path: root/sim/mips/ChangeLog

Thu Nov 20 19:56:22 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (signal_exception): Report internal errors with SIGABRT
 	not SIGQUIT.

	* sim-main.h (C0_CONFIG): New register.
	(signal.h): No longer include.

	* interp.c (decode_coproc): Allow access C0_CONFIG to register.

Tue Nov 18 15:33:48 1997  Doug Evans  <devans@canuck.cygnus.com>

	* Makefile.in (SIM_OBJS): Use $(SIM_NEW_COMMON_OBJS).

Fri Nov 14 11:56:48 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* mips.igen: Tag vr5000 instructions.
	(ANDI): Was missing mipsIV model, fix assembler syntax.
	(do_c_cond_fmt): New function.
	(C.cond.fmt): Handle mips I-III which do not support CC field
 	separatly.
	(bc1): Handle mips IV which do not have a delaed FCC separatly.
	(SDR): Mask paddr when BigEndianMem, not the converse as specified
 	in IV3.2 spec.
	(DMULT, DMULTU): Force use of hosts 64bit multiplication.  Handle
 	vr5000 which saves LO in a GPR separatly.
	
	* configure.in (enable-sim-igen): For vr5000, select vr5000
 	specific instructions.
	* configure: Re-generate.
	
Wed Nov 12 14:42:52 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (SIM_OBJS): Add sim-fpu module.

	* interp.c (store_fpr), sim-main.h: Add separate fmt_uninterpreted_32 and
 	fmt_uninterpreted_64 bit cases to switch.  Convert to
 	fmt_formatted,

	* sim-main.h (ENGINE_ISSUE_PREFIX_HOOK): Define,

	* mips.igen (SWR): Mask paddr when BigEndianMem, not the converse
 	as specified in IV3.2 spec.
	(MTC1, DMTC1): Call StoreFPR to store the GPR in the FPR.

Tue Nov 11 12:38:23 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* mips.igen: Delay slot branches add OFFSET to NIA not CIA.
 	(MFC0, MTC0, SWC1, LWC1, SDC1, LDC1): Implement.
	(start-sanitize-r5900):
	(LWXC1, SWXC1): Delete from r5900 instruction set.
	(end-sanitize-r5900):
	(MTC1, MFC1, DMTC1, DMFC1, CFC1, CTC1): Implement separate non
 	PENDING_FILL versions of instructions.  Simplify.
	(X): New function.
	(MULT, MULTU): Implement separate RD==0 and RD!=0 versions of
 	instructions.
	(BEQZ, ..., SLT, SLTI, TLT, TLE, TLI, ...): Explicitly cast GPR to
 	a signed value.
	(MTHI, MFHI): Disable code checking HI-LO.
	
	* sim-main.h (dotrace,tracefh), interp.c: Make dotrace & tracefh
 	global.
	(NULLIFY_NEXT_INSTRUCTION): Call dotrace.

Thu Nov  6 16:36:35 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_mips16_operands): Replace IPC with cia.

	* interp.c (sim_monitor, signal_exception, cache_op, store_fpr,
 	value_fpr, cop_ld, cop_lw, cop_sw, cop_sd, decode_coproc): Replace
 	IPC to `cia'.
	(UndefinedResult): Replace function with macro/function
 	combination.
	(sim_engine_run): Don't save PC in IPC.

	* sim-main.h (IPC): Delete.

	start-sanitize-vr5400
	* vr5400.igen (vr): Add missing cia argument to value_fpr.
	(do_select): Rename function select.
	end-sanitize-vr5400

	* interp.c (signal_exception, store_word, load_word,
 	address_translation, load_memory, store_memory, cache_op,
 	prefetch, sync_operation, ifetch, value_fpr, store_fpr, convert,
 	cop_lw, cop_ld, cop_sw, cop_sd, decode_coproc, sim_monitor): Add
 	current instruction address - cia - argument.
	(sim_read, sim_write): Call address_translation directly.
	(sim_engine_run): Rename variable vaddr to cia.
	(signal_exception): Pass cia to sim_monitor
	
	* sim-main.h (SignalException, LoadWord, StoreWord, CacheOp,
 	Prefetch, SyncOperation, ValueFPR, StoreFPR, Convert, COP_LW,
 	COP_LD, COP_SW, COP_SD, DecodeCoproc): Update.

	* sim-main.h (SignalExceptionSimulatorFault): Delete definition.
  	* interp.c (sim_open): Replace SignalExceptionSimulatorFault with
 	SIM_ASSERT.
	
	* interp.c (signal_exception): Pass restart address to
 	sim_engine_restart.

	* Makefile.in (semantics.o, engine.o, support.o, itable.o,
 	idecode.o): Add dependency.

	* sim-main.h (SIM_ENGINE_HALT_HOOK, SIM_ENGINE_RESUME_HOOK):
 	Delete definitions
	(DELAY_SLOT): Update NIA not PC with branch address.
	(NULLIFY_NEXT_INSTRUCTION): Set NIA to instruction after next.

	* mips.igen: Use CIA not PC in branch calculations.
	(illegal): Call SignalException.
 	(BEQ, ADDIU): Fix assembler.

Wed Nov  5 12:19:56 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* m16.igen (JALX): Was missing.

	* configure.in (enable-sim-igen): New configuration option.
	* configure: Re-generate.
	
	* sim-main.h (MAX_INSNS, INSN_NAME): Define.

	* interp.c (load_memory, store_memory): Delete parameter RAW.
	(sim_read, sim_write): Use sim_core_{read,write}_buffer directly
 	bypassing {load,store}_memory.

	* sim-main.h (ByteSwapMem): Delete definition.

	* Makefile.in (SIM_OBJS): Add sim-memopt module.

	* interp.c (sim_do_command, sim_commands): Delete mips specific
 	commands.  Handled by module sim-options.
		
	* sim-main.h (SIM_HAVE_FLATMEM): Undefine, use sim-core.o module.
	(WITH_MODULO_MEMORY): Define.

	* interp.c (sim_info): Delete code printing memory size.

	* interp.c (mips_size): Nee sim_size, delete function.
	(power2): Delete.
	(monitor, monitor_base, monitor_size): Delete global variables.
	(sim_open, sim_close): Delete code creating monitor and other
 	memory regions.  Use sim-memopts module, via sim_do_commandf, to
 	manage memory regions.
	(load_memory, store_memory): Use sim-core for memory model.
	
	* interp.c (address_translation): Delete all memory map code
 	except line forcing 32 bit addresses.

Wed Nov  5 11:21:11 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* sim-main.h (WITH_TRACE): Delete definition.  Enables common
 	trace options.

