configure: Fix test for supported host CPU type

The test for whether the host CPU is supported had several problems:
 * the attempt to fall back to TCI was done as a duplicate
   test, very late (so "--cpu foo" would fail early but "--cpu unicore32"
   would fail late, differently, and after configure had already
   printed a lot of output)
 * a number of CPUs only supported as guests were included in the
   list of CPUs we would accept as valid hosts, which would result
   in a late compile failure on those systems rather than a
   configure failure or fallback to TCI
 * bailing out for an unsupported CPU happened before the main
   option parsing, so "configure --help" wouldn't work

Fix these by folding the setting of ARCH into the first test for
supported host CPU, removing spurious guest-only CPU names from it,
and moving the "fall back to TCI" code earlier.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>

1 files changed, 21 insertions, 23 deletions

diff --git a/configure b/configure
index af19391..a1394eb 100755
--- a/configure
+++ b/configure
@@ -300,8 +300,11 @@ else
   cpu=`uname -m`
 fi
 
+ARCH=
+# Normalise host CPU name and set ARCH.
+# Note that this case should only have supported host CPUs, not guests.
 case "$cpu" in
-  alpha|cris|ia64|lm32|m68k|microblaze|ppc|ppc64|sparc64|unicore32)
+  ia64|ppc|ppc64|s390|s390x|sparc64)
     cpu="$cpu"
   ;;
   i386|i486|i586|i686|i86pc|BePC)
@@ -319,20 +322,17 @@ case "$cpu" in
   mips*)
     cpu="mips"
   ;;
-  s390)
-    cpu="s390"
-  ;;
-  s390x)
-    cpu="s390x"
-  ;;
   sparc|sun4[cdmuv])
     cpu="sparc"
   ;;
   *)
-    echo "Unsupported CPU = $cpu"
-    exit 1
+    # This will result in either an error or falling back to TCI later
+    ARCH=unknown
   ;;
 esac
+if test -z "$ARCH"; then
+  ARCH="$cpu"
+fi
 
 # OS specific
 if check_define __linux__ ; then
@@ -1080,6 +1080,18 @@ echo "NOTE: The object files are built at the place where configure is launched"
 exit 1
 fi
 
+# Now we have handled --enable-tcg-interpreter and know we're not just
+# printing the help message, bail out if the host CPU isn't supported.
+if test "$ARCH" = "unknown"; then
+    if test "$tcg_interpreter" = "yes" ; then
+        echo "Unsupported CPU = $cpu, will use TCG with TCI (experimental)"
+        ARCH=tci
+    else
+        echo "Unsupported CPU = $cpu, try --enable-tcg-interpreter"
+        exit 1
+    fi
+fi
+
 # check that the C compiler works.
 cat > $TMPC <<EOF
 int main(void) { return 0; }
@@ -2903,20 +2915,6 @@ echo "sysconfdir=$sysconfdir" >> $config_host_mak
 echo "docdir=$docdir" >> $config_host_mak
 echo "confdir=$confdir" >> $config_host_mak
 
-case "$cpu" in
-  i386|x86_64|alpha|arm|cris|hppa|ia64|lm32|m68k|microblaze|mips|mips64|ppc|ppc64|s390|s390x|sparc|sparc64|unicore32)
-    ARCH=$cpu
-  ;;
-  *)
-    if test "$tcg_interpreter" = "yes" ; then
-        echo "Unsupported CPU = $cpu, will use TCG with TCI (experimental)"
-        ARCH=tci
-    else
-        echo "Unsupported CPU = $cpu, try --enable-tcg-interpreter"
-        exit 1
-    fi
-  ;;
-esac
 echo "ARCH=$ARCH" >> $config_host_mak
 if test "$debug_tcg" = "yes" ; then
   echo "CONFIG_DEBUG_TCG=y" >> $config_host_mak