/* Parameters for execution on a H8/300 series machine. Copyright (C) 1992 Free Software Foundation, Inc. This file is part of GDB. This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* Contributed by Steve Chamberlain sac@cygnus.com */ #define IEEE_FLOAT 1 /* Define the bit, byte, and word ordering of the machine. */ #define TARGET_BYTE_ORDER BIG_ENDIAN #define TARGET_CHAR_BIT 8 #define TARGET_SHORT_BIT 16 #define TARGET_INT_BIT 16 #define TARGET_LONG_BIT 32 #define TARGET_LONG_LONG_BIT 64 #define TARGET_FLOAT_BIT 32 #define TARGET_DOUBLE_BIT 64 /* Offset from address of function to start of its code. Zero on most machines. */ #define FUNCTION_START_OFFSET 0 /* Advance PC across any function entry prologue instructions to reach some "real" code. */ #define SKIP_PROLOGUE(ip) {(ip) = h8300_skip_prologue(ip);} extern CORE_ADDR h8300_skip_prologue (); /* Immediately after a function call, return the saved pc. Can't always go through the frames for this because on some machines the new frame is not set up until the new function executes some instructions. */ #define SAVED_PC_AFTER_CALL(frame) \ read_memory_integer (read_register (SP_REGNUM), 2) /* Stack grows downward. */ #define INNER_THAN < /* Sequence of bytes for breakpoint instruction. This is a TRAP instruction. The last 4 bits (0xf below) is the vector. Systems which don't use 0xf should define BPT_VECTOR themselves before including this file. */ #define BPT_VECTOR 0xf #define BREAKPOINT {0x4e, (0x40 | BPT_VECTOR)} /* If your kernel resets the pc after the trap happens you may need to define this before including this file. */ #define DECR_PC_AFTER_BREAK 2 /* Nonzero if instruction at PC is a return instruction. */ /* Allow any of the return instructions, including a trapv and a return from interupt. */ #define ABOUT_TO_RETURN(pc) ((read_memory_integer (pc, 2) & ~0x3) == 0x4e74) /* Return 1 if P points to an invalid floating point value. */ #define INVALID_FLOAT(p, len) 0 /* Just a first guess; not checked */ /* Say how long registers are. */ #define REGISTER_TYPE short # define NUM_REGS 10 # define REGISTER_BYTES (10*2) /* Index within `registers' of the first byte of the space for register N. */ #define REGISTER_BYTE(N) ((N) * 2) /* Number of bytes of storage in the actual machine representation for register N. On the H8/300, all regs are 2 bytes. */ #define REGISTER_RAW_SIZE(N) 2 /* Number of bytes of storage in the program's representation for register N. On the H8/300, all regs are 2 bytes. */ #define REGISTER_VIRTUAL_SIZE(N) 2 /* Largest value REGISTER_RAW_SIZE can have. */ #define MAX_REGISTER_RAW_SIZE 2 /* Largest value REGISTER_VIRTUAL_SIZE can have. */ #define MAX_REGISTER_VIRTUAL_SIZE 2 /* Nonzero if register N requires conversion from raw format to virtual format. */ #define REGISTER_CONVERTIBLE(N) 0 /* Convert data from raw format for register REGNUM to virtual format for register REGNUM. */ #define REGISTER_CONVERT_TO_VIRTUAL(REGNUM,FROM,TO) bcopy ((FROM), (TO), 2); /* Convert data from virtual format for register REGNUM to raw format for register REGNUM. */ #define REGISTER_CONVERT_TO_RAW(REGNUM,FROM,TO) bcopy ((FROM), (TO), 2); /* Return the GDB type object for the "standard" data type of data in register N. */ #define REGISTER_VIRTUAL_TYPE(N) builtin_type_int /* Initializer for an array of names of registers. Entries beyond the first NUM_REGS are ignored. */ #define REGISTER_NAMES \ {"r0", "r1", "r2", "r3", "r4", "r5", "r6", "sp","ccr","pc"} /* Register numbers of various important registers. Note that some of these values are "real" register numbers, and correspond to the general registers of the machine, and some are "phony" register numbers