	* interp.c (logfh, logfile): Delete globals.
	(sim_open, sim_close): Delete code opening & closing log file.
	(mips_option_handler): Delete -l and -n options.
	(OPTION mips_options): Ditto.

	* interp.c (OPTION mips_options): Rename option trace to dinero.
	(mips_option_handler): Update.

Wed Nov  5 09:35:59 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (fetch_str): New function.
	(sim_monitor): Rewrite using sim_read & sim_write.
	(sim_open): Check magic number.
	(sim_open): Write monitor vectors into memory using sim_write.
	(MONITOR_BASE, MONITOR_SIZE, MEM_SIZE): Define.
	(sim_read, sim_write): Simplify - transfer data one byte at a
 	time.
	(load_memory, store_memory): Clarify meaning of parameter RAW.

	* sim-main.h (isHOST): Defete definition.
	(isTARGET): Mark as depreciated.
	(address_translation): Delete parameter HOST.

	* interp.c (address_translation): Delete parameter HOST.

start-sanitize-tx49
Wed Oct 29 14:21:32 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c: Add tx49 configury and insns.
	* configure.in: Add tx49 configury.
	* configure: Update.

end-sanitize-tx49
Wed Oct 29 11:13:56 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* mips.igen: 

	* Makefile.in (IGEN_INCLUDE): Files included by mips.igen.
	(tmp-igen, tmp-m16): Depend on IGEN_INCLUDE.

Tue Oct 28 11:06:47 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* mips.igen: Add model filter field to records.

Mon Oct 27 17:53:59 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (SIM_NO_CFLAGS): Define.  Define WITH_IGEN=0.
	
	interp.c (sim_engine_run): Do not compile function sim_engine_run
 	when WITH_IGEN == 1.

	* configure.in (sim_igen_flags, sim_m16_flags): Set according to
 	target architecture.

	Makefile.in (tmp-igen, tmp-m16): Drop -F and -M options to
 	igen. Replace with configuration variables sim_igen_flags /
 	sim_m16_flags.

	end-sanitize-v5900
	* r5900.igen: New file. Copy v5900 insns here.
	start-sanitize-r5900
	end-sanitize-v5400
	* vr5400.igen: New file. 
	start-sanitize-vr5400
	* m16.igen: New file.  Copy mips16 insns here.
	* mips.igen: From here.

Mon Oct 27 13:53:59 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	start-sanitize-vr5400
	* mips.igen: Tag all mipsIV instructions with vr5400 model.

	* configure.in: Add mips64vr5400 target.
	* configure: Re-generate.

	end-sanitize-vr5400
	* Makefile.in (SIM_NO_OBJ): Define, move SIM_M16_OBJ, SIM_IGEN_OBJ
 	to top.
	(tmp-igen, tmp-m16): Pass -I srcdir to igen.

Sat Oct 25 16:51:40 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c (build_instruction): Follow sim_write's lead in using
	BigEndianMem instead of !ByteSwapMem.

Fri Oct 24 17:41:49 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure.in (sim_gen): Dependent on target, select type of
 	generator.  Always select old style generator.

	configure: Re-generate.

	Makefile.in (tmp-igen, tmp-m16, clean-m16, clean-igen): New
 	targets.
	(SIM_M16_CFLAGS, SIM_M16_ALL, SIM_M16_OBJ, BUILT_SRC_FROM_M16,
 	SIM_IGEN_CFLAGS, SIM_IGEN_ALL, SIM_IGEN_OBJ, BUILT_SRC_FROM_IGEN,
 	IGEN_TRACE, IGEN_INSN, IGEN_DC): Define
	(SIM_EXTRA_CFLAGS, SIM_EXTRA_ALL, SIM_OBJS): Add member
 	SIM_@sim_gen@_*, set by autoconf.
	
Wed Oct 22 12:52:06 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* sim-main.h (NULLIFY_NEXT_INSTRUCTION, DELAY_SLOT): Define.

	* interp.c (ColdReset): Remove #ifdef HASFPU, check
 	CURRENT_FLOATING_POINT instead.

	* interp.c (ifetch32): New function. Fetch 32 bit instruction.
	(address_translation): Raise exception InstructionFetch when
 	translation fails and isINSTRUCTION.
	
	* interp.c (sim_open, sim_write, sim_monitor, store_word,
 	sim_engine_run): Change type of of vaddr and paddr to
 	address_word.
	(address_translation, prefetch, load_memory, store_memory,
 	cache_op): Change type of vAddr and pAddr to address_word.

	* gencode.c (build_instruction): Change type of vaddr and paddr to
 	address_word.

Mon Oct 20 15:29:04 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* sim-main.h (ALU64_END, ALU32_END): Use ALU*_OVERFLOW_RESULT
 	macro to obtain result of ALU op.

Tue Oct 21 17:39:14 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_info): Call profile_print.

Mon Oct 20 13:31:20 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (SIM_OBJS): Add sim-profile.o module.

	* sim-main.h (WITH_PROFILE): Do not define, defined in
 	common/sim-config.h.  Use sim-profile module.
	(simPROFILE): Delete defintion.

	* interp.c (PROFILE): Delete definition.
	(mips_option_handler): Delete 'p', 'y' and 'x' profile options.
	(sim_close): Delete code writing profile histogram.
	(mips_set_profile, mips_set_profile_size, writeout16, writeout32):
 	Delete.
	(sim_engine_run): Delete code profiling the PC.

Mon Oct 20 13:31:20 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* sim-main.h (SIGNEXTEND): Force type of result to unsigned_word.

	* interp.c (sim_monitor): Make register pointers of type
 	unsigned_word*.

	* sim-main.h: Make registers of type unsigned_word not
 	signed_word.

Thu Oct 16 10:31:39 1997  Andrew Cagney  <cagney@b1.cygnus.com>

start-sanitize-r5900
	* sim-main.h (BYTES_IN_MMI_REGS, ..., SUB_REG_FETCH, ..., GPR_SB,
 	...): Move to sim-main.h
	
end-sanitize-r5900
	* interp.c (sync_operation): Rename from SyncOperation, make
 	global, add SD argument.
	(prefetch): Rename from Prefetch, make global, add SD argument.
	(decode_coproc): Make global.

	* sim-main.h (SyncOperation, DecodeCoproc, Pefetch): Define.

	* gencode.c (build_instruction): Generate DecodeCoproc not
 	decode_coproc calls.

