| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The 4-byte VSCR register is found inside a 16-byte field in the regset
returned by ptrace and in core files. The position of VSCR depends on
the endianess of the target, which was previously assumed to be
big-endian for the purpose of getting VSCR. This patch removes this
assumption to fix access to VSCR in little-endian mode.
gdb/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* ppc-tdep.h (struct ppc_reg_offsets): Remove vector register
offset fields.
* ppc-fbsd-tdep.c (ppc32_fbsd_reg_offsets): Remove initializers
for vector register offset fields.
(ppc64_fbsd_reg_offsets): Likewise.
* ppc-nbsd-tdep.c (_initialize_ppcnbsd_tdep): Remove assignment
to vector register offset fields.
* ppc-obsd-tdep.c (_initialize_ppcnbsd_tdep): Remove assignment
to vector register offset fields.
* ppc-obsd-nat.c (_initialize_ppcobsd_nat): Remove assignment to
vector register offset fields.
* rs6000-aix-tdep.c (rs6000_aix32_reg_offsets): Remove
initializers for vector register offset fields.
(rs6000_aix64_reg_offsets): Likewise.
* rs6000-tdep.c (ppc_vrreg_offset): Remove.
(ppc_supply_vrregset): Remove.
(ppc_collect_vrregset): Remove.
* ppc-linux-tdep.c (ppc_linux_collect_vrregset): New function.
(ppc_linux_vrregset) : New function.
(ppc32_le_linux_vrregmap, ppc32_be_linux_vrregmap)
(ppc32_le_linux_vrregset, ppc32_be_linux_vrregset): New globals.
(ppc32_linux_vrregset): Remove.
(ppc_linux_iterate_over_regset_sections): Call ppc_linux_vrregset
and use result instead of ppc32_linux_vrregset.
(ppc32_linux_reg_offsets): Remove initializers for vector register
offset fields.
(ppc64_linux_reg_offsets): Likewise.
* ppc-linux-tdep.h (ppc_linux_vrregset): New declaration.
* ppc-linux-nat.c: Include regset.h.
(gdb_vrregset_t): Adjust comment to account for little-endian
mode.
(supply_vrregset, fill_vrregset): Remove.
(fetch_altivec_register, store_altivec_register): Remove.
(fetch_altivec_registers): Add regno parameter. Get regset using
ppc_linux_vrregset. Use regset to supply registers.
(store_altivec_registers): Add regno parameter. Get regset using
ppc_linux_vrregset. Use regset to collect registers.
(fetch_register): Call fetch_altivec_registers instead of
fetch_altivec_register.
(store_register): Call store_altivec_registers instead of
store_altivec_register.
(fetch_ppc_registers): Call fetch_altivec_registers with -1 for
the new regno parameter.
(store_ppc_registers): Call store_altivec_registers with -1 for
the new regno parameter.
gdb/gdbserver/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* linux-ppc-low.c (ppc_fill_vrregset): Add vscr_offset variable.
Set vscr_offset to 0 in little-endian mode and 12 in big-endian
mode. Call collect_register_by_name with vscr using
vscr_offset. Zero-pad vscr and vrsave fields in collector buffer.
(ppc_store_vrregset): Add and set vscr_offset variable as in
ppc_fill_vrregset. Call supply_register_by_name with vscr using
vscr_offset.
|
|
This patch defines constants for the sizes of the two vector
regsets (vector-scalar registers and regular vector registers).
The native, gdbserver and core file targets are changed to use these
constants.
The Linux ptrace calls return (or read) a smaller regset than the one
found in core files for vector registers, because ptrace uses a single
4-byte quantity for vrsave at the end of the regset, while the
core-file regset uses a full 16-byte field for vrsave. For simplicity,
the larger size is used in both cases, and so a buffer with 12 unused
additional bytes is passed to ptrace in the native target.
gdb/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* arch/ppc-linux-common.h (PPC_LINUX_SIZEOF_VRREGSET)
(PPC_LINUX_SIZEOF_VSXREGSET): Define.
* ppc-linux-nat.c (SIZEOF_VSXREGS, SIZEOF_VRREGS): Remove.
(gdb_vrregset_t): Change array type size to
PPC_LINUX_SIZEOF_VRREGSET.
(gdb_vsxregset_t): Change array type size to
PPC_LINUX_SIZEOF_VSXREGSET.
* ppc-linux-tdep.c (ppc_linux_iterate_over_regset_sections):
Change integer literals to PPC_LINUX_SIZEOF_VRREGSET and
PPC_LINUX_SIZEOF_VSXREGSET.
gdb/gdbserver/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* linux-ppc-low.c (SIZEOF_VSXREGS, SIZEOF_VRREGS): Remove.
(ppc_arch_setup): Change SIZEOF_VRREGS and SIZEOF_VSXREGS to
PPC_LINUX_SIZEOF_VRREGSET and PPC_LINUX_SIZEOF_VSXREGSET.
|
|
Currently the linux-ppc-low.c fill/store functions for extended
regsets check whether they should execute by using the global hwcap
variable.