which are too large to be actual register numbers as far as the user is concerned but do serve to get the desired values when passed to read_register. */ #define FP_REGNUM 6 /* Contains address of executing stack frame */ #define SP_REGNUM 7 /* Contains address of top of stack */ #define CCR_REGNUM 8 /* Contains processor status */ #define PC_REGNUM 9 /* Contains program counter */ /* Store the address of the place in which to copy the structure the subroutine will return. This is called from call_function. */ #define STORE_STRUCT_RETURN(ADDR, SP) \ { write_register (0, (ADDR)); abort(); } /* Extract from an array REGBUF containing the (raw) register state a function return value of type TYPE, and copy that, in virtual format, into VALBUF. This is assuming that floating point values are returned as doubles in d0/d1. */ #define EXTRACT_RETURN_VALUE(TYPE,REGBUF,VALBUF) \ bcopy ((char *)(REGBUF) + \ (TYPE_LENGTH(TYPE) >= 4 ? 0 : 4 - TYPE_LENGTH(TYPE)), \ VALBUF, TYPE_LENGTH(TYPE)) /* Write into appropriate registers a function return value of type TYPE, given in virtual format. Assumes floats are passed in d0/d1. */ #define STORE_RETURN_VALUE(TYPE,VALBUF) \ write_register_bytes (0, VALBUF, TYPE_LENGTH (TYPE)) /* Extract from an array REGBUF containing the (raw) register state the address in which a function should return its structure value, as a CORE_ADDR (or an expression that can be used as one). */ #define EXTRACT_STRUCT_VALUE_ADDRESS(REGBUF) (*(CORE_ADDR *)(REGBUF)) /* Describe the pointer in each stack frame to the previous stack frame (its caller). */ /* FRAME_CHAIN takes a frame's nominal address and produces the frame's chain-pointer. However, if FRAME_CHAIN_VALID returns zero, it means the given frame is the outermost one and has no caller. */ /* In the case of the H8/300, the frame's nominal address is the address of a 2-byte word containing the calling frame's address. */ /* Use the alternate method of avoiding running up off the end of the frame chain or following frames back into the startup code. See the comments in blockframe.c */ #define FRAME_CHAIN_VALID(chain, thisframe) \ (chain != 0 \ && !(inside_main_scope ((thisframe)->pc)) \ && !(inside_entry_scope ((thisframe)->pc))) /* Define other aspects of the stack frame. */ /* A macro that tells us whether the function invocation represented by FI does not have a frame on the stack associated with it. If it does not, FRAMELESS is set to 1, else 0. */ #define FRAMELESS_FUNCTION_INVOCATION(FI, FRAMELESS) \ (FRAMELESS) = frameless_look_for_prologue(FI) #define FRAME_SAVED_PC(FRAME) (read_memory_integer ((FRAME)->frame + 2, 2)) #define FRAME_ARGS_ADDRESS(fi) ((fi)->frame) #define FRAME_LOCALS_ADDRESS(fi) ((fi)->frame) /* Set VAL to the number of args passed to frame described by FI. Can set VAL to -1, meaning no way to tell. */ /* We can't tell how many args there are now that the C compiler delays popping them. */ #define FRAME_NUM_ARGS(val,fi) (val = -1) /* Return number of bytes at start of arglist that are not really args. */ #define FRAME_ARGS_SKIP 4 /* Put here the code to store, into a struct frame_saved_regs, the addresses of the saved registers of frame described by FRAME_INFO. This includes special registers such as pc and fp saved in special ways in the stack frame. sp is even more special: the address we return for it IS the sp for the next frame. */ #define FRAME_FIND_SAVED_REGS(frame_info, frame_saved_regs) abort(); /* Push an empty stack frame, to record the current PC, etc. */ #define PUSH_DUMMY_FRAME { h8300_push_dummy_frame (); } /* Discard from the stack the innermost frame, restoring all registers. */ #define POP_FRAME { h8300_pop_frame (); }