	* interp.c (SETFCC, GETFCC, PREVCOC1): Move to sim-main.h
	(SizeFGR): Move to sim-main.h
	(simHALTEX, simHALTIN, simTRACE, simPROFILE, simDELAYSLOT,
 	simSIGINT, simJALDELAYSLOT): Move to sim-main.h
	(FP_FLAGS, FP_ENABLE, FP_CAUSE, IR, UF, OF, DZ, IO, UO): Move to
 	sim-main.h.
	(FP_FS, FP_MASK_RM, FP_SH_RM, FP_RM_NEAREST, FP_RM_TOPINF,
 	FP_RM_TOMINF, GETRM): Move to sim-main.h.
	(Uncached, CachedNoncoherent, CachedCoherent, Cached,
 	isINSTRUCTION, ..., AccessLength_BYTE, ...): Move to sim-main.h.
	(UserMode, BigEndianMem, ByteSwapMem, ReverseEndian,
 	BigEndianCPU, status_KSU_mask, ...). Moved to sim-main.h
	
	* sim-main.h (ALU32_END, ALU64_END): Define. When overflow raise
 	exception.
	(sim-alu.h): Include.
	(NULLIFY_NIA, NULL_CIA, CPU_CIA): Define.
 	(sim_cia): Typedef to instruction_address.
	
Thu Oct 16 10:31:41 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (interp.o): Rename generated file engine.c to
	oengine.c.
  	
	* interp.c: Update.
	
Thu Oct 16 10:31:40 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_instruction): Use FPR_STATE not fpr_state.
	
Thu Oct 16 10:31:39 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_instruction): For "FPSQRT", output correct
 	number of arguments to Recip.
	
Tue Oct 14 17:38:18 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (interp.o): Depends on sim-main.h

	* interp.c (mips16_entry, ColdReset,dotrace): Add SD argument. Use GPR not registers.

	* sim-main.h (sim_cpu): Add registers, register_widths, fpr_state,
 	ipc, dspc, pending_*, hiaccess, loaccess, state, dsstate fields.
 	(REGISTERS, REGISTER_WIDTHS, FPR_STATE, IPC, DSPC, PENDING_*,
 	STATE, DSSTATE): Define
	(GPR, FGRIDX, ..): Define.

	* interp.c (registers, register_widths, fpr_state, ipc, dspc,
 	pending_*, hiaccess, loaccess, state, dsstate): Delete globals.
	(GPR, FGRIDX, ...): Delete macros.
	
	* interp.c: Update names to match defines from sim-main.h
	
Tue Oct 14 15:11:45 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_monitor): Add SD argument.
	(sim_warning): Delete.  Replace calls with calls to
 	sim_io_eprintf.
	(sim_error): Delete. Replace calls with sim_io_error.
	(open_trace, writeout32, writeout16, getnum): Add SD argument.
	(mips_set_profile): Rename from sim_set_profile. Add SD argument.
	(mips_set_profile_size): Rename from sim_set_profile_size. Add SD
 	argument.
	(mips_size): Rename from sim_size. Add SD argument.

	* interp.c (simulator): Delete global variable.
	(callback): Delete global variable.
	(mips_option_handler, sim_open, sim_write, sim_read,
 	sim_store_register, sim_fetch_register, sim_info, sim_do_command,
 	sim_size,sim_monitor): Use sim_io_* not callback->*.
	(sim_open): ZALLOC simulator struct.
	(PROFILE): Do not define.

Tue Oct 14 13:35:48 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_open), support.h: Replace CHECKSIM macro found in
 	support.h with corresponding code.

	* sim-main.h (word64, uword64), support.h: Move definition to
 	sim-main.h.
	(WORD64LO, WORD64HI, SET64LO, SET64HI, WORD64, UWORD64): Ditto.

	* support.h: Delete
	* Makefile.in: Update dependencies
	* interp.c: Do not include.
	
Tue Oct 14 13:35:48 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (address_translation, load_memory, store_memory,
 	cache_op): Rename to from AddressTranslation et.al., make global,
 	add SD argument
	
	* sim-main.h (AddressTranslation, LoadMemory, StoreMemory,
 	CacheOp): Define.
	
	* interp.c (SignalException): Rename to signal_exception, make
 	global.

	* interp.c (Interrupt, ...): Move definitions to sim-main.h.
	
	* sim-main.h (SignalException, SignalExceptionInterrupt,
 	SignalExceptionInstructionFetch, SignalExceptionAddressStore,
 	SignalExceptionAddressLoad, SignalExceptionSimulatorFault,
 	SignalExceptionIntegerOverflow, SignalExceptionCoProcessorUnusable):
 	Define.
  	
	* interp.c, support.h: Use.
	
Tue Oct 14 13:19:20 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (ValueFPR, StoreFPR), sim-main.h: Make global, rename
 	to value_fpr / store_fpr. Add SD argument.
	(NaN, Infinity, Less, Equal, AbsoluteValue, Negate, Add, Sub,
 	Multiply, Divide, Recip, SquareRoot, Convert): Make global.

	* sim-main.h (ValueFPR, StoreFPR): Define.
	
Tue Oct 14 13:06:55 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_engine_run): Check consistency between configure
 	WITH_TARGET_WORD_BITSIZE and WITH_FLOATING_POINT and gensim GPRLEN
 	and HASFPU.

	* configure.in (mips_bitsize): Configure WITH_TARGET_WORD_BITSIZE.
        (mips_fpu): Configure WITH_FLOATING_POINT.
	(mips_endian): Configure WITH_TARGET_ENDIAN.
	* configure: Update.

Fri Oct  3 09:28:00 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

start-sanitize-r5900
Mon Aug 25 19:11:15 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (MAX_REG): Allow up-to 128 registers.
	(LO1, HI1): Define value that matches REGISTER_NAMES in gdb.
	(REGISTER_SA): Ditto.
	(sim_open): Initialize register_widths for r5900 specific
 	registers.
	(sim_fetch_register, sim_store_register): Check for request of
 	r5900 specific SA register.  Check for request for hi 64 bits of
 	r5900 specific registers.
	
end-sanitize-r5900
Mon Sep 29 14:45:00 1997  Bob Manson  <manson@charmed.cygnus.com>

	* configure: Regenerated.

Fri Sep 26 12:48:18 1997  Mark Alexander  <marka@cygnus.com>

	* interp.c: Allow Debug, DEPC, and EPC registers to be examined in GDB.

Thu Sep 25 11:15:22 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (print_igen_insn_models): Assume certain architectures
 	include all mips* instructions.
	(print_igen_insn_format): Use data_size==-1 as marker for MIPS16
 	instruction.

	* Makefile.in (tmp.igen): Add target. Generate igen input from
 	gencode file.

	* gencode.c (FEATURE_IGEN): Define.
	(main): Add --igen option.  Generate output in igen format.
	(process_instructions): Format output according to igen option.
	(print_igen_insn_format): New function.
	(print_igen_insn_models): New function.
	(process_instructions): Only issue warnings and ignore
 	instructions when no FEATURE_IGEN.

Wed Sep 24 17:38:57 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (COP_SD, COP_LD): Add UNUSED to pacify GCC for some
 	MIPS targets.