This patch explicitly sets the regset sizes to zero when needed to
disable them instead, so that the fill/store functions are not called
in the first place by regsets_fetch_inferior_registers in linux-low.c.
gdb/gdbserver/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* linux-ppc-low.c (ppc_fill_vsxregset): Remove ppc_hwcap check.
(ppc_store_vsxregset): Likewise.
(ppc_fill_vrregset): Likewise.
(ppc_store_vrregset): Likewise.
(ppc_fill_evrregset): Likewise.
(ppc_store_evrregset): Likewise.
(ppc_regsets): Set VSX/VR/EVR regset sizes to 0.
(ppc_arch_setup): Iterate through ppc_regsets and set sizes when
needed.
|
|
This patch moves the native target wordsize getter for ppc linux to
nat/ so that it can be used to simplify ppc_arch_setup in
gdbserver. The ptrace call used to get MSR for this is ultimately the
same as before, but it is no longer necessary to create a temporary
regcache to call fetch_inferior_registers.
gdb/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* configure.nat <linux powerpc>: Add ppc-linux.o to NATDEPFILES.
* ppc-linux-nat.c (ppc_linux_target_wordsize): Move to
nat/ppc-linux.c.
(ppc_linux_nat_target::auxv_parse): Get thread id tid. Call
ppc_linux_target_wordsize with tid.
(ppc_linux_nat_target::read_description): Call ppc_linux_target
wordsize with tid.
* nat/ppc-linux.c: Include nat/gdb_ptrace.h.
(ppc64_64bit_inferior_p): Add static and inline specifiers.
(ppc_linux_target_wordsize): Move here from ppc-linux-nat.c. Add
tid parameter. Remove static specifier.
* nat/ppc-linux.h (ppc64_64bit_inferior_p): Remove declaration.
(ppc_linux_target_wordsize): New declaration.
gdb/gdbserver/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* linux-ppc-low.c (ppc_arch_setup): Remove code for getting the
wordsize of the inferior. Call ppc_linux_target_wordsize.
|
|
Share target description declarations and selection among ppc linux
native targets, core files, gdbserver and IPA.
To avoid complicated define guards, gdbserver and IPA now have
declarations for all descriptions, including 64-bit generated
descriptions when compiled in 32-bit mode. These have always been
linked into the gdbserver and IPA binaries. Because they might be
uninitialized, the selection function checks that the selected
description is initialized.
gdb/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* arch/ppc-linux-common.c: New file.
* arch/ppc-linux-common.h: New file.
* arch/ppc-linux-tdesc.h: New file.
* configure.tgt (powerpc*-*-linux*): Add arch/ppc-linux-common.o.
* Makefile.in (ALL_TARGET_OBS): Add arch/ppc-linux-common.o.
(HFILES_NO_SRCDIR): Add arch/ppc-linux-common.h and
arch/ppc-linux-tdesc.h.
* ppc-linux-nat.c: Include arch/ppc-linux-common.h and
arch/ppc-linux-tdesc.h.
(ppc_linux_nat_target::read_description): Remove target
description matching code. Fill a ppc_linux_features struct and
call ppc_linux_match_description with it. Move comment about ISA
2.05 to ppc-linux-common.c.
* ppc-linux-tdep.c: Include arch/ppc-linux-common.h and
arch/ppc-linux-tdesc.h.
(ppc_linux_core_read_description): Remove target description
matching code. Fill a ppc_linux_features struct and call
ppc_linux_match_description with it.
* ppc-linux-tdep.h (tdesc_powerpc_32l, tdesc_powerpc_64l)
(tdesc_powerpc_altivec32l, tdesc_powerpc_altivec64l)
(tdesc_powerpc_cell32l, tdesc_powerpc_cell64l)
(tdesc_powerpc_vsx32l, tdesc_powerpc_vsx64l)
(tdesc_powerpc_isa205_32l, tdesc_powerpc_isa205_64l)
(tdesc_powerpc_isa205_altivec32l, tdesc_powerpc_isa205_altivec64l)
(tdesc_powerpc_isa205_vsx32l, tdesc_powerpc_isa205_vsx64l)
(tdesc_powerpc_e500l): Remove.
gdb/gdbserver/ChangeLog:
2018-05-22 Pedro Franco de Carvalho <pedromfc@linux.vnet.ibm.com>
* configure.srv (srv_tgtobj): Add arch/ppc-linux-common.o.
* Makefile.in (SFILES): Add arch/ppc-linux-common.c.
* linux-ppc-tdesc.h: Rename to linux-ppc-tdesc-init.h.
* linux-ppc-tdesc-init.h (tdesc_powerpc_32l, tdesc_powerpc_64l)
(tdesc_powerpc_altivec32l, tdesc_powerpc_altivec64l)
(tdesc_powerpc_cell32l, tdesc_powerpc_cell64l)
(tdesc_powerpc_vsx32l, tdesc_powerpc_vsx64l)
(tdesc_powerpc_isa205_32l, tdesc_powerpc_isa205_64l)
(tdesc_powerpc_isa205_altivec32l, tdesc_powerpc_isa205_altivec64l)
(tdesc_powerpc_isa205_vsx32l, tdesc_powerpc_isa205_vsx64l)
(tdesc_powerpc_e500l): Remove.
