hw: move target-independent files to subdirectories

This patch tackles all files that are compiled once, moving
them to subdirectories of hw/.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

1 files changed, 274 insertions, 0 deletions

diff --git a/hw/sd/ssi-sd.c b/hw/sd/ssi-sd.c
new file mode 100644
index 0000000..4d3c4f6
--- /dev/null
+++ b/hw/sd/ssi-sd.c
@@ -0,0 +1,274 @@
+/*
+ * SSI to SD card adapter.
+ *
+ * Copyright (c) 2007-2009 CodeSourcery.
+ * Written by Paul Brook
+ *
+ * This code is licensed under the GNU GPL v2.
+ *
+ * Contributions after 2012-01-13 are licensed under the terms of the
+ * GNU GPL, version 2 or (at your option) any later version.
+ */
+
+#include "sysemu/blockdev.h"
+#include "hw/ssi.h"
+#include "hw/sd.h"
+
+//#define DEBUG_SSI_SD 1
+
+#ifdef DEBUG_SSI_SD
+#define DPRINTF(fmt, ...) \
+do { printf("ssi_sd: " fmt , ## __VA_ARGS__); } while (0)
+#define BADF(fmt, ...) \
+do { fprintf(stderr, "ssi_sd: error: " fmt , ## __VA_ARGS__); exit(1);} while (0)
+#else
+#define DPRINTF(fmt, ...) do {} while(0)
+#define BADF(fmt, ...) \
+do { fprintf(stderr, "ssi_sd: error: " fmt , ## __VA_ARGS__);} while (0)
+#endif
+
+typedef enum {
+    SSI_SD_CMD,
+    SSI_SD_CMDARG,
+    SSI_SD_RESPONSE,
+    SSI_SD_DATA_START,
+    SSI_SD_DATA_READ,
+} ssi_sd_mode;
+
+typedef struct {
+    SSISlave ssidev;
+    ssi_sd_mode mode;
+    int cmd;
+    uint8_t cmdarg[4];
+    uint8_t response[5];
+    int arglen;
+    int response_pos;
+    int stopping;
+    SDState *sd;
+} ssi_sd_state;
+
+/* State word bits.  */
+#define SSI_SDR_LOCKED          0x0001
+#define SSI_SDR_WP_ERASE        0x0002
+#define SSI_SDR_ERROR           0x0004
+#define SSI_SDR_CC_ERROR        0x0008
+#define SSI_SDR_ECC_FAILED      0x0010
+#define SSI_SDR_WP_VIOLATION    0x0020
+#define SSI_SDR_ERASE_PARAM     0x0040
+#define SSI_SDR_OUT_OF_RANGE    0x0080
+#define SSI_SDR_IDLE            0x0100
+#define SSI_SDR_ERASE_RESET     0x0200
+#define SSI_SDR_ILLEGAL_COMMAND 0x0400
+#define SSI_SDR_COM_CRC_ERROR   0x0800
+#define SSI_SDR_ERASE_SEQ_ERROR 0x1000
+#define SSI_SDR_ADDRESS_ERROR   0x2000
+#define SSI_SDR_PARAMETER_ERROR 0x4000
+
+static uint32_t ssi_sd_transfer(SSISlave *dev, uint32_t val)
+{
+    ssi_sd_state *s = FROM_SSI_SLAVE(ssi_sd_state, dev);
+
+    /* Special case: allow CMD12 (STOP TRANSMISSION) while reading data.  */
+    if (s->mode == SSI_SD_DATA_READ && val == 0x4d) {
+        s->mode = SSI_SD_CMD;
+        /* There must be at least one byte delay before the card responds.  */
+        s->stopping = 1;
+    }
+
+    switch (s->mode) {
+    case SSI_SD_CMD:
+        if (val == 0xff) {
+            DPRINTF("NULL command\n");
+            return 0xff;
+        }
+        s->cmd = val & 0x3f;
+        s->mode = SSI_SD_CMDARG;
+        s->arglen = 0;
+        return 0xff;
+    case SSI_SD_CMDARG:
+        if (s->arglen == 4) {
+            SDRequest request;
+            uint8_t longresp[16];
+            /* FIXME: Check CRC.  */
+            request.cmd = s->cmd;
+            request.arg = (s->cmdarg[0] << 24) | (s->cmdarg[1] << 16)
+                           | (s->cmdarg[2] << 8) | s->cmdarg[3];
