MASK;
-        shpc->config[SHPC_SEC_BUS] |= speed;
-        break;
-    default:
-        pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS,
-                                   SHPC_CMD_STATUS_INVALID_MODE);
-    }
-}
-
-void shpc_reset(PCIDevice *d)
-{
-    SHPCDevice *shpc = d->shpc;
-    int nslots = shpc->nslots;
-    int i;
-    memset(shpc->config, 0, SHPC_SIZEOF(d));
-    pci_set_byte(shpc->config + SHPC_NSLOTS, nslots);
-    pci_set_long(shpc->config + SHPC_SLOTS_33, nslots);
-    pci_set_long(shpc->config + SHPC_SLOTS_66, 0);
-    pci_set_byte(shpc->config + SHPC_FIRST_DEV, SHPC_IDX_TO_PCI(0));
-    pci_set_word(shpc->config + SHPC_PHYS_SLOT,
-                 SHPC_IDX_TO_PHYSICAL(0) |
-                 SHPC_PHYS_NUM_UP |
-                 SHPC_PHYS_MRL |
-                 SHPC_PHYS_BUTTON);
-    pci_set_long(shpc->config + SHPC_SERR_INT, SHPC_INT_DIS |
-                 SHPC_SERR_DIS |
-                 SHPC_CMD_INT_DIS |
-                 SHPC_ARB_SERR_DIS);
-    pci_set_byte(shpc->config + SHPC_PROG_IFC, SHPC_PROG_IFC_1_0);
-    pci_set_word(shpc->config + SHPC_SEC_BUS, SHPC_SEC_BUS_33);
-    for (i = 0; i < shpc->nslots; ++i) {
-        pci_set_byte(shpc->config + SHPC_SLOT_EVENT_SERR_INT_DIS(d, i),
-                     SHPC_SLOT_EVENT_PRESENCE |
-                     SHPC_SLOT_EVENT_ISOLATED_FAULT |
-                     SHPC_SLOT_EVENT_BUTTON |
-                     SHPC_SLOT_EVENT_MRL |
-                     SHPC_SLOT_EVENT_CONNECTED_FAULT |
-                     SHPC_SLOT_EVENT_MRL_SERR_DIS |
-                     SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS);
-        if (shpc->sec_bus->devices[PCI_DEVFN(SHPC_IDX_TO_PCI(i), 0)]) {
-            shpc_set_status(shpc, i, SHPC_STATE_ENABLED, SHPC_SLOT_STATE_MASK);
-            shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_MRL_OPEN);
-            shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_7_5W,
-                            SHPC_SLOT_STATUS_PRSNT_MASK);
-            shpc_set_status(shpc, i, SHPC_LED_ON, SHPC_SLOT_PWR_LED_MASK);
-        } else {
-            shpc_set_status(shpc, i, SHPC_STATE_DISABLED, SHPC_SLOT_STATE_MASK);
-            shpc_set_status(shpc, i, 1, SHPC_SLOT_STATUS_MRL_OPEN);
-            shpc_set_status(shpc, i, SHPC_SLOT_STATUS_PRSNT_EMPTY,
-                            SHPC_SLOT_STATUS_PRSNT_MASK);
-            shpc_set_status(shpc, i, SHPC_LED_OFF, SHPC_SLOT_PWR_LED_MASK);
-        }
-        shpc_set_status(shpc, i, 0, SHPC_SLOT_STATUS_66);
-    }
-    shpc_set_sec_bus_speed(shpc, SHPC_SEC_BUS_33);
-    shpc->msi_requested = 0;
-    shpc_interrupt_update(d);
-}
-
-static void shpc_invalid_command(SHPCDevice *shpc)
-{
-    pci_word_test_and_set_mask(shpc->config + SHPC_CMD_STATUS,
-                               SHPC_CMD_STATUS_INVALID_CMD);
-}
-
-static void shpc_free_devices_in_slot(SHPCDevice *shpc, int slot)
-{
-    int devfn;
-    int pci_slot = SHPC_IDX_TO_PCI(slot);
-    for (devfn = PCI_DEVFN(pci_slot, 0);
-         devfn <= PCI_DEVFN(pci_slot, PCI_FUNC_MAX - 1);
-         ++devfn) {
-        PCIDevice *affected_dev = shpc->sec_bus->devices[devfn];
-        if (affected_dev) {
-            qdev_free(&affected_dev->qdev);
-        }
-    }
-}
-
-static void shpc_slot_command(SHPCDevice *shpc, uint8_t target,
-                              uint8_t state, uint8_t power, uint8_t attn)
-{
-    uint8_t current_state;
-    int slot = SHPC_LOGICAL_TO_IDX(target);
-    if (target < SHPC_CMD_TRGT_MIN || slot >= shpc->nslots) {
-        shpc_invalid_command(shpc);
-        return;
-    }
-    current_state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK);
-    if (current_state == SHPC_STATE_ENABLED && state == SHPC_STATE_PWRONLY) {