* linux-ppc-ipa.c: Include arch/ppc-linux-tdesc.h and
linux-ppc-tdesc-init.h. Don't include linux-ppc-tdesc.h.
* linux-ppc-low.c: Include arch/ppc-linux-common.h,
arch/ppc-linux-tdesc.h, and linux-ppc-tdesc-init.h. Don't include
linux-ppc-tdesc.h.
(ppc_arch_setup): Remove target description matching code. Fill a
ppc_linux_features struct and call ppc_linux_match_description
with it.
|
|
On the MIPS target DSP ASE registers can only be accessed with the
PTRACE_PEEKUSR and PTRACE_POKEUSR `ptrace' requests. With the n32 ABI
these requests only pass 32-bit data quantities, which are narrower than
the width of DSP accumulator registers, which are 64-bit.
Generic code is prepared to transfer registers wider than the `ptrace'
data type by offsetting into the USR address space, by the data width
transferred. That however does not work with the MIPS target, because
of how the API has been defined, where USR register addresses are
actually indices rather than offsets. Consequently given address `a'
using `a + 4' accesses the fourth next register rather than the upper
half of the original register.
With native debugging this causes clobbered register contents, as well
as access failures as locations beyond the available USR space are
addressed:
(gdb) info registers
zero at v0 v1
R0 0000000000000000 0000000000000001 0000000000000001 0000000000000000
a0 a1 a2 a3
R4 0000000010019158 0000000000000000 0000000000000011 0000000010019160
a4 a5 a6 a7
R8 0000000010019160 fffffffffff00000 fffffffffffffff8 0000000000000000
t0 t1 t2 t3
R12 0000000010019150 0000000000000001 0000000000000001 000000000000000f
s0 s1 s2 s3
R16 0000000077ee6f20 0000000010007bb0 0000000000000000 0000000000000000
s4 s5 s6 s7
R20 000000000052e668 000000000052f008 0000000000000000 0000000000000000
t8 t9 k0 k1
R24 0000000000000001 0000000010019010 0000000000000000 0000000000000000
gp sp s8 ra
R28 0000000010020280 000000007fff4c10 000000007fff4c10 0000000010004f48
status lo hi badvaddr
0000000000109cf3 0000000000943efe 000000000000000e 000000001001900c
cause pc
0000000000800024 0000000010004f48
fcsr fir hi1 lo1
0e800000 00f30000 0000000004040404 0101010105050505
hi2 lo2 hi3 lo3
0202020255aa33cc Couldn't read register (#75): Input/output error.
(gdb)
With `gdbserver' this makes debugging impossible due to a fatal failure:
(gdb) target remote :2346
Remote debugging using :2346
Reading symbols from .../sysroot/mips-r2-hard/lib32/ld.so.1...done.
0x77fc3d50 in __start () from .../sysroot/mips-r2-hard/lib32/ld.so.1
(gdb) continue
Continuing.
warning: Remote failure reply: E01
Remote communication error. Target disconnected.: Connection reset by peer.
(gdb)
Correct the problem by marking any register in the MIPS backend whose
width exceeds the width of the `ptrace' data type unavailable for the
purpose of PTRACE_PEEKUSR and PTRACE_POKEUSR requests:
(gdb) info registers
zero at v0 v1
R0 0000000000000000 0000000000000001 0000000000000001 0000000000000000
a0 a1 a2 a3
R4 0000000010019158 0000000000000000 0000000000000011 0000000010019160
a4 a5 a6 a7
R8 0000000010019160 fffffffffff00000 fffffffffffffff8 0000000000000000
t0 t1 t2 t3
R12 0000000010019150 0000000000000001 0000000000000001 000000000000000f
s0 s1 s2 s3
R16 0000000077ee6f20 0000000010007bb0 0000000000000000 0000000000000000
s4 s5 s6 s7
R20 000000000052e5c8 000000000052f008 0000000000000000 0000000000000000
t8 t9 k0 k1
R24 0000000000000001 0000000010019010 0000000000000000 0000000000000000
gp sp s8 ra
R28 0000000010020280 000000007fff4be0 000000007fff4be0 0000000010004f48
status lo hi badvaddr
0000000000109cf3 0000000000943efe 000000000000000e 000000001001900c
cause pc
0000000000800024 0000000010004f48
fcsr fir hi1 lo1
0e800000 00f30000 <unavailable> <unavailable>
hi2 lo2 hi3 lo3
<unavailable> <unavailable> <unavailable> <unavailable>
dspctl restart
55aa33cc 0000000000000000
(gdb)
as there is no way to access full contents of these registers with the
limited API available anyway.