+            DPRINTF("CMD%d arg 0x%08x\n", s->cmd, request.arg);
+            s->arglen = sd_do_command(s->sd, &request, longresp);
+            if (s->arglen <= 0) {
+                s->arglen = 1;
+                s->response[0] = 4;
+                DPRINTF("SD command failed\n");
+            } else if (s->cmd == 58) {
+                /* CMD58 returns R3 response (OCR)  */
+                DPRINTF("Returned OCR\n");
+                s->arglen = 5;
+                s->response[0] = 1;
+                memcpy(&s->response[1], longresp, 4);
+            } else if (s->arglen != 4) {
+                BADF("Unexpected response to cmd %d\n", s->cmd);
+                /* Illegal command is about as near as we can get.  */
+                s->arglen = 1;
+                s->response[0] = 4;
+            } else {
+                /* All other commands return status.  */
+                uint32_t cardstatus;
+                uint16_t status;
+                /* CMD13 returns a 2-byte statuse work. Other commands
+                   only return the first byte.  */
+                s->arglen = (s->cmd == 13) ? 2 : 1;
+                cardstatus = (longresp[0] << 24) | (longresp[1] << 16)
+                             | (longresp[2] << 8) | longresp[3];
+                status = 0;
+                if (((cardstatus >> 9) & 0xf) < 4)
+                    status |= SSI_SDR_IDLE;
+                if (cardstatus & ERASE_RESET)
+                    status |= SSI_SDR_ERASE_RESET;
+                if (cardstatus & ILLEGAL_COMMAND)
+                    status |= SSI_SDR_ILLEGAL_COMMAND;
+                if (cardstatus & COM_CRC_ERROR)
+                    status |= SSI_SDR_COM_CRC_ERROR;
+                if (cardstatus & ERASE_SEQ_ERROR)
+                    status |= SSI_SDR_ERASE_SEQ_ERROR;
+                if (cardstatus & ADDRESS_ERROR)
+                    status |= SSI_SDR_ADDRESS_ERROR;
+                if (cardstatus & CARD_IS_LOCKED)
+                    status |= SSI_SDR_LOCKED;
+                if (cardstatus & (LOCK_UNLOCK_FAILED | WP_ERASE_SKIP))
+                    status |= SSI_SDR_WP_ERASE;
+                if (cardstatus & SD_ERROR)
+                    status |= SSI_SDR_ERROR;
+                if (cardstatus & CC_ERROR)
+                    status |= SSI_SDR_CC_ERROR;
+                if (cardstatus & CARD_ECC_FAILED)
+                    status |= SSI_SDR_ECC_FAILED;
+                if (cardstatus & WP_VIOLATION)
+                    status |= SSI_SDR_WP_VIOLATION;
+                if (cardstatus & ERASE_PARAM)
+                    status |= SSI_SDR_ERASE_PARAM;
+                if (cardstatus & (OUT_OF_RANGE | CID_CSD_OVERWRITE))
+                    status |= SSI_SDR_OUT_OF_RANGE;
+                /* ??? Don't know what Parameter Error really means, so
+                   assume it's set if the second byte is nonzero.  */
+                if (status & 0xff)
+                    status |= SSI_SDR_PARAMETER_ERROR;
+                s->response[0] = status >> 8;
+                s->response[1] = status;
+                DPRINTF("Card status 0x%02x\n", status);