-        shpc_invalid_command(shpc);
-        return;
-    }
-
-    switch (power) {
-    case SHPC_LED_NO:
-        break;
-    default:
-        /* TODO: send event to monitor */
-        shpc_set_status(shpc, slot, power, SHPC_SLOT_PWR_LED_MASK);
-    }
-    switch (attn) {
-    case SHPC_LED_NO:
-        break;
-    default:
-        /* TODO: send event to monitor */
-        shpc_set_status(shpc, slot, attn, SHPC_SLOT_ATTN_LED_MASK);
-    }
-
-    if ((current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_PWRONLY) ||
-        (current_state == SHPC_STATE_DISABLED && state == SHPC_STATE_ENABLED)) {
-        shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK);
-    } else if ((current_state == SHPC_STATE_ENABLED ||
-                current_state == SHPC_STATE_PWRONLY) &&
-               state == SHPC_STATE_DISABLED) {
-        shpc_set_status(shpc, slot, state, SHPC_SLOT_STATE_MASK);
-        power = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK);
-        /* TODO: track what monitor requested. */
-        /* Look at LED to figure out whether it's ok to remove the device. */
-        if (power == SHPC_LED_OFF) {
-            shpc_free_devices_in_slot(shpc, slot);
-            shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN);
-            shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY,
-                            SHPC_SLOT_STATUS_PRSNT_MASK);
-            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
-                SHPC_SLOT_EVENT_BUTTON |
-                SHPC_SLOT_EVENT_MRL |
-                SHPC_SLOT_EVENT_PRESENCE;
-        }
-    }
-}
-
-static void shpc_command(SHPCDevice *shpc)
-{
-    uint8_t code = pci_get_byte(shpc->config + SHPC_CMD_CODE);
-    uint8_t speed;
-    uint8_t target;
-    uint8_t attn;
-    uint8_t power;
-    uint8_t state;
-    int i;
-
-    /* Clear status from the previous command. */
-    pci_word_test_and_clear_mask(shpc->config + SHPC_CMD_STATUS,
-                                 SHPC_CMD_STATUS_BUSY |
-                                 SHPC_CMD_STATUS_MRL_OPEN |
-                                 SHPC_CMD_STATUS_INVALID_CMD |
-                                 SHPC_CMD_STATUS_INVALID_MODE);
-    switch (code) {
-    case 0x00 ... 0x3f:
-        target = shpc->config[SHPC_CMD_TRGT] & SHPC_CMD_TRGT_MAX;
-        state = (code & SHPC_SLOT_STATE_MASK) >> SHPC_SLOT_STATE_SHIFT;
-        power = (code & SHPC_SLOT_PWR_LED_MASK) >> SHPC_SLOT_PWR_LED_SHIFT;
-        attn = (code & SHPC_SLOT_ATTN_LED_MASK) >> SHPC_SLOT_ATTN_LED_SHIFT;
-        shpc_slot_command(shpc, target, state, power, attn);
-        break;
-    case 0x40 ... 0x47:
-        speed = code & SHPC_SEC_BUS_MASK;
-        shpc_set_sec_bus_speed(shpc, speed);
-        break;
-    case 0x48:
-        /* Power only all slots */
-        /* first verify no slots are enabled */
-        for (i = 0; i < shpc->nslots; ++i) {
-            state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK);
-            if (state == SHPC_STATE_ENABLED) {
-                shpc_invalid_command(shpc);
-                goto done;
-            }
-        }
-        for (i = 0; i < shpc->nslots; ++i) {
-            if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) {
-                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
-                                  SHPC_STATE_PWRONLY, SHPC_LED_ON, SHPC_LED_NO);
-            } else {
-                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
-                                  SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO);
-            }
-        }
-        break;
-    case 0x49:
-        /* Enable all slots */
-        /* TODO: Spec says this shall fail if some are already enabled.