This obviously does not affect general-purpose registers (which use the
PTRACE_GETREGS and PTRACE_SETREGS requests for access) or floating-point
general registers (which use PTRACE_GETFPREGS and PTRACE_SETFPREGS).
And $dspctl, being 32-bit, remains accessible too, which is important
for BPOSGE32 branch decoding in single-stepping.
For DSP accumulator access with the n32 ABI a new `ptrace' API is required
on the kernel side.
gdb/
* mips-linux-nat.c (mips64_linux_register_addr): Return -1 if
the width of the requested register exceeds the width of the
`ptrace' data type.
gdb/gdbserver/
* linux-mips-low.c (mips_cannot_fetch_register): Return 1 if the
width of the requested register exceeds the width of the
`ptrace' data type.
(mips_cannot_store_register): Likewise.
|
|
Consistently supply hardwired $zero as a zeroed register, correcting
issues with the PTRACE_GETREGS path that currently copies the value of
$restart into $zero as illustrated by this program:
$ cat read.c
int
main (void)
{
char buf[1024];
ssize_t size;
size = read (0, buf, sizeof (buf));
return size;
}
$
and this corresponding debug session:
(gdb) break main
Breakpoint 1 at 0x120000970: file read.c, line 9.
(gdb) target remote :2346
Remote debugging using :2346
Reading symbols from .../sysroot/mips-r2-hard/lib64/ld.so.1...done.
0x000000fff7fca5a0 in __start ()
from .../sysroot/mips-r2-hard/lib64/ld.so.1
(gdb) continue
Continuing.
Breakpoint 1, main () at read.c:9
9 size = read (0, buf, sizeof (buf));
(gdb) info registers
zero at v0 v1
R0 0000000000000000 0000000000000001 000000fff7ffe710 0000000000000000
a0 a1 a2 a3
R4 0000000000000001 000000ffffffeb88 000000ffffffeb98 0000000000000000
a4 a5 a6 a7
R8 000000fff7fc8800 000000fff7fc38f0 000000ffffffeb80 2f2f2f2f2f2f2f2f
t0 t1 t2 t3
R12 0000000000000437 0000000000000002 000000fff7ffd000 0000000120000a00
s0 s1 s2 s3
R16 000000fff7fc7068 0000000120000b90 0000000000000000 0000000000000000
s4 s5 s6 s7
R20 0000000000521d88 0000000000522608 0000000000000000 0000000000000000
t8 t9 k0 k1
R24 0000000000000000 0000000120000970 0000000000000000 0000000000000000
gp sp s8 ra
R28 000000fff7fc8800 000000ffffffea50 0000000000000000 000000fff7e4088c
status lo hi badvaddr
0000000000109cf3 0000000000005ea5 0000000000000211 000000fff7eadf00
cause pc
0000000000800024 0000000120000970
fcsr fir restart
00000000 00f30000 0000000000000000
(gdb) continue
Continuing.
^C
Program received signal SIGINT, Interrupt.
0x000000fff7f084ac in __GI___libc_read (fd=0, buf=0xffffffe640, nbytes=1024)
at ../sysdeps/unix/sysv/linux/read.c:27
27 return SYSCALL_CANCEL (read, fd, buf, nbytes);
(gdb) info registers
zero at v0 v1
R0 0000000000001388 0000000000000001 0000000000000200 000000fff7ffe710
a0 a1 a2 a3
R4 0000000000000000 000000ffffffe640 0000000000000400 0000000000000001
a4 a5 a6 a7
R8 000000fff7fc8800 000000fff7fc38f0 000000ffffffeb80 2f2f2f2f2f2f2f2f
t0 t1 t2 t3
R12 00000000000005e3 0000000000000002 000000fff7ffd000 000000012000099c
s0 s1 s2 s3
R16 000000fff7fc7068 0000000120000b90 0000000000000000 0000000000000000
s4 s5 s6 s7
R20 0000000000521d88 0000000000522608 0000000000000000 0000000000000000
t8 t9 k0 k1
R24 0000000000000000 000000fff7f2da20 0000000000000000 0000000000000000
gp sp s8 ra
R28 000000fff7fc8800 000000ffffffe600 0000000000000000 000000012000099c
status lo hi badvaddr
0000000000109cf3 00000000000001e6 00000000000000be 000000fff7f08470
cause pc
0000000000800020 000000fff7f084ac
fcsr fir restart
00000000 00f30000 0000000000001388
(gdb)
and with the PTRACE_PEEKUSR path that does not supply this register at
all, causing issues analogous to ones addressed for the native MIPS
backend with commit 4e6ff0e1b86f ("MIPS/Linux/native: Supply $zero for
the !PTRACE_GETREGS case"):
(gdb) info registers
zero at v0 v1
R0 <unavailable> 0000000000000001 0000000000000001 0000000000000000
a0 a1 a2 a3
R4 00000001200212b0 0000000000000000 0000000000000021 000000012001a260
a4 a5 a6 a7
R8 000000012001a260 0000000000000004 800000010cab1680 fffffffffffffff8
t0 t1 t2 t3
R12 0000000000000000 000000fff7edab68 0000000000000001 0000000000000000
s0 s1 s2 s3
R16 000000fff7ee2068 0000000120008b80 0000000000000000 0000000000000000
s4 s5 s6 s7
R20 000000000052e5c8 000000000052f008 0000000000000000 0000000000000000
t8 t9 k0 k1
R24 0000000000000000 00000001200027c0 0000000000000000 0000000000000000
gp sp s8 ra
R28 00000001200212b0 000000ffffffc880 000000ffffffc880 0000000120005ee8
status lo hi badvaddr
<unavailable> 0000000000943efe 000000000000000e 000000012001a008
cause pc
0000000000800024 0000000120005ee8
fcsr fir restart
0e800000 00f30000 0000000000000000
(gdb)
and (under certain circumstances):
(gdb) next
Register 0 is not available
(gdb)
The problem with PTRACE_GETREGS happens because `mips_store_gregset'
supplies the contents of register slot #0, occupied by $restart, to
$zero. The problem with PTRACE_PEEKUSR happens because for $zero
`mips_cannot_fetch_register' returns one, and no alternative way to
supply that register has been defined.
