From 43bbd567f2d928b2628e508ee9c75a3920e26b4d Mon Sep 17 00:00:00 2001 From: "K. Richard Pixley" Date: Tue, 8 Dec 1992 04:59:31 +0000 Subject: recording file death --- gdb/doc/gdbinv-s.m4 | 427 ---------------------------------------------------- 1 file changed, 427 deletions(-) (limited to 'gdb/doc/gdbinv-s.m4') diff --git a/gdb/doc/gdbinv-s.m4 b/gdb/doc/gdbinv-s.m4 index e0814be..e69de29 100755 --- a/gdb/doc/gdbinv-s.m4 +++ b/gdb/doc/gdbinv-s.m4 @@ -1,427 +0,0 @@ -_dnl__ -*- Texinfo -*- -_dnl__ Copyright (c) 1990 1991 Free Software Foundation, Inc. -_dnl__ This file is part of the source for the GDB manual. -@c M4 FRAGMENT $Id$ -@c This text diverted to "Remote Debugging" section in general case; -@c however, if we're doing a manual specifically for one of these, it -@c belongs up front (in "Getting In and Out" chapter). -_if__(_I960__) -_if__(!_GENERIC__) -@node i960-Nindy Remote, EB29K Remote, Mode Options, Starting _GDBN__ -_fi__(!_GENERIC__) -_if__(_GENERIC__) -@node i960-Nindy Remote, EB29K Remote, Remote, Remote -_fi__(_GENERIC__) -@subsection _GDBN__ with a Remote i960 (Nindy) - -@cindex Nindy -@cindex i960 -@dfn{Nindy} is a ROM Monitor program for Intel 960 target systems. When -_GDBN__ is configured to control a remote Intel 960 using Nindy, you can -tell _GDBN__ how to connect to the 960 in several ways: - -@itemize @bullet -@item -Through command line options specifying serial port, version of the -Nindy protocol, and communications speed; - -@item -By responding to a prompt on startup; - -@item -By using the @code{target} command at any point during your _GDBN__ -session. @xref{Target Commands}. - -@end itemize - -@menu -* Nindy Startup:: Startup with Nindy -* Nindy Options:: Options for Nindy -* Nindy reset:: Nindy Reset Command -@end menu - -@node Nindy Startup, Nindy Options, i960-Nindy Remote, i960-Nindy Remote -@subsubsection Startup with Nindy - -If you simply start @code{_GDBN__} without using any command-line -options, you are prompted for what serial port to use, @emph{before} you -reach the ordinary _GDBN__ prompt: -@example -Attach /dev/ttyNN -- specify NN, or "quit" to quit: -@end example -@noindent -Respond to the prompt with whatever suffix (after @samp{/dev/tty}) -identifies the serial port you want to use. You can, if you choose, -simply start up with no Nindy connection by responding to the prompt -with an empty line. If you do this, and later wish to attach to Nindy, -use @code{target} (@pxref{Target Commands}). - -@node Nindy Options, Nindy reset, Nindy Startup, i960-Nindy Remote -@subsubsection Options for Nindy - -These are the startup options for beginning your _GDBN__ session with a -Nindy-960 board attached: - -@table @code -@item -r @var{port} -Specify the serial port name of a serial interface to be used to connect -to the target system. This option is only available when _GDBN__ is -configured for the Intel 960 target architecture. You may specify -@var{port} as any of: a full pathname (e.g. @samp{-r /dev/ttya}), a -device name in @file{/dev} (e.g. @samp{-r ttya}), or simply the unique -suffix for a specific @code{tty} (e.g. @samp{-r a}). - -@item -O -(An uppercase letter ``O'', not a zero.) Specify that _GDBN__ should use -the ``old'' Nindy monitor protocol to connect to the target system. -This option is only available when _GDBN__ is configured for the Intel 960 -target architecture. - -@quotation -@emph{Warning:} if you specify @samp{-O}, but are actually trying to -connect to a target system that expects the newer protocol, the connection -will fail, appearing to be a speed mismatch. _GDBN__ will repeatedly -attempt to reconnect at several different line speeds. You can abort -this process with an interrupt. -@end quotation - -@item -brk -Specify that _GDBN__ should first send a @code{BREAK} signal to the target -system, in an attempt to reset it, before connecting to a Nindy target. - -@quotation -@emph{Warning:} Many target systems do not have the hardware that this -requires; it only works with a few boards. -@end quotation - -@end table - -The standard @samp{-b} option controls the line speed used on the serial -port. - -@node Nindy reset, , Nindy Options, i960-Nindy Remote -@c @group -@subsubsection Nindy Reset Command -@table @code -@item reset -@kindex reset -For a Nindy target, this command sends a ``break'' to the remote target -system; this is only useful if the target has been equipped with a -circuit to perform a hard reset (or some other interesting action) when -a break is detected. -@end table -@c @end group -_fi__(_I960__) - -_if__(_AMD29K__) -_if__(!