-         * This doesn't make sense - why not? a spec bug? */
-        for (i = 0; i < shpc->nslots; ++i) {
-            state = shpc_get_status(shpc, i, SHPC_SLOT_STATE_MASK);
-            if (state == SHPC_STATE_ENABLED) {
-                shpc_invalid_command(shpc);
-                goto done;
-            }
-        }
-        for (i = 0; i < shpc->nslots; ++i) {
-            if (!(shpc_get_status(shpc, i, SHPC_SLOT_STATUS_MRL_OPEN))) {
-                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
-                                  SHPC_STATE_ENABLED, SHPC_LED_ON, SHPC_LED_NO);
-            } else {
-                shpc_slot_command(shpc, i + SHPC_CMD_TRGT_MIN,
-                                  SHPC_STATE_NO, SHPC_LED_OFF, SHPC_LED_NO);
-            }
-        }
-        break;
-    default:
-        shpc_invalid_command(shpc);
-        break;
-    }
-done:
-    pci_long_test_and_set_mask(shpc->config + SHPC_SERR_INT, SHPC_CMD_DETECTED);
-}
-
-static void shpc_write(PCIDevice *d, unsigned addr, uint64_t val, int l)
-{
-    SHPCDevice *shpc = d->shpc;
-    int i;
-    if (addr >= SHPC_SIZEOF(d)) {
-        return;
-    }
-    l = MIN(l, SHPC_SIZEOF(d) - addr);
-
-    /* TODO: code duplicated from pci.c */
-    for (i = 0; i < l; val >>= 8, ++i) {
-        unsigned a = addr + i;
-        uint8_t wmask = shpc->wmask[a];
-        uint8_t w1cmask = shpc->w1cmask[a];
-        assert(!(wmask & w1cmask));
-        shpc->config[a] = (shpc->config[a] & ~wmask) | (val & wmask);
-        shpc->config[a] &= ~(val & w1cmask); /* W1C: Write 1 to Clear */
-    }
-    if (ranges_overlap(addr, l, SHPC_CMD_CODE, 2)) {
-        shpc_command(shpc);
-    }
-    shpc_interrupt_update(d);
-}
-
-static uint64_t shpc_read(PCIDevice *d, unsigned addr, int l)
-{
-    uint64_t val = 0x0;
-    if (addr >= SHPC_SIZEOF(d)) {
-        return val;
-    }
-    l = MIN(l, SHPC_SIZEOF(d) - addr);
-    memcpy(&val, d->shpc->config + addr, l);
-    return val;
-}
-
-/* SHPC Bridge Capability */
-#define SHPC_CAP_LENGTH 0x08
-#define SHPC_CAP_DWORD_SELECT 0x2 /* 1 byte */
-#define SHPC_CAP_CxP 0x3 /* 1 byte: CSP, CIP */
-#define SHPC_CAP_DWORD_DATA 0x4 /* 4 bytes */
-#define SHPC_CAP_CSP_MASK 0x4
-#define SHPC_CAP_CIP_MASK 0x8
-
-static uint8_t shpc_cap_dword(PCIDevice *d)
-{
-    return pci_get_byte(d->config + d->shpc->cap + SHPC_CAP_DWORD_SELECT);
-}
-
-/* Update dword data capability register */
-static void shpc_cap_update_dword(PCIDevice *d)
-{
-    unsigned data;
-    data = shpc_read(d, shpc_cap_dword(d) * 4, 4);
-    pci_set_long(d->config  + d->shpc->cap + SHPC_CAP_DWORD_DATA, data);
-}
-
-/* Add SHPC capability to the config space for the device. */
-static int shpc_cap_add_config(PCIDevice *d)
-{
-    uint8_t *config;
-    int config_offset;
-    config_offset = pci_add_capability(d, PCI_CAP_ID_SHPC,
-                                       0, SHPC_CAP_LENGTH);
-    if (config_offset < 0) {
-        return config_offset;
-    }
-    config = d->config + config_offset;
-
-    pci_set_byte(config + SHPC_CAP_DWORD_SELECT, 0);