Correct `mips_store_gregset' then for the PTRACE_GETREGS case and add
`mips_fetch_register' for the PTRACE_PEEKUSR case.
gdb/gdbserver/
* linux-mips-low.c (mips_fetch_register): New function. Update
preceding comment.
(mips_store_gregset): Supply 0 rather than $restart for $zero.
(the_low_target): Wire `mips_fetch_register'.
|
|
The floating point context structure on x86 LynxOS-178 is not
the same as on LynxOS 5.x. As a consequence, trying to print
the return value of a function returning a float, for instance,
yields incorrect results.
This patch fixes the issue by providing an updated definition
for LynxOS-178 (the reason why we cannot access the actual definition
provided by the system still remains true).
gdb/gdbserver/ChangeLog:
* lynx-i386-low.c (LYNXOS_178): New macro.
[LYNXOS_178] (usr_fcontext_t): Provide a definition that matches
the layout on LynxOS-178.
(lynx_i386_fill_fpregset, lynx_i386_store_fpregset): Do not
handle floating point registers that are not supported by
LynxOS-178.
|
|
Simon pointed out that gdb would not build with clang, due to the
addition of -Wimplicit-fallthrough. This patch fixes the problem by
using -Wimplicit-fallthrough=3 -- this does not work with clang,
bypassing the issue.
Tested by rebuilding with both gcc and clang; and also by verifying
that -Wimplicit-fallthrough=3 is used in the gcc build.
I will file a follow-up bug to convert the fall-through comments to a
form that can be used by both clang and gcc.
gdb/ChangeLog
2018-05-10 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
* warning.m4 (AM_GDB_WARNINGS): Use -Wimplicit-fallthrough=3.
gdb/gdbserver/ChangeLog
2018-05-10 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
|
|
On Windows, starting a new process with GDBserver seems to work,
in the sense that the program does get started, and GDBserver
confirms that it is listening for GDB to connect. However, as soon as
GDB establishes the connection with GDBserver, and starts discussing
with it, GDBserver crashes, with a SEGV.
This SEGV occurs in remote-utils.c::prepare_resume_reply...
| regp = current_target_desc ()->expedite_regs;
| [...]
| while (*regp)
... because, in our case, REGP is NULL.
This patches fixes the issues by adding a parameter to init_target_desc,
in order to make sure that we always provide the list of registers when
we initialize a target description.
gdb/ChangeLog:
PR server/23158:
* regformats/regdat.sh: Adjust script, following the addition
of the new expedite_regs parameter to init_target_desc.
gdb/gdbserver/ChangeLog:
PR server/23158:
* tdesc.h (init_target_desc) <expedite_regs>: New parameter.
* tdesc.c (init_target_desc) <expedite_regs>: New parameter.
Use it to set the expedite_regs field in the given tdesc.
* x86-tdesc.h: New file.
* linux-aarch64-tdesc.c (aarch64_linux_read_description):
Adjust following the addition of the new expedite_regs parameter
to init_target_desc.
* linux-tic6x-low.c (tic6x_read_description): Likewise.
* linux-x86-tdesc.c: #include "x86-tdesc.h".
(i386_linux_read_description, amd64_linux_read_description):
Adjust following the addition of the new expedite_regs parameter
to init_target_desc.
* lynx-i386-low.c: #include "x86-tdesc.h".
(lynx_i386_arch_setup): Adjust following the addition of the new
expedite_regs parameter to init_target_desc.
* nto-x86-low.c: #include "x86-tdesc.h".
(nto_x86_arch_setup): Adjust following the addition of the new
expedite_regs parameter to init_target_desc.
* win32-i386-low.c: #include "x86-tdesc.h".