+            }
+            s->mode = SSI_SD_RESPONSE;
+            s->response_pos = 0;
+        } else {
+            s->cmdarg[s->arglen++] = val;
+        }
+        return 0xff;
+    case SSI_SD_RESPONSE:
+        if (s->stopping) {
+            s->stopping = 0;
+            return 0xff;
+        }
+        if (s->response_pos < s->arglen) {
+            DPRINTF("Response 0x%02x\n", s->response[s->response_pos]);
+            return s->response[s->response_pos++];
+        }
+        if (sd_data_ready(s->sd)) {
+            DPRINTF("Data read\n");
+            s->mode = SSI_SD_DATA_START;
+        } else {
+            DPRINTF("End of command\n");
+            s->mode = SSI_SD_CMD;
+        }
+        return 0xff;
+    case SSI_SD_DATA_START:
+        DPRINTF("Start read block\n");
+        s->mode = SSI_SD_DATA_READ;
+        return 0xfe;
+    case SSI_SD_DATA_READ:
+        val = sd_read_data(s->sd);
+        if (!sd_data_ready(s->sd)) {
+            DPRINTF("Data read end\n");
+            s->mode = SSI_SD_CMD;
+        }
+        return val;
+    }
+    /* Should never happen.  */
+    return 0xff;
+}
+
+static void ssi_sd_save(QEMUFile *f, void *opaque)
+{
+    SSISlave *ss = SSI_SLAVE(opaque);
+    ssi_sd_state *s = (ssi_sd_state *)opaque;
+    int i;
+
+    qemu_put_be32(f, s->mode);
+    qemu_put_be32(f, s->cmd);
+    for (i = 0; i < 4; i++)
+        qemu_put_be32(f, s->cmdarg[i]);
+    for (i = 0; i < 5; i++)
+        qemu_put_be32(f, s->response[i]);
+    qemu_put_be32(f, s->arglen);
+    qemu_put_be32(f, s->response_pos);
+    qemu_put_be32(f, s->stopping);
+
+    qemu_put_be32(f, ss->cs);
+}
+
+static int ssi_sd_load(QEMUFile *f, void *opaque, int version_id)
+{
+    SSISlave *ss = SSI_SLAVE(opaque);
+    ssi_sd_state *s = (ssi_sd_state *)opaque;
+    int i;
+
+    if (version_id != 1)
+        return -EINVAL;
+
+    s->mode = qemu_get_be32(f);
+    s->cmd = qemu_get_be32(f);
+    for (i = 0; i < 4; i++)
+        s->cmdarg[i] = qemu_get_be32(f);
+    for (i = 0; i < 5; i++)
+        s->response[i] = qemu_get_be32(f);
+    s->arglen = qemu_get_be32(f);
+    s->response_pos = qemu_get_be32(f);
+    s->stopping = qemu_get_be32(f);
+
+    ss->cs = qemu_get_be32(f);
+
+    return 0;
+}
+
+static int ssi_sd_init(SSISlave *dev)
+{
+    ssi_sd_state *s = FROM_SSI_SLAVE(ssi_sd_state, dev);
+    DriveInfo *dinfo;
+
+    s->mode = SSI_SD_CMD;
+    dinfo = drive_get_next(IF_SD);
+    s->sd = sd_init(dinfo ? dinfo->bdrv : NULL, 1);
+    register_savevm(&dev->qdev, "ssi_sd", -1, 1, ssi_sd_save, ssi_sd_load, s);
+    return 0;
+}
+
+static void ssi_sd_class_init(ObjectClass *klass, void *data)
+{
+    SSISlaveClass *k = SSI_SLAVE_CLASS(klass);
+
+    k->init = ssi_sd_init;
+    k->transfer = ssi_sd_transfer;
+    k->cs_polarity = SSI_CS_LOW;
+}
+
+static const TypeInfo ssi_sd_info = {
+    .name          = "ssi-sd",
+    .parent        = TYPE_SSI_SLAVE,
+    .instance_size = sizeof(ssi_sd_state),
+    .class_init    = ssi_sd_class_init,
+};
+
+static void ssi_sd_register_types(void)
+{
+    type_register_static(&ssi_sd_info);
+}
+
+type_init(ssi_sd_register_types)