-    pci_set_byte(config + SHPC_CAP_CxP, 0);
-    pci_set_long(config + SHPC_CAP_DWORD_DATA, 0);
-    d->shpc->cap = config_offset;
-    /* Make dword select and data writeable. */
-    pci_set_byte(d->wmask + config_offset + SHPC_CAP_DWORD_SELECT, 0xff);
-    pci_set_long(d->wmask + config_offset + SHPC_CAP_DWORD_DATA, 0xffffffff);
-    return 0;
-}
-
-static uint64_t shpc_mmio_read(void *opaque, hwaddr addr,
-                               unsigned size)
-{
-    return shpc_read(opaque, addr, size);
-}
-
-static void shpc_mmio_write(void *opaque, hwaddr addr,
-                            uint64_t val, unsigned size)
-{
-    shpc_write(opaque, addr, val, size);
-}
-
-static const MemoryRegionOps shpc_mmio_ops = {
-    .read = shpc_mmio_read,
-    .write = shpc_mmio_write,
-    .endianness = DEVICE_LITTLE_ENDIAN,
-    .valid = {
-        /* SHPC ECN requires dword accesses, but the original 1.0 spec doesn't.
-         * It's easier to suppport all sizes than worry about it. */
-        .min_access_size = 1,
-        .max_access_size = 4,
-    },
-};
-
-static int shpc_device_hotplug(DeviceState *qdev, PCIDevice *affected_dev,
-                               PCIHotplugState hotplug_state)
-{
-    int pci_slot = PCI_SLOT(affected_dev->devfn);
-    uint8_t state;
-    uint8_t led;
-    PCIDevice *d = DO_UPCAST(PCIDevice, qdev, qdev);
-    SHPCDevice *shpc = d->shpc;
-    int slot = SHPC_PCI_TO_IDX(pci_slot);
-    if (pci_slot < SHPC_IDX_TO_PCI(0) || slot >= shpc->nslots) {
-        error_report("Unsupported PCI slot %d for standard hotplug "
-                     "controller. Valid slots are between %d and %d.",
-                     pci_slot, SHPC_IDX_TO_PCI(0),
-                     SHPC_IDX_TO_PCI(shpc->nslots) - 1);
-        return -1;
-    }
-    /* Don't send event when device is enabled during qemu machine creation:
-     * it is present on boot, no hotplug event is necessary. We do send an
-     * event when the device is disabled later. */
-    if (hotplug_state == PCI_COLDPLUG_ENABLED) {
-        shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN);
-        shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W,
-                        SHPC_SLOT_STATUS_PRSNT_MASK);
-        return 0;
-    }
-    if (hotplug_state == PCI_HOTPLUG_DISABLED) {
-        shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |= SHPC_SLOT_EVENT_BUTTON;
-        state = shpc_get_status(shpc, slot, SHPC_SLOT_STATE_MASK);
-        led = shpc_get_status(shpc, slot, SHPC_SLOT_PWR_LED_MASK);
-        if (state == SHPC_STATE_DISABLED && led == SHPC_LED_OFF) {
-            shpc_free_devices_in_slot(shpc, slot);
-            shpc_set_status(shpc, slot, 1, SHPC_SLOT_STATUS_MRL_OPEN);
-            shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_EMPTY,
-                            SHPC_SLOT_STATUS_PRSNT_MASK);
-            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
-                SHPC_SLOT_EVENT_MRL |
-                SHPC_SLOT_EVENT_PRESENCE;
-        }
-    } else {
-        /* This could be a cancellation of the previous removal.