(i386_arch_setup): Adjust following the addition of the new
expedite_regs parameter to init_target_desc.
|
|
Trying to start a program with GDBserver on Windows yields
the following error:
$ gdbserver.exe --once :4444 simple_main.exe
Killing process(es): 5008
No program to debug
Exiting
The error itself comes from the following code shortly after
create_inferior gets called (in server.c::main):
/* Wait till we are at first instruction in program. */
create_inferior (program_path.get (), program_args);
[...]
if (last_status.kind == TARGET_WAITKIND_EXITED
|| last_status.kind == TARGET_WAITKIND_SIGNALLED)
was_running = 0;
else
was_running = 1;
if (!was_running && !multi_mode)
error ("No program to debug");
What happens is that the "last_status" global starts initialized
as zeroes, which means last_status.kind == TARGET_WAITKIND_EXITED,
and we expect create_inferior to be waiting for the inferior to
start until reaching the SIGTRAP, and to set the "last_status"
global to match that last event we received.
I suspect this is an unintended side-effect of the following change...
commit 2090129c36c7e582943b7d300968d19b46160d84
Date: Thu Dec 22 21:11:11 2016 -0500
Subject: Share fork_inferior et al with gdbserver
... which removes some code in server.c that was responsible for
starting the inferior in a functin that was named start_inferior,
and looked like this:
signal_pid = create_inferior (new_argv[0], &new_argv[0]);
[...]
/* Wait till we are at 1st instruction in program, return new pid
(assuming success). */
last_ptid = mywait (pid_to_ptid (signal_pid), &last_status, 0, 0);
The code has been transitioned to using fork_inferior, but sadly,
only for the targets that support it. On Windows, the calls to wait
setting "last_status" simply disappeared.
This patch adds it back in the Windows-specific implementation of
create_inferior.
gdb/gdbserver/ChangeLog:
PR server/23158:
* win32-low.c (win32_create_inferior): Add call to my_wait
setting last_status global.
|
|
Trying to start GDBserver on Windows currently yields the following
error...
$ gdbserver.exe --once :4444 simple_main.exe
glob could not process pattern '(null)'.
Exiting
... after which GDB terminates with a nonzero status.
This is because create_process in win32-low.c calls gdb_tilde_expand
with the result of a call to get_inferior_cwd without verifying that
the returned directory is not NULL:
| static BOOL
| create_process (const char *program, char *args,
| DWORD flags, PROCESS_INFORMATION *pi)
| {
| const char *inferior_cwd = get_inferior_cwd ();
| std::string expanded_infcwd = gdb_tilde_expand (inferior_cwd);
This patch avoids this by only calling gdb_tilde_expand when
INFERIOR_CWD is not NULL, which is similar to what is done on
GNU/Linux for instance.
gdb/gdbserver/ChangeLog:
PR server/23158:
* win32-low.c (create_process): Only call gdb_tilde_expand if
inferior_cwd is not NULL.
|
|
For GNU/Linux on x86-64, if the target is using the xsave format for
passing the floating-point information from the inferior then there
currently exists a bug relating to the x87 control registers, and the
mxcsr register.
The xsave format allows different floating-point features to be lazily
enabled, a bit in the xsave format tells GDB which floating-point
features have been enabled, and which have not.
Currently in GDB, when reading the floating point state, we check the
xsave bit flags, if the feature is enabled then we read the feature
from the xsave buffer, and if the feature is not enabled, then we
supply the default value from within GDB.
Within GDB, when writing the floating point state, we first fetch the
xsave state from the target and then, for any feature that is not yet
enabled, we write the default values into the xsave buffer. Next we
compare the regcache value with the value in the xsave buffer, and, if
the value has changed we update the value in the xsave buffer, and
mark the feature enabled in the xsave bit flags.
The problem then, is that the x87 control registers were not following
this pattern. We assumed that these registers were always written out
by the kernel, and we always wrote them out to the xsave buffer (but
didn't enabled the feature). The result of this is that if the kernel
had not yet enabled the x87 feature then within GDB we would see
random values for the x87 floating point control registers, and if the
user tried to modify one of these register, that modification would be
lost.
Finally, the mxcsr register was also broken in the same way as the x87
control registers. The added complexity with this case is that the
mxcsr register is part of both the avx and sse floating point feature
set. When reading or writing this register we need to check that at
least one of these features is enabled.
This bug was present in native GDB, and within gdbserver. Both are
fixed with this commit.
gdb/ChangeLog:
* common/x86-xstate.h (I387_FCTRL_INIT_VAL): New constant.
(I387_MXCSR_INIT_VAL): New constant.
* amd64-tdep.c (amd64_supply_xsave): Only read state from xsave
buffer if it was supplied by the inferior.
* i387-tdep.c (i387_supply_fsave): Use I387_MXCSR_INIT_VAL.
(i387_xsave_get_clear_bv): New function.
(i387_supply_xsave): Only read x87 control registers from the
xsave buffer if the feature is enabled, and the state will have
been written, otherwise, provide a suitable default.