Tue Sep 23 11:04:38 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Tue Sep 23 10:19:51 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (SIM_ALIGNMENT, SIM_ENDIAN, SIM_HOSTENDIAN,
 	SIM_RESERVED_BITS): Delete, moved to common.
	(SIM_EXTRA_CFLAGS): Update.
	
Mon Sep 22 11:46:20 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure.in: Configure non-strict memory alignment.
	* configure: Regenerated to track ../common/aclocal.m4 changes.

Fri Sep 19 17:45:25 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Sat Sep 20 14:07:28 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c (SDBBP,DERET): Added (3900) insns.
	(RFE): Turn on for 3900.
	* interp.c (DebugBreakPoint,DEPC,Debug,Debug_*): Added.
	(dsstate): Made global.
	(SUBTARGET_R3900): Added.
	(CANCELDELAYSLOT): New.
	(SignalException): Ignore SystemCall rather than ignore and
	terminate.  Add DebugBreakPoint handling.
	(decode_coproc): New insns RFE, DERET; and new registers Debug
	and DEPC protected by SUBTARGET_R3900.
	(sim_engine_run): Use CANCELDELAYSLOT rather than clearing
	bits explicitly.
	* Makefile.in,configure.in: Add mips subtarget option.
	* configure: Update.	

Fri Sep 19 09:33:27 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c: Add r3900 (tx39).
	
start-sanitize-tx19
	* gencode.c: Fix some configuration problems by improving 
	the relationship between tx19 and tx39.
end-sanitize-tx19

Tue Sep 16 15:52:04 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c (build_instruction): Don't need to subtract 4 for
	JALR, just 2.

Tue Sep 16 11:32:28 1997  Gavin Koch  <gavin@cygnus.com>

	* interp.c: Correct some HASFPU problems.

Mon Sep 15 17:36:15 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Fri Sep 12 12:01:39 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (mips_options): Fix samples option short form, should
 	be `x'.

Thu Sep 11 09:35:29 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_info): Enable info code.  Was just returning.

Tue Sep  9 17:30:57 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (decode_coproc): Clarify warning about unsuported MTC0,
 	MFC0.

Tue Sep  9 16:28:28 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_instruction): Use SIGNED64 for 64 bit
 	constants.
	(build_instruction): Ditto for LL.

start-sanitize-tx19
Sun Sep  7 16:05:46 1997  Gavin Koch  <gavin@cygnus.com>

	* mips/configure.in, mips/gencode: Add tx19/r1900.

end-sanitize-tx19
Thu Sep  4 17:21:23 1997  Doug Evans  <dje@seba>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

start-sanitize-r5900
Mon Sep  1 18:43:30 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_instruction): For "pabsw" and "pabsh", check
 	for overflow due to ABS of MININT, set result to MAXINT.
	(build_instruction): For "psrlvw", signextend bit 31.

end-sanitize-r5900
Wed Aug 27 18:13:22 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.
	* config.in: Ditto.

Wed Aug 27 14:12:27 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_open): Add call to sim_analyze_program, update
 	call to sim_config.

Tue Aug 26 10:40:07 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_kill): Delete.
	(sim_create_inferior): Add ABFD argument. Set PC from same.
	(sim_load): Move code initializing trap handlers from here.
	(sim_open): To here.
	(sim_load): Delete, use sim-hload.c.

	* Makefile.in (SIM_OBJS): Add sim-hload.o module.

Mon Aug 25 17:50:22 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.
	* config.in: Ditto.

Mon Aug 25 15:59:48 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_open): Add ABFD argument.
	(sim_load): Move call to sim_config from here.
	(sim_open): To here.  Check return status.

start-sanitize-r5900
	* gencode.c (build_instruction): Do not define x8000000000000000,
 	x7FFFFFFFFFFFFFFF, or xFFFFFFFF80000000.

end-sanitize-r5900
start-sanitize-r5900
Mon Jul 28 19:49:29 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_instruction): For "pdivw", "pdivbw" and
 	"pdivuw" check for overflow due to signed divide by -1.

end-sanitize-r5900
Fri Jul 25 15:00:45 1997  Gavin Koch  <gavin@cygnus.com>
 
 	* gencode.c (build_instruction): Two arg MADD should
 	not assign result to $0.
 
start-sanitize-r5900
Thu Jul 10 11:58:48 1997  Andrew Cagney  <cagney@critters.cygnus.com>

	* gencode.c (build_instruction): For "ppac5" use unsigned
 	arrithmetic so that the sign bit doesn't smear when right shifted.
	(build_instruction): For "pdiv" perform sign extension when
 	storing results in HI and LO.
	(build_instructions): For "pdiv" and "pdivbw" check for
 	divide-by-zero.
	(build_instruction): For "pmfhl.slw" update hi part of dest
 	register as well as low part.
	(build_instruction): For "pmfhl" portably handle long long values.
	(build_instruction): For "pmfhl.sh" correctly negative values.
  	Store half words 2 and three in the correct place.
	(build_instruction): For "psllvw", sign extend value after shift.

end-sanitize-r5900
Thu Jun 26 12:13:17 1997  Angela Marie Thomas (angela@cygnus.com)

	* sim/mips/configure: Change default_sim_endian to 0 (bi-endian)
	* sim/mips/configure.in: Regenerate.

Wed Jul  9 10:29:21 1997  Andrew Cagney  <cagney@critters.cygnus.com>

	* interp.c (SUB_REG_UW, SUB_REG_SW, SUB_REG_*): Use more explicit
 	signed8, unsigned8 et.al. types.

start-sanitize-r5900
	* gencode.c (build_instruction): For PMULTU* do not sign extend
 	registers.  Make generated code easier to debug.

end-sanitize-r5900
	* interp.c (SUB_REG_FETCH): Handle both little and big endian
 	hosts when selecting subreg.

start-sanitize-r5900
Tue Jul  8 18:07:20 1997  Andrew Cagney  <cagney@andros.cygnus.com>

	* gencode.c (type_for_data_len): For 32bit operations concerned
 	with overflow, perform op using 64bits.
	(build_instruction): For PADD, always compute operation using type
 	returned by type_for_data_len.
	(build_instruction): For PSUBU, when overflow, saturate to zero as
 	actually underflow.

end-sanitize-r5900
Wed Jul  2 11:54:10 1997  Jeffrey A Law  (law@cygnus.com)

start-sanitize-r5900
	* gencode.c (build_instruction): Handle "pext5" according to
	version 1.95 of the r5900 ISA.

	* gencode.c (build_instruction): Handle "ppac5" according to
	version 1.95 of the r5900 ISA.

end-sanitize-r5900
	* interp.c (sim_engine_run): Reset the ZERO register to zero
	regardless of FEATURE_WARN_ZERO.
	* gencode.c (FEATURE_WARNINGS): Remove FEATURE_WARN_ZERO.