-         * We check MRL state to figure out. */
-        if (shpc_get_status(shpc, slot, SHPC_SLOT_STATUS_MRL_OPEN)) {
-            shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_MRL_OPEN);
-            shpc_set_status(shpc, slot, SHPC_SLOT_STATUS_PRSNT_7_5W,
-                            SHPC_SLOT_STATUS_PRSNT_MASK);
-            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
-                SHPC_SLOT_EVENT_BUTTON |
-                SHPC_SLOT_EVENT_MRL |
-                SHPC_SLOT_EVENT_PRESENCE;
-        } else {
-            /* Press attention button to cancel removal */
-            shpc->config[SHPC_SLOT_EVENT_LATCH(slot)] |=
-                SHPC_SLOT_EVENT_BUTTON;
-        }
-    }
-    shpc_set_status(shpc, slot, 0, SHPC_SLOT_STATUS_66);
-    shpc_interrupt_update(d);
-    return 0;
-}
-
-/* Initialize the SHPC structure in bridge's BAR. */
-int shpc_init(PCIDevice *d, PCIBus *sec_bus, MemoryRegion *bar, unsigned offset)
-{
-    int i, ret;
-    int nslots = SHPC_MAX_SLOTS; /* TODO: qdev property? */
-    SHPCDevice *shpc = d->shpc = g_malloc0(sizeof(*d->shpc));
-    shpc->sec_bus = sec_bus;
-    ret = shpc_cap_add_config(d);
-    if (ret) {
-        g_free(d->shpc);
-        return ret;
-    }
-    if (nslots < SHPC_MIN_SLOTS) {
-        return 0;
-    }
-    if (nslots > SHPC_MAX_SLOTS ||
-        SHPC_IDX_TO_PCI(nslots) > PCI_SLOT_MAX) {
-        /* TODO: report an error mesage that makes sense. */
-        return -EINVAL;
-    }
-    shpc->nslots = nslots;
-    shpc->config = g_malloc0(SHPC_SIZEOF(d));
-    shpc->cmask = g_malloc0(SHPC_SIZEOF(d));
-    shpc->wmask = g_malloc0(SHPC_SIZEOF(d));
-    shpc->w1cmask = g_malloc0(SHPC_SIZEOF(d));
-
-    shpc_reset(d);
-
-    pci_set_long(shpc->config + SHPC_BASE_OFFSET, offset);
-
-    pci_set_byte(shpc->wmask + SHPC_CMD_CODE, 0xff);
-    pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX);
-    pci_set_byte(shpc->wmask + SHPC_CMD_TRGT, SHPC_CMD_TRGT_MAX);
-    pci_set_long(shpc->wmask + SHPC_SERR_INT,
-                 SHPC_INT_DIS |
-                 SHPC_SERR_DIS |
-                 SHPC_CMD_INT_DIS |
-                 SHPC_ARB_SERR_DIS);
-    pci_set_long(shpc->w1cmask + SHPC_SERR_INT,
-                 SHPC_CMD_DETECTED |
-                 SHPC_ARB_DETECTED);
-    for (i = 0; i < nslots; ++i) {
-        pci_set_byte(shpc->wmask +
-                     SHPC_SLOT_EVENT_SERR_INT_DIS(d, i),
-                     SHPC_SLOT_EVENT_PRESENCE |
-                     SHPC_SLOT_EVENT_ISOLATED_FAULT |
-                     SHPC_SLOT_EVENT_BUTTON |
-                     SHPC_SLOT_EVENT_MRL |
-                     SHPC_SLOT_EVENT_CONNECTED_FAULT |