(i387_collect_xsave): Pre-clear all registers in xsave buffer,
including x87 control registers. Update control registers if they
have changed from the default value, and mark features as enabled
as required.
* i387-tdep.h (i387_xsave_get_clear_bv): Declare.
gdb/gdbserver/ChangeLog:
* i387-fp.c (i387_cache_to_xsave): Only write x87 control
registers to the cache if their values have changed.
(i387_xsave_to_cache): Provide default values for x87 control
registers when these features are available, but disabled.
* regcache.c (supply_register_by_name_zeroed): New function.
* regcache.h (supply_register_by_name_zeroed): Declare new
function.
gdb/testsuite/ChangeLog:
* gdb.arch/amd64-init-x87-values.S: New file.
* gdb.arch/amd64-init-x87-values.exp: New file.
|
|
This adds -Wduplicated-cond to warnings.m4. This caught one bug.
I tried adding -Wduplicated-branches as well, but it results in some
spurious failures from code like this in cgen.h:
#define CGEN_ATTR_TYPE(n) \
struct { unsigned int bool_; \
CGEN_ATTR_VALUE_TYPE nonbool[(n) ? (n) : 1]; }
This will trigger a warning if passed n==1, which seems like a
perfectly valid thing to do; and there were other issues like this as
well.
ChangeLog
2018-05-07 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
* warning.m4 (AM_GDB_WARNINGS): Add -Wduplicated-cond.
gdbserver/ChangeLog
2018-05-07 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
|
|
This adds -Wimplicit-fallthrough to the set of default warnings.
2018-05-04 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
* warning.m4 (AM_GDB_WARNINGS): Add -Wimplicit-fallthrough.
gdbserver/ChangeLog
2018-05-04 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
|
|
Some unaligned watchpoints were currently missed.
On old kernels as specified in
kernel RFE: aarch64: ptrace: BAS: Support any contiguous range (edit)
https://sourceware.org/bugzilla/show_bug.cgi?id=20207
after this patch some other unaligned watchpoints will get reported as false
positives.
With new kernels all the watchpoints should work exactly.
There may be a regresion that it now less merges watchpoints so that with
multiple overlapping watchpoints it may run out of the 4 hardware watchpoint
registers. But as discussed in the original thread GDB needs some generic
watchpoints merging framework to be used by all the target specific code.
Even current FSF GDB code does not merge it perfectly. Also with the more
precise watchpoints one can technically merge them less. And I do not think
it matters too much to improve mergeability only for old kernels.
Still even on new kernels some better merging logic would make sense.
There remains one issue:
kernel-4.15.14-300.fc27.armv7hl
FAIL: gdb.base/watchpoint-unaligned.exp: continue
FAIL: gdb.base/watchpoint-unaligned.exp: continue
(gdb) continue
Continuing.
Unexpected error setting watchpoint: Invalid argument.
(gdb) FAIL: gdb.base/watchpoint-unaligned.exp: continue
But that looks as a kernel bug to me.
(1) It is not a regression by this patch.
(2) It is unrelated to this patch.
gdb/ChangeLog
2018-05-04 Jan Kratochvil <jan.kratochvil@redhat.com>
Pedro Alves <palves@redhat.com>
PR breakpoints/19806 and support for PR external/20207.
* NEWS: Mention Aarch64 watchpoint improvements.
* aarch64-linux-nat.c (aarch64_linux_stopped_data_address): Fix missed
watchpoints and PR external/20207 watchpoints.
* nat/aarch64-linux-hw-point.c
(kernel_supports_any_contiguous_range): New.
(aarch64_watchpoint_offset): New.
(aarch64_watchpoint_length): Support PR external/20207 watchpoints.
(aarch64_point_encode_ctrl_reg): New parameter offset, new asserts.
(aarch64_point_is_aligned): Support PR external/20207 watchpoints.
(aarch64_align_watchpoint): New parameters aligned_offset_p and
next_addr_orig_p. Support PR external/20207 watchpoints.
(aarch64_downgrade_regs): New.
(aarch64_dr_state_insert_one_point): New parameters offset and
addr_orig.
(aarch64_dr_state_remove_one_point): Likewise.
(aarch64_handle_breakpoint): Update caller.
(aarch64_handle_aligned_watchpoint): Likewise.
(aarch64_handle_unaligned_watchpoint): Support addr_orig and
aligned_offset.
(aarch64_linux_set_debug_regs): Remove const from state. Call
aarch64_downgrade_regs.
(aarch64_show_debug_reg_state): Print also dr_addr_orig_wp.
* nat/aarch64-linux-hw-point.h (DR_CONTROL_LENGTH): Rename to ...
(DR_CONTROL_MASK): ... this.
(struct aarch64_debug_reg_state): New field dr_addr_orig_wp.
(unsigned int aarch64_watchpoint_offset): New prototype.
(aarch64_linux_set_debug_regs): Remove const from state.
* utils.c (align_up, align_down): Move to ...
* common/common-utils.c (align_up, align_down): ... here.
* utils.h (align_up, align_down): Move to ...