Wed Jun  4 10:43:14 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (decode_coproc): Implement MTC0 N, CAUSE.
	(SignalException): For BreakPoints ignore any mode bits and just
 	save the PC.
	(SignalException): Always set the CAUSE register.

Tue Jun  3 05:00:33 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (SignalException): Clear the simDELAYSLOT flag when an
 	exception has been taken.

	* interp.c: Implement the ERET and mt/f sr instructions.

start-sanitize-r5900
Mon Jun  2 23:28:19 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* gencode.c (build_instruction): For paddu, extract unsigned
 	sub-fields.

	* gencode.c (build_instruction): Saturate padds instead of padd
 	instructions.

end-sanitize-r5900
Sat May 31 00:44:16 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (SignalException): Don't bother restarting an
 	interrupt.

Fri May 30 23:41:48 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (SignalException): Really take an interrupt.
	(interrupt_event): Only deliver interrupts when enabled.

Tue May 27 20:08:06 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_info): Only print info when verbose.
	(sim_info) Use sim_io_printf for output.
	
Tue May 27 14:22:23 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (CoProcPresent): Add UNUSED attribute - not used by all
 	mips architectures.

Tue May 27 14:22:23 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_do_command): Check for common commands if a
 	simulator specific command fails.

Thu May 22 09:32:03 1997  Gavin Koch  <gavin@cygnus.com>

	* interp.c (sim_engine_run): ifdef out uses of simSTOP, simSTEP
	and simBE when DEBUG is defined.

Wed May 21 09:08:10 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (interrupt_event): New function.  Pass exception event
 	onto exception handler.

	* configure.in: Check for stdlib.h.
	* configure: Regenerate.

	* gencode.c (build_instruction): Add UNUSED attribute to tempS
 	variable declaration.
	(build_instruction): Initialize memval1.
	(build_instruction): Add UNUSED attribute to byte, bigend,
 	reverse.
	(build_operands): Ditto.

	* interp.c: Fix GCC warnings.
	(sim_get_quit_code): Delete.

	* configure.in: Add INLINE, ENDIAN, HOSTENDIAN and WARNINGS.
	* Makefile.in: Ditto.
	* configure: Re-generate.
	
	* Makefile.in (SIM_OBJS): Add sim-watch.o module.

Tue May 20 15:08:56 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (mips_option_handler): New function parse argumes using
 	sim-options.
	(myname): Replace with STATE_MY_NAME.
	(sim_open): Delete check for host endianness - performed by
 	sim_config.
	(simHOSTBE, simBE): Delete, replaced by sim-endian flags.
	(sim_open): Move much of the initialization from here.
	(sim_load): To here.  After the image has been loaded and
 	endianness set.
	(sim_open): Move ColdReset from here.
	(sim_create_inferior): To here.
	(sim_open): Make FP check less dependant on host endianness.

	* Makefile.in (SIM_RUN_OBJS): Set to nrun.o - use new version or
 	run.
	* interp.c (sim_set_callbacks): Delete.

	* interp.c (membank, membank_base, membank_size): Replace with
 	STATE_MEMORY, STATE_MEM_SIZE, STATE_MEM_BASE.
	(sim_open): Remove call to callback->init. gdb/run do this.

	* interp.c: Update

	* sim-main.h (SIM_HAVE_FLATMEM): Define.

	* interp.c (big_endian_p): Delete, replaced by
 	current_target_byte_order.

Tue May 20 13:55:00 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (host_read_long, host_read_word, host_swap_word,
 	host_swap_long): Delete. Using common sim-endian.
	(sim_fetch_register, sim_store_register): Use H2T.
	(pipeline_ticks): Delete.  Handled by sim-events.
	(sim_info): Update.
	(sim_engine_run): Update.

Tue May 20 13:42:03 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_stop_reason): Move code determining simEXCEPTION
 	reason from here.
	(SignalException): To here. Signal using sim_engine_halt.
	(sim_stop_reason): Delete, moved to common.
	
Tue May 20 10:19:48 1997  Andrew Cagney  <cagney@b2.cygnus.com>

	* interp.c (sim_open): Add callback argument.
	(sim_set_callbacks): Delete SIM_DESC argument.
	(sim_size): Ditto.

Mon May 19 18:20:38 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* Makefile.in (SIM_OBJS): Add common modules.

	* interp.c (sim_set_callbacks): Also set SD callback.
	(set_endianness, xfer_*, swap_*): Delete.
	(host_read_word, host_read_long, host_swap_word, host_swap_long):
 	Change to functions using sim-endian macros.
	(control_c, sim_stop): Delete, use common version.
	(simulate): Convert into.
	(sim_engine_run): This function.
	(sim_resume): Delete.
	
	* interp.c (simulation): New variable - the simulator object.
	(sim_kind): Delete global - merged into simulation.
	(sim_load): Cleanup.  Move PC assignment from here.
	(sim_create_inferior): To here.

	* sim-main.h: New file.
	* interp.c (sim-main.h): Include.
	
Thu Apr 24 00:39:51 1997  Doug Evans  <dje@canuck.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Wed Apr 23 17:32:19 1997  Doug Evans  <dje@canuck.cygnus.com>

	* tconfig.in (SIM_HAVE_BIENDIAN): Define.

Mon Apr 21 17:16:13 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c (build_instruction): DIV instructions: check 
	for division by zero and integer overflow before using 
	host's division operation.

Thu Apr 17 03:18:14 1997  Doug Evans  <dje@canuck.cygnus.com>

	* Makefile.in (SIM_OBJS): Add sim-load.o.
	* interp.c: #include bfd.h.
	(target_byte_order): Delete.
	(sim_kind, myname, big_endian_p): New static locals.
	(sim_open): Set sim_kind, myname.  Move call to set_endianness to
	after argument parsing.  Recognize -E arg, set endianness accordingly.
	(sim_load): Return SIM_RC.  New arg abfd.  Call sim_load_file to
	load file into simulator.  Set PC from bfd.
	(sim_create_inferior): Return SIM_RC.  Delete arg start_address.
	(set_endianness): Use big_endian_p instead of target_byte_order.

Wed Apr 16 17:55:37 1997  Andrew Cagney  <cagney@b1.cygnus.com>

	* interp.c (sim_size): Delete prototype - conflicts with
 	definition in remote-sim.h.  Correct definition.

Mon Apr  7 15:45:02 1997  Andrew Cagney  <cagney@kremvax.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.
	* config.in: Ditto.

Wed Apr  2 15:06:28 1997  Doug Evans  <dje@canuck.cygnus.com>

	* interp.c (sim_open): New arg `kind'.

