nbd-client: Refuse read-only client with BDRV_O_RDWR

The NBD spec says that clients should not try to write/trim to
an export advertised as read-only by the server.  But we failed
to check that, and would allow the block layer to use NBD with
BDRV_O_RDWR even when the server is read-only, which meant we
were depending on the server sending a proper EPERM failure for
various commands, and also exposes a leaky abstraction: using
qemu-io in read-write mode would succeed on 'w -z 0 0' because
of local short-circuiting logic, but 'w 0 0' would send a
request over the wire (where it then depends on the server, and
fails at least for qemu-nbd but might pass for other NBD
implementations).

With this patch, a client MUST request read-only mode to access
a server that is doing a read-only export, or else it will get
a message like:

can't open device nbd://localhost:10809/foo: request for write access conflicts with read-only export

It is no longer possible to even attempt writes over the wire
(including the corner case of 0-length writes), because the block
layer enforces the explicit read-only request; this matches the
behavior of qcow2 when backed by a read-only POSIX file.

Fix several iotests to comply with the new behavior (since
qemu-nbd of an internal snapshot, as well as nbd-server-add over QMP,
default to a read-only export, we must tell blockdev-add/qemu-io to
set up a read-only client).

CC: qemu-stable@nongnu.org
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20171108215703.9295-3-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>

1 files changed, 9 insertions, 0 deletions

diff --git a/block/nbd-client.c b/block/nbd-client.c
index de6c153..daa4392 100644
--- a/block/nbd-client.c
+++ b/block/nbd-client.c
@@ -697,6 +697,7 @@ int nbd_client_co_pwritev(BlockDriverState *bs, uint64_t offset,
         .len = bytes,
     };
 
+    assert(!(client->info.flags & NBD_FLAG_READ_ONLY));
     if (flags & BDRV_REQ_FUA) {
         assert(client->info.flags & NBD_FLAG_SEND_FUA);
         request.flags |= NBD_CMD_FLAG_FUA;
@@ -717,6 +718,7 @@ int nbd_client_co_pwrite_zeroes(BlockDriverState *bs, int64_t offset,
         .len = bytes,
     };
 
+    assert(!(client->info.flags & NBD_FLAG_READ_ONLY));
     if (!(client->info.flags & NBD_FLAG_SEND_WRITE_ZEROES)) {
         return -ENOTSUP;
     }
@@ -756,6 +758,7 @@ int nbd_client_co_pdiscard(BlockDriverState *bs, int64_t offset, int bytes)
         .len = bytes,
     };
 
+    assert(!(client->info.flags & NBD_FLAG_READ_ONLY));
     if (!(client->info.flags & NBD_FLAG_SEND_TRIM)) {
         return 0;
     }
@@ -814,6 +817,12 @@ int nbd_client_init(BlockDriverState *bs,
         logout("Failed to negotiate with the NBD server\n");
         return ret;
     }
+    if (client->info.flags & NBD_FLAG_READ_ONLY &&
+        !bdrv_is_read_only(bs)) {
+        error_setg(errp,
+                   "request for write access conflicts with read-only export");
+        return -EACCES;
+    }
     if (client->info.flags & NBD_FLAG_SEND_FUA) {
         bs->supported_write_flags = BDRV_REQ_FUA;
         bs->supported_zero_flags |= BDRV_REQ_FUA;