_GENERIC__) -@node EB29K Remote, VxWorks Remote, i960-Nindy Remote, Starting _GDBN__ -_fi__(!_GENERIC__) -_if__(_GENERIC__) -@node EB29K Remote, VxWorks Remote, i960-Nindy Remote, Remote -_fi__(_GENERIC__) -@subsection _GDBN__ with a Remote EB29K - -@cindex EB29K board -@cindex running 29K programs - -To use _GDBN__ from a Unix system to run programs on AMD's EB29K -board in a PC, you must first connect a serial cable between the PC -and a serial port on the Unix system. In the following, we assume -you've hooked the cable between the PC's @file{COM1} port and -@file{/dev/ttya} on the Unix system. - -@menu -* Comms (EB29K):: Communications Setup -* _GDBP__-EB29K:: EB29K cross-debugging -* Remote Log:: Remote Log -@end menu - -@node Comms (EB29K), _GDBP__-EB29K, EB29K Remote, EB29K Remote -@subsubsection Communications Setup -The next step is to set up the PC's port, by doing something like the -following in DOS on the PC: -_0__@example -C:\> MODE com1:9600,n,8,1,none -_1__@end example -@noindent -This example---run on an MS DOS 4.0 system---sets the PC port to 9600 -bps, no parity, eight data bits, one stop bit, and no ``retry'' action; -you must match the communications parameters when establishing the Unix -end of the connection as well. -@c FIXME: Who knows what this "no retry action" crud from the DOS manual may -@c mean? It's optional; leave it out? ---pesch@cygnus.com, 25feb91 - -To give control of the PC to the Unix side of the serial line, type -the following at the DOS console: -_0__@example -C:\> CTTY com1 -_1__@end example -@noindent -(Later, if you wish to return control to the DOS console, you can use -the command @code{CTTY con}---but you must send it over the device that -had control, in our example over the @file{COM1} serial line). - -From the Unix host, use a communications program such as @code{tip} or -@code{cu} to communicate with the PC; for example, -@example -cu -s 9600 -l /dev/ttya -@end example -@noindent -The @code{cu} options shown specify, respectively, the linespeed and the -serial port to use. If you use @code{tip} instead, your command line -may look something like the following: -@example -tip -9600 /dev/ttya -@end example -@noindent -Your system may define a different name where our example uses -@file{/dev/ttya} as the argument to @code{tip}. The communications -parameters, including what port to use, are associated with the -@code{tip} argument in the ``remote'' descriptions file---normally the -system table @file{/etc/remote}. -@c FIXME: What if anything needs doing to match the "n,8,1,none" part of -@c the DOS side's comms setup? cu can support -o (odd -@c parity), -e (even parity)---apparently no settings for no parity or -@c for character size. Taken from stty maybe...? John points out tip -@c can set these as internal variables, eg ~s parity=none; man stty -@c suggests that it *might* work to stty these options with stdin or -@c stdout redirected... ---pesch@cygnus.com, 25feb91 - -@kindex EBMON -Using the @code{tip} or @code{cu} connection, change the DOS working -directory to the directory containing a copy of your 29K program, then -start the PC program @code{EBMON} (an EB29K control program supplied -with your board by AMD). You should see an initial display from -@code{EBMON} similar to the one that follows, ending with the -@code{EBMON} prompt @samp{#}--- -_0__@example -C:\> G: - -G:\> CD \usr\joe\work29k - -G:\USR\JOE\WORK29K> EBMON -Am29000 PC Coprocessor Board Monitor, version 3.0-18 -Copyright 1990 Advanced Micro Devices, Inc. -Written by Gibbons and Associates, Inc. - -Enter '?' or 'H' for help - -PC Coprocessor Type = EB29K -I/O Base = 0x208 -Memory Base = 0xd0000 - -Data Memory Size = 2048KB -Available I-RAM Range = 0x8000 to 0x1fffff -Available D-RAM Range = 0x80002000 to 0x801fffff - -PageSize = 0x400 -Register Stack Size = 0x800 -Memory Stack Size = 0x1800 - -CPU PRL = 0x3 -Am29027 Available = No -Byte Write Available = Yes - -# ~. -_1__@end example - -Then exit the @code{cu} or @code{tip} program (done in the example by -typing @code{~.