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Wed Apr  2 14:34:19 1997 Andrew Cagney <cagney@kremvax.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Tue Mar 25 11:38:22 1997  Doug Evans  <dje@canuck.cygnus.com>

	* interp.c (sim_open): Set optind to 0 before calling getopt.

Wed Mar 19 01:14:00 1997  Andrew Cagney  <cagney@kremvax.cygnus.com>

	* configure: Regenerated to track ../common/aclocal.m4 changes.

Mon Mar 17 10:52:59 1997  Gavin Koch  <gavin@cetus.cygnus.com>

	* interp.c : Replace uses of pr_addr with pr_uword64
	where the bit length is always 64 independent of SIM_ADDR.
	(pr_uword64) : added.

Mon Mar 17 15:10:07 1997  Andrew Cagney  <cagney@kremvax.cygnus.com>

	* configure: Re-generate.

Fri Mar 14 10:34:11 1997  Michael Meissner  <meissner@cygnus.com>

	* configure: Regenerate to track ../common/aclocal.m4 changes.

Thu Mar 13 12:51:36 1997  Doug Evans  <dje@canuck.cygnus.com>

	* interp.c (sim_open): New SIM_DESC result.  Argument is now
	in argv form.
	(other sim_*): New SIM_DESC argument.

start-sanitize-r5900
Wed Feb 26 18:32:21 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c (POP_AND,POP_OR,POP_NOR,POP_XOR): 
	Change values to avoid overloading DOUBLEWORD which is tested
	for all insns.
	* gencode.c: reinstate "offending code".

end-sanitize-r5900
Mon Feb 24 22:47:14 1997  Dawn Perchik  <dawn@cygnus.com>

	* interp.c: Fix printing of addresses for non-64-bit targets.
	(pr_addr): Add function to print address based on size.
start-sanitize-r5900
	* gencode.c: #ifdef out offending code until a permanent fix 
	can be added.  Code is causing build errors for non-5900 mips targets.
end-sanitize-r5900

start-sanitize-r5900
Thu Feb 20 10:40:24 1997  Gavin Koch  <gavin@cetus.cygnus.com>

	* gencode.c (process_instructions): Correct test for ISA dependent
	architecture bits in isa field of MIPS_DECODE.

end-sanitize-r5900
Wed Feb 19 14:42:09 1997  Mark Alexander  <marka@cygnus.com>

	* interp.c (simopen): Add support for LSI MiniRISC PMON vectors.

start-sanitize-r5900
Tue Feb 18 17:03:47 1997  Gavin Koch  <gavin@cygnus.com>

	* gencode.c (MIPS_DECODE): Correct instruction feature flags for 
	PMADDUW.

end-sanitize-r5900
Thu Feb 13 14:08:30 1997  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (build_mips16_operands): Correct computation of base
	address for extended PC relative instruction.

start-sanitize-r5900
Fri Feb  7 11:12:44 1997  Gavin Koch  <gavin@cygnus.com>

	* Makefile.in, configure, configure.in, gencode.c, 
	interp.c, support.h: add r5900.

end-sanitize-r5900
Thu Feb  6 17:16:15 1997  Ian Lance Taylor  <ian@cygnus.com>

	* interp.c (mips16_entry): Add support for floating point cases.
	(SignalException): Pass floating point cases to mips16_entry.
	(ValueFPR): Don't restrict fmt_single and fmt_word to even
	registers.
	(StoreFPR): Likewise.  Also, don't clobber fpr + 1 for fmt_single
	or fmt_word.
	(COP_LW): Pass fmt_word rather than fmt_uninterpreted to StoreFPR,
	and then set the state to fmt_uninterpreted.
	(COP_SW): Temporarily set the state to fmt_word while calling
	ValueFPR.

Tue Feb  4 16:48:25 1997  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (build_instruction): The high order may be set in the
	comparison flags at any ISA level, not just ISA 4.

Tue Feb  4 13:33:30 1997  Doug Evans  <dje@canuck.cygnus.com>

	* Makefile.in (@COMMON_MAKEFILE_FRAG): Use
	COMMON_{PRE,POST}_CONFIG_FRAG instead.
	* configure.in: sinclude ../common/aclocal.m4.
	* configure: Regenerated.

Fri Jan 31 11:11:45 1997  Ian Lance Taylor  <ian@cygnus.com>

	* configure: Rebuild after change to aclocal.m4.

Thu Jan 23 11:46:23 1997  Stu Grossman  (grossman@critters.cygnus.com)

	* configure configure.in Makefile.in:  Update to new configure
	scheme which is more compatible with WinGDB builds.
	* configure.in:  Improve comment on how to run autoconf.
	* configure:  Re-run autoconf to get new ../common/aclocal.m4.
	* Makefile.in:  Use autoconf substitution to install common
	makefile fragment.

Wed Jan  8 12:39:03 1997  Jim Wilson  <wilson@cygnus.com>

	* gencode.c (build_instruction): Use BigEndianCPU instead of
	ByteSwapMem.

Thu Jan 02 22:23:04 1997  Mark Alexander  <marka@cygnus.com>

	* interp.c (sim_monitor): Make output to stdout visible in
	wingdb's I/O log window.

Tue Dec 31 07:04:00 1996  Mark Alexander  <marka@cygnus.com>

	* support.h: Undo previous change to SIGTRAP
	and SIGQUIT values.

Mon Dec 30 17:36:06 1996  Ian Lance Taylor  <ian@cygnus.com>

	* interp.c (store_word, load_word): New static functions.
	(mips16_entry): New static function.
	(SignalException): Look for mips16 entry and exit instructions.
	(simulate): Use the correct index when setting fpr_state after
	doing a pending move.

Sun Dec 29 09:37:18 1996  Mark Alexander  <marka@cygnus.com>

	* interp.c: Fix byte-swapping code throughout to work on
	both little- and big-endian hosts.

Sun Dec 29 09:18:32 1996  Mark Alexander  <marka@cygnus.com>

	* support.h: Make definitions of SIGTRAP and SIGQUIT consistent
	with gdb/config/i386/xm-windows.h.

Fri Dec 27 22:48:51 1996  Mark Alexander  <marka@cygnus.com>

	* gencode.c (build_instruction): Work around MSVC++ code gen bug
	that messes up arithmetic shifts.

Fri Dec 20 11:04:05 1996  Stu Grossman  (grossman@critters.cygnus.com)

	* support.h:  Use _WIN32 instead of __WIN32__.  Also add defs for
	SIGTRAP and SIGQUIT for _WIN32.

Thu Dec 19 14:07:27 1996  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (build_instruction) [MUL]: Cast operands to word64, to
	force a 64 bit multiplication.
	(build_instruction) [OR]: In mips16 mode, don't do anything if the
	destination register is 0, since that is the default mips16 nop
	instruction.