-                     SHPC_SLOT_EVENT_MRL_SERR_DIS |
-                     SHPC_SLOT_EVENT_CONNECTED_FAULT_SERR_DIS);
-        pci_set_byte(shpc->w1cmask +
-                     SHPC_SLOT_EVENT_LATCH(i),
-                     SHPC_SLOT_EVENT_PRESENCE |
-                     SHPC_SLOT_EVENT_ISOLATED_FAULT |
-                     SHPC_SLOT_EVENT_BUTTON |
-                     SHPC_SLOT_EVENT_MRL |
-                     SHPC_SLOT_EVENT_CONNECTED_FAULT);
-    }
-
-    /* TODO: init cmask */
-    memory_region_init_io(&shpc->mmio, &shpc_mmio_ops, d, "shpc-mmio",
-                          SHPC_SIZEOF(d));
-    shpc_cap_update_dword(d);
-    memory_region_add_subregion(bar, offset, &shpc->mmio);
-    pci_bus_hotplug(sec_bus, shpc_device_hotplug, &d->qdev);
-
-    d->cap_present |= QEMU_PCI_CAP_SHPC;
-    return 0;
-}
-
-int shpc_bar_size(PCIDevice *d)
-{
-    return roundup_pow_of_two(SHPC_SLOT_REG(SHPC_MAX_SLOTS));
-}
-
-void shpc_cleanup(PCIDevice *d, MemoryRegion *bar)
-{
-    SHPCDevice *shpc = d->shpc;
-    d->cap_present &= ~QEMU_PCI_CAP_SHPC;
-    memory_region_del_subregion(bar, &shpc->mmio);
-    /* TODO: cleanup config space changes? */
-    g_free(shpc->config);
-    g_free(shpc->cmask);
-    g_free(shpc->wmask);
-    g_free(shpc->w1cmask);
-    memory_region_destroy(&shpc->mmio);
-    g_free(shpc);
-}
-
-void shpc_cap_write_config(PCIDevice *d, uint32_t addr, uint32_t val, int l)
-{
-    if (!ranges_overlap(addr, l, d->shpc->cap, SHPC_CAP_LENGTH)) {
-        return;
-    }
-    if (ranges_overlap(addr, l, d->shpc->cap + SHPC_CAP_DWORD_DATA, 4)) {
-        unsigned dword_data;
-        dword_data = pci_get_long(d->shpc->config + d->shpc->cap
-                                  + SHPC_CAP_DWORD_DATA);
-        shpc_write(d, shpc_cap_dword(d) * 4, dword_data, 4);
-    }
-    /* Update cap dword data in case guest is going to read it. */
-    shpc_cap_update_dword(d);
-}
-
-static void shpc_save(QEMUFile *f, void *pv, size_t size)
-{
-    PCIDevice *d = container_of(pv, PCIDevice, shpc);
-    qemu_put_buffer(f, d->shpc->config, SHPC_SIZEOF(d));
-}
-
-static int shpc_load(QEMUFile *f, void *pv, size_t size)
-{
-    PCIDevice *d = container_of(pv, PCIDevice, shpc);
-    int ret = qemu_get_buffer(f, d->shpc->config, SHPC_SIZEOF(d));
-    if (ret != SHPC_SIZEOF(d)) {
-        return -EINVAL;
-    }
-    /* Make sure we don't lose notifications. An extra interrupt is harmless. */
-    d->shpc->msi_requested = 0;
-    shpc_interrupt_update(d);
-    return 0;
-}
-
-VMStateInfo shpc_vmstate_info = {
-    .name = "shpc",
-    .get  = shpc_load,
-    .put  = shpc_save,
-};