# Copyright 2016-2022 Free Software Foundation, Inc.

# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; either version 3 of the License, or
# (at your option) any later version.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program.  If not, see <http://www.gnu.org/licenses/>.

# Test that on a separate MI UI (new-ui mi <tty>), the printing of an
# asynchronous event (e.g. =library-loaded) during the synchronous
# execution of a command (e.g.  -exec-run or -exec-continue) does not
# prematurely re-enable MI input.  After executing synchronous
# commands, MI should not process further commands until the inferior
# stops again.  See PR gdb/20418.

# Do not run if gdb debug is enabled as it doesn't work for separate-mi-tty.
if [gdb_debug_enabled] {
    untested "debug is enabled"
    return 0
}

load_lib mi-support.exp

standard_testfile

if {[build_executable $testfile.exp $testfile ${srcfile} "debug"] == -1} {
    untested "failed to compile"
    return -1
}

# The test driver.  SYNC_COMMAND specifies which command is used to
# synchronously start the program running.

proc do_test {sync_command} {
    global srcdir subdir binfile srcfile
    global gdb_spawn_id gdb_main_spawn_id mi_spawn_id inferior_spawn_id
    global gdb_prompt mi_gdb_prompt

    mi_gdb_exit

    if {[mi_gdb_start "separate-mi-tty"] != 0} {
	fail "could not start gdb"
	return
    }

    mi_delete_breakpoints
    mi_gdb_reinitialize_dir $srcdir/$subdir
    mi_gdb_load $binfile

    # Start a synchronous run/continue on the MI UI.
    set test "send synchronous execution command"
    if {$sync_command == "run"} {
	if {[mi_run_cmd] >= 0} {
	    pass $test
	} else {
	    return
	}
    } else {
	if {[mi_runto_main] < 0} {
	    return
	}
	if {[mi_send_resuming_command_raw "123-exec-continue" $test] >= 0} {
	    pass $test
	} else {
	    return
	}
    }

    # Send -thread-info immediately after.  If everything works
    # correctly, this is only serviced by GDB when the execution
    # stops.
    send_gdb "456-thread-info\n"
    pass "send -thread-info"

    # Make sure we trigger an asynchronous event (=thread-group-added)
    # in the separate MI UI.  Note the "run" variant usually triggers
    # =thread-group-started/=thread-created/=library-loaded as well.
    with_spawn_id $gdb_main_spawn_id {
	gdb_test "add-inferior" "Added inferior 2 on connection .*"
    }

    # Interrupt the program.
    with_spawn_id $gdb_main_spawn_id {
	set message "interrupt on the CLI"
	gdb_test_multiple "interrupt" "$message" {
	    -re "$gdb_prompt " {
		gdb_test_multiple "" "$message" {
		    -re "received signal SIGINT" {
			pass $message
		    }
		}
	    }
	}
    }

    # On the MI channel, we should see the interrupt output _before_
    # the -thread-info output.
    with_spawn_id $mi_spawn_id {
	mi_expect_interrupt "got MI interrupt output"
    }

    # Look for the result of our -thread-info.  If input were
    # re-enabled too soon, the thread would incorrectly show up with
    # state="running".
    with_spawn_id $mi_spawn_id {
	mi_gdb_test "" "456\\^.*state=\"stopped\".*" \
	    "got -thread-info output and thread is stopped"
    }
}

foreach_with_prefix sync-command {"run" "continue"} {
    do_test ${sync-command}
}