Mon Dec 16 14:59:38 1996  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (MIPS16_DECODE): SWRASP is I8, not RI.
	(build_endian_shift): Don't check proc64.
	(build_instruction): Always set memval to uword64.  Cast op2 to
	uword64 when shifting it left in memory instructions.  Always use
	the same code for stores--don't special case proc64.

	* gencode.c (build_mips16_operands): Fix base PC value for PC
	relative operands.
	(build_instruction): Call JALDELAYSLOT rather than DELAYSLOT for a
	jal instruction.
	* interp.c (simJALDELAYSLOT): Define.
 	(JALDELAYSLOT): Define.
	(INDELAYSLOT, INJALDELAYSLOT): Define.
	(simulate): Clear simJALDELAYSLOT when simDELAYSLOT is cleared.

Tue Dec 24 22:11:20 1996  Angela Marie Thomas (angela@cygnus.com)

	* interp.c (sim_open): add flush_cache as a PMON routine
	(sim_monitor): handle flush_cache by ignoring it

Wed Dec 11 13:53:51 1996  Jim Wilson  <wilson@cygnus.com>

	* gencode.c (build_instruction): Use !ByteSwapMem instead of
	BigEndianMem.
	* interp.c (CONFIG, config_EP_{mask,shift,D,DxxDxx, config_BE): Delete.
	(BigEndianMem): Rename to ByteSwapMem and change sense.
	(BigEndianCPU, sim_write, LoadMemory, StoreMemory): Change
	BigEndianMem references to !ByteSwapMem.
	(set_endianness): New function, with prototype.
	(sim_open): Call set_endianness.
	(sim_info): Use simBE instead of BigEndianMem.
	(xfer_direct_word, xfer_direct_long, swap_direct_word,
	swap_direct_long, xfer_big_word, xfer_big_long, xfer_little_word,
	xfer_little_long, swap_word, swap_long): Delete unnecessary MSC_VER
	ifdefs, keeping the prototype declaration.
	(swap_word): Rewrite correctly.
	(ColdReset): Delete references to CONFIG.  Delete endianness related
	code; moved to set_endianness.
	
Tue Dec 10 11:32:04 1996  Jim Wilson  <wilson@cygnus.com>

	* gencode.c (build_instruction, case JUMP): Truncate PC to 32 bits.
	* interp.c (CHECKHILO): Define away.
	(simSIGINT): New macro.
	(membank_size): Increase from 1MB to 2MB.
	(control_c): New function.
	(sim_resume): Rename parameter signal to signal_number.  Add local
	variable prev.  Call signal before and after simulate.
	(sim_stop_reason): Add simSIGINT support.
	(sim_warning, sim_error, dotrace, SignalException): Define as stdarg
	functions always.
	(sim_warning): Delete call to SignalException.  Do call printf_filtered
	if logfh is NULL.
	(AddressTranslation): Add #ifdef DEBUG around debugging message and
	a call to sim_warning.

Wed Nov 27 11:53:50 1996  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (process_instructions): If ! proc64, skip DOUBLEWORD
	16 bit instructions.

Tue Nov 26 11:53:12 1996  Ian Lance Taylor  <ian@cygnus.com>

	Add support for mips16 (16 bit MIPS implementation):
	* gencode.c (inst_type): Add mips16 instruction encoding types.
	(GETDATASIZEINSN): Define.
	(MIPS_DECODE): Add REG flag to dsllv, dsrav, and dsrlv.  Add
	jalx.  Add LEFT flag to mfhi and mflo.  Add RIGHT flag to mthi and
	mtlo.
	(MIPS16_DECODE): New table, for mips16 instructions.
	(bitmap_val): New static function.
	(struct mips16_op): Define.
	(mips16_op_table): New table, for mips16 operands.
	(build_mips16_operands): New static function.
	(process_instructions): If PC is odd, decode a mips16
	instruction.  Break out instruction handling into new
	build_instruction function.
	(build_instruction): New static function, broken out of
	process_instructions.  Check modifiers rather than flags for SHIFT
	bit count and m[ft]{hi,lo} direction.
	(usage): Pass program name to fprintf.
	(main): Remove unused variable this_option_optind.  Change
	``*loptarg++'' to ``loptarg++''.
	(my_strtoul): Parenthesize && within ||.
	* interp.c (LoadMemory): Accept a halfword pAddr if vAddr is odd.
	(simulate): If PC is odd, fetch a 16 bit instruction, and
	increment PC by 2 rather than 4.
	* configure.in: Add case for mips16*-*-*.
	* configure: Rebuild.

Fri Nov 22 08:49:36 1996  Mark Alexander  <marka@cygnus.com>

	* interp.c: Allow -t to enable tracing in standalone simulator.
	Fix garbage output in trace file and error messages.

Wed Nov 20 01:54:37 1996  Doug Evans  <dje@canuck.cygnus.com>

	* Makefile.in: Delete stuff moved to ../common/Make-common.in.
	(SIM_{OBJS,EXTRA_CFLAGS,EXTRA_CLEAN}): Define.
	* configure.in: Simplify using macros in ../common/aclocal.m4.
	* configure: Regenerated.
	* tconfig.in: New file.

Tue Nov 12 13:34:00 1996  Dawn Perchik  <dawn@cygnus.com>

	* interp.c: Fix bugs in 64-bit port.
	Use ansi function declarations for msvc compiler.
	Initialize and test file pointer in trace code.
	Prevent duplicate definition of LAST_EMED_REGNUM.

Tue Oct 15 11:07:06 1996  Mark Alexander  <marka@cygnus.com>

	* interp.c (xfer_big_long): Prevent unwanted sign extension.

Thu Sep 26 17:35:00 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (SignalException): Check for explicit terminating
 	breakpoint value.
	* gencode.c: Pass instruction value through SignalException()
 	calls for Trap, Breakpoint and Syscall.

Thu Sep 26 11:35:17 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (SquareRoot): Add HAVE_SQRT check to ensure sqrt() is
 	only used on those hosts that provide it.
	* configure.in: Add sqrt() to list of functions to be checked for.
	* config.in: Re-generated.
	* configure: Re-generated.

Fri Sep 20 15:47:12 1996  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (process_instructions): Call build_endian_shift when
	expanding STORE RIGHT, to fix swr.
	* support.h (SIGNEXTEND): If the sign bit is not set, explicitly
	clear the high bits.
	* interp.c (Convert): Fix fmt_single to fmt_long to not truncate.
	Fix float to int conversions to produce signed values.