} at the @code{EBMON} prompt). @code{EBMON} will keep -running, ready for _GDBN__ to take over. - -For this example, we've assumed what is probably the most convenient -way to make sure the same 29K program is on both the PC and the Unix -system: a PC/NFS connection that establishes ``drive @code{G:}'' on the -PC as a file system on the Unix host. If you don't have PC/NFS or -something similar connecting the two systems, you must arrange some -other way---perhaps floppy-disk transfer---of getting the 29K program -from the Unix system to the PC; _GDBN__ will @emph{not} download it over the -serial line. - -@node _GDBP__-EB29K, Remote Log, Comms (EB29K), EB29K Remote -@subsubsection EB29K cross-debugging -Finally, @code{cd} to the directory containing an image of your 29K -program on the Unix system, and start _GDBN__---specifying as argument the -name of your 29K program: -@example -cd /usr/joe/work29k -_GDBP__ myfoo -@end example -Now you can use the @code{target} command: -@example -target amd-eb /dev/ttya 9600 MYFOO -@end example -@c FIXME: test above 'target amd-eb' as spelled, with caps! caps are meant to -@c emphasize that this is the name as seen by DOS (since I think DOS is -@c single-minded about case of letters). ---pesch@cygnus.com, 25feb91 - -@noindent -In this example, we've assumed your program is in a file called -@file{myfoo}. Note that the filename given as the last argument to -@code{target amd-eb} should be the name of the program as it appears to DOS. -In our example this is simply @code{MYFOO}, but in general it can include -a DOS path, and depending on your transfer mechanism may not resemble -the name on the Unix side. - -At this point, you can set any breakpoints you wish; when you're ready -to see your program run on the 29K board, use the _GDBN__ command -@code{run}. - -To stop debugging the remote program, use the _GDBN__ @code{detach} -command. - -To return control of the PC to its console, use @code{tip} or @code{cu} -once again, after your _GDBN__ session has concluded, to attach to -@code{EBMON}. You can then type the command @code{q} to shut down -@code{EBMON}, returning control to the DOS command-line interpreter. -Type @code{CTTY con} to return command input to the main DOS console, -and type @kbd{~.} to leave @code{tip} or @code{cu}. - -@node Remote Log, , _GDBP__-EB29K, EB29K Remote -@subsubsection Remote Log -@kindex eb.log -@cindex log file for EB29K -The @code{target amd-eb} command creates a file @file{eb.log} in the -current working directory, to help debug problems with the connection. -@file{eb.log} records all the output from @code{EBMON}, including echoes -of the commands sent to it. Running @samp{tail -f} on this file in -another window often helps to understand trouble with @code{EBMON}, or -unexpected events on the PC side of the connection. -_fi__(_AMD29K__) - -_if__(_VXWORKS__) -_if__(!_GENERIC__) -@node VxWorks Remote, , EB29K Remote, Starting _GDBN__ -_fi__(!_GENERIC__) -_if__(_GENERIC__) -@node VxWorks Remote, , EB29K Remote, Remote -_fi__(_GENERIC__) -@subsection _GDBN__ and VxWorks -@cindex VxWorks -_GDBN__ enables developers to spawn and debug tasks running on networked -VxWorks targets from a Unix host. Already-running tasks spawned from -the VxWorks shell can also be debugged. _GDBN__ uses code that runs on -both the UNIX host and on the VxWorks target. The program -@code{_GDBP__} is installed and executed on the UNIX host. - -The remote debugging interface (RDB) routines are installed and executed -on the VxWorks target. These routines are included in the VxWorks library -@file{rdb.a} and are incorporated into the system image when source-level -debugging is enabled in the VxWorks configuration. - -@kindex INCLUDE_RDB -You can define @code{INCLUDE_RDB} in the VxWorks configuration file -@file{configAll.h} to include the RDB interface routines and spawn the -source debugging task @code{tRdbTask} when VxWorks is booted. For more -information on configuring and remaking VxWorks, see the @cite{VxWorks -Programmer's Guide}. - -Once you have included the RDB interface in your VxWorks system image -and set your Unix execution search path to find _GDBN__, you are ready -to run _GDBN__. From your UNIX host, type: - -@smallexample -% _GDBP__ -@end smallexample - -_GDBN__ will come up showing the prompt: - -@smallexample -(_GDBP__) -@end smallexample - -@menu -* VxWorks connection:: Connecting to VxWorks -* VxWorks download:: VxWorks Download -* VxWorks attach:: Running Tasks -@end menu - -@node VxWorks connection, VxWorks download, VxWorks Remote, VxWorks Remote -@subsubsection Connecting to VxWorks - -The _GDBN__ command @code{target} lets you connect to a VxWorks target on the -network. To connect to a target whose host name is ``@code{tt}'', type: - -@smallexample -(_GDBP__) target vxworks tt -@end smallexample - -_GDBN__ will display a message similar to the following: - -@smallexample -Attaching remote machine across net... Success! -@end smallexample - -_GDBN__ will then attempt to read the symbol tables of any object -modules loaded into the VxWorks target since it was last booted. -_GDBN__ locates these files by searching the directories listed in the -command search path (@pxref{Environment}); if it fails to find an -object file, it will display a message such as: - -@smallexample -prog.o: No such file or directory. -@end smallexample - -This will cause the @code{target} command to abort. When this happens, -you should add the appropriate directory to the search path, with the -_GDBN__ command @code{path}, and execute the @code{target} command -again. - -@node VxWorks download, VxWorks attach, VxWorks connection, VxWorks Remote -@subsubsection VxWorks Download - -@cindex download to VxWorks -If you have connected to the VxWorks target and you want to debug an -object that has not yet been loaded, you can use the _GDBN__ @code{load} -command to download a file from UNIX to VxWorks incrementally. The -object file given as an argument to the @code{load} command is actually -opened twice: first by the VxWorks target in order to download the code, -then by _GDBN__ in order to read the symbol table. This can lead to -problems if the current working directories on the two systems differ. -It is simplest to set the working directory on both systems to the -directory in which the object file resides, and then to reference the -file by its name, without any path. Thus, to load a program -@file{prog.o}, residing in @file{wherever/vw/demo/rdb}, on VxWorks type: - -@smallexample --> cd "wherever/vw/demo/rdb" -@end smallexample - -On _GDBN__ type: - -@smallexample -(_GDBP__) cd wherever/vw/demo/rdb -(_GDBP__) load prog.o -@end smallexample - -_GDBN__ will display a response similar to the following: - -@smallexample -Reading symbol data from wherever/vw/demo/rdb/prog.o... done. -@end smallexample - -You can also use the @code{load} command to reload an object module -after editing and recompiling the corresponding source file. Note that -this will cause _GDBN__ to delete all currently-defined breakpoints, -auto-displays, and convenience variables, and to clear the value -history. (This is necessary in order to preserve the integrity of -debugger data structures that reference the target system's symbol -table.) - -@node VxWorks attach, , VxWorks download, VxWorks Remote -@subsubsection Running Tasks - -@cindex running VxWorks tasks -You can also attach to an existing task using the @code{attach} command as -follows: - -@smallexample -(_GDBP__) attach @var{task} -@end smallexample - -where @var{task} is the VxWorks hexadecimal task ID. The task can be running -or suspended when you attach to it. If running, it will be suspended at -the time of attachment. - -_fi__(_VXWORKS__) -- cgit v1.1