Thu Sep 19 15:34:17 1996  Ian Lance Taylor  <ian@cygnus.com>

	* gencode.c (MIPS_DECODE): Set UNSIGNED for multu instruction.
	(process_instructions): Correct handling of nor instruction.
	Correct shift count for 32 bit shift instructions. Correct sign
	extension for arithmetic shifts to not shift the number of bits in
	the type.  Fix 64 bit multiply high word calculation.  Fix 32 bit
	unsigned multiply.  Fix ldxc1 and friends to use coprocessor 1.
	Fix madd.
	* interp.c (CHECKHILO): Don't set HIACCESS, LOACCESS, or HLPC.
	It's OK to have a mult follow a mult.  What's not OK is to have a
	mult follow an mfhi.
	(Convert): Comment out incorrect rounding code.

Mon Sep 16 11:38:16 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (sim_monitor): Improved monitor printf
 	simulation. Tidied up simulator warnings, and added "--log" option
 	for directing warning message output.
	* gencode.c: Use sim_warning() rather than WARNING macro.

Thu Aug 22 15:03:12 1996  Ian Lance Taylor  <ian@cygnus.com>

	* Makefile.in (gencode): Depend upon gencode.o, getopt.o, and
	getopt1.o, rather than on gencode.c.  Link objects together.
	Don't link against -liberty.
	(gencode.o, getopt.o, getopt1.o): New targets.
	* gencode.c: Include <ctype.h> and "ansidecl.h".
	(AND): Undefine after including "ansidecl.h".
	(ULONG_MAX): Define if not defined.
	(OP_*): Don't define macros; now defined in opcode/mips.h.
	(main): Call my_strtoul rather than strtoul.
	(my_strtoul): New static function.

Wed Jul 17 18:12:38 1996  Stu Grossman  (grossman@critters.cygnus.com)

	* gencode.c (process_instructions):  Generate word64 and uword64
	instead of `long long' and `unsigned long long' data types.
	* interp.c:  #include sysdep.h to get signals, and define default
	for SIGBUS.
	* (Convert):  Work around for Visual-C++ compiler bug with type
	conversion.
	* support.h:  Make things compile under Visual-C++ by using
	__int64 instead of `long long'.  Change many refs to long long
	into word64/uword64 typedefs.

Wed Jun 26 12:24:55 1996  Jason Molenda  (crash@godzilla.cygnus.co.jp)

        * Makefile.in (bindir, libdir, datadir, mandir, infodir, includedir,
        INSTALL_PROGRAM, INSTALL_DATA): Use autoconf-set values.
        (docdir): Removed.
        * configure.in (AC_PREREQ): autoconf 2.5 or higher.
        (AC_PROG_INSTALL): Added.
	(AC_PROG_CC): Moved to before configure.host call.
        * configure: Rebuilt.
	
Wed Jun  5 08:28:13 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* configure.in: Define @SIMCONF@ depending on mips target.
	* configure: Rebuild.
	* Makefile.in (run): Add @SIMCONF@ to control simulator
 	construction.
	* gencode.c: Change LOADDRMASK to 64bit memory model only.
	* interp.c: Remove some debugging, provide more detailed error
 	messages, update memory accesses to use LOADDRMASK.
	
Mon Jun  3 11:55:03 1996  Ian Lance Taylor  <ian@cygnus.com>

	* configure.in: Add calls to AC_CONFIG_HEADER, AC_CHECK_HEADERS,
	AC_CHECK_LIB, and AC_CHECK_FUNCS.  Change AC_OUTPUT to set
	stamp-h.
	* configure: Rebuild.
	* config.in: New file, generated by autoheader.
	* interp.c: Include "config.h".  Include <stdlib.h>, <string.h>,
	and <strings.h> if they exist.  Replace #ifdef sun with #ifdef
	HAVE_ANINT and HAVE_AINT, as appropriate.
	* Makefile.in (run): Use @LIBS@ rather than -lm.
	(interp.o): Depend upon config.h.
	(Makefile): Just rebuild Makefile.
	(clean): Remove stamp-h.
	(mostlyclean): Make the same as clean, not as distclean.
	(config.h, stamp-h): New targets.

Fri May 10 00:41:17 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (ColdReset): Fix boolean test. Make all simulator
 	globals static.

Wed May  8 15:12:58 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (xfer_direct_word, xfer_direct_long,
	swap_direct_word, swap_direct_long, xfer_big_word,
	xfer_big_long, xfer_little_word, xfer_little_long,
	swap_word,swap_long): Added.
	* interp.c (ColdReset): Provide function indirection to
 	host<->simulated_target transfer routines.
	* interp.c (sim_store_register, sim_fetch_register): Updated to
 	make use of indirected transfer routines.

Fri Apr 19 15:48:24 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* gencode.c (process_instructions): Ensure FP ABS instruction
 	recognised.
	* interp.c (AbsoluteValue): Add routine. Also provide simple PMON
 	system call support.

Wed Apr 10 09:51:38 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (sim_do_command): Complain if callback structure not
 	initialised.

Thu Mar 28 13:50:51 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c (Convert): Provide round-to-nearest and round-to-zero
 	support for Sun hosts.
	* Makefile.in (gencode): Ensure the host compiler and libraries
 	used for cross-hosted build.

Wed Mar 27 14:42:12 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* interp.c, gencode.c: Some more (TODO) tidying.

Thu Mar  7 11:19:33 1996  James G. Smith  <jsmith@cygnus.co.uk>

	* gencode.c, interp.c: Replaced explicit long long references with
 	WORD64HI, WORD64LO, SET64HI and SET64LO macro calls.
	* support.h (SET64LO, SET64HI): Macros added.

Wed Feb 21 12:16:21 1996  Ian Lance Taylor  <ian@cygnus.com>

	* configure: Regenerate with autoconf 2.7.

Tue Jan 30 08:48:18 1996  Fred Fish  <fnf@cygnus.com>

	* interp.c (LoadMemory): Enclose text following #endif in /* */.
	* support.h: Remove superfluous "1" from #if.
	* support.h (CHECKSIM): Remove stray 'a' at end of line.

Mon Dec  4 11:44:40 1995  Jamie Smith  <jsmith@cygnus.com>

	* interp.c (StoreFPR): Control UndefinedResult() call on
 	WARN_RESULT manifest.

Fri Dec  1 16:37:19 1995  James G. Smith  <jsmith@cygnus.co.uk>

	* gencode.c: Tidied instruction decoding, and added FP instruction
 	support.

	* interp.c: Added dineroIII, and BSD profiling support. Also
 	run-time FP handling.

Sun Oct 22 00:57:18 1995  James G. Smith  <jsmith@pasanda.cygnus.co.uk>

	* Changelog, Makefile.in, README.Cygnus, configure, configure.in,
 	gencode.c, interp.c, support.h: created.