* common/common-utils.h (align_up, align_down): ... here.
gdb/gdbserver/ChangeLog
2018-05-04 Jan Kratochvil <jan.kratochvil@redhat.com>
Pedro Alves <palves@redhat.com>
* linux-aarch64-low.c (aarch64_stopped_data_address):
Likewise.
gdb/testsuite/ChangeLog
2018-05-04 Jan Kratochvil <jan.kratochvil@redhat.com>
Pedro Alves <palves@redhat.com>
PR breakpoints/19806 and support for PR external/20207.
* gdb.base/watchpoint-unaligned.c: New file.
* gdb.base/watchpoint-unaligned.exp: New file.
|
|
I noticed the existence of -Wsuggest-override and so this patch
enables it for gdb. It found a few spots that could use "override".
Also I went ahead and removed all uses of the "OVERRIDE" macro.
Using override is beneficial because it makes it harder to change a
base class and then forget to change a derived class.
Tested by the buildbot.
ChangeLog
2018-04-27 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
* warning.m4 (AM_GDB_WARNINGS): Add -Wsuggest-override.
* dwarf2loc.c (class dwarf_evaluate_loc_desc): Use "override", not
"OVERRIDE".
(class symbol_needs_eval_context): Likewise.
* dwarf2read.c (mock_mapped_index::symbol_name_count)
(mock_mapped_index::symbol_name_at): Use "override". Remove
"virtual".
* dwarf2-frame.c (dwarf_expr_executor::get_addr_index): Use
"override".
(class dwarf_expr_executor): Use "override", not "OVERRIDE".
* aarch64-tdep.c (instruction_reader::read): Use "override".
(instruction_reader_test::read): Likewise.
* arm-tdep.c (instruction_reader::read): Use "override".
(instruction_reader_thumb::read): Likewise.
gdbserver/ChangeLog
2018-04-27 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
|
|
Pedro pointed out that gdb/configure and gdbserver/configure weren't
updated after some recent *.m4 changes.
This patch rebuilds those files. Tested by rebuilding. Pedro
approved this in the thread where he raised this issue, so I'm pushing
it in.
ChangeLog
2018-04-23 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
gdbserver/ChangeLog
2018-04-23 Tom Tromey <tom@tromey.com>
* configure: Rebuild.
|
|
The dependency tracking (the thing that knows which source file included
which other source file during last build to know what to rebuild when
an included file changes) is broken for gdbserver subdirectories (arch
and common).
The dependency tracking files are created in the form
arch/.deps/i386.Po
but we try to include
.deps/arch/i386.Po
An easy smoke test is too "touch" the gdb/features/i386/32bit-core.c
file in the source directory and try to rebuild gdbserver. This file is
included by gdb/arch/i386.c, so it should cause
gdb/gdbserver/arch/i386.o in the build directory to be rebuilt. It
currently isn't rebuilt, but is with this patch applied.
This patch copies the technique used in GDB to transform the dep file
paths to the proper form.
Also, while testing using the depcomp method of dependency tracking (by
just hacking the condition), I noticed that depcomp was not found. The
path to depcomp seems to be missing a "..".
gdb/gdbserver/ChangeLog:
* Makefile.in (depcomp): Add "..".
(all_deps_files): New and use it.
|
|
For ports which use new target descriptions, remove
the xml files from being built into gdbserver.
gdbserver/
* configure.srv (aarch64*-*-linux*): Don't include xml.
(i[34567]86-*-cygwin*): Likewise.
(i[34567]86-*-linux*): Likewise.
(i[34567]86-*-lynxos*): Likewise.
(i[34567]86-*-mingw32ce*): Likewise.
(i[34567]86-*-mingw*): Likewise.
(i[34567]86-*-nto*): Likewise.
(tic6x-*-uclinux): Likewise.
(x86_64-*-linux*): Likewise.
(x86_64-*-mingw*): Likewise.
(x86_64-*-cygwin*): Likewise.
|
|
gdb/
* common/tdesc.h (tdesc_create_feature): Remove xml filename
parameter.
* features/aarch64-core.c (create_feature_aarch64_core):
Regenerate.
* features/aarch64-fpu.c (create_feature_aarch64_fpu):
Likewise.
* features/i386/32bit-avx.c (create_feature_i386_32bit_avx):
Likewise.
* features/i386/32bit-avx512.c
(create_feature_i386_32bit_avx512): Likewise.
* features/i386/32bit-core.c (create_feature_i386_32bit_core):
Likewise.
* features/i386/32bit-linux.c (create_feature_i386_32bit_linux):
Likewise.
* features/i386/32bit-mpx.c (create_feature_i386_32bit_mpx):
Likewise.
* features/i386/32bit-pkeys.c (create_feature_i386_32bit_pkeys):
Likewise.
* features/i386/32bit-sse.c (create_feature_i386_32bit_sse):
Likewise.
* features/i386/64bit-avx.c (create_feature_i386_64bit_avx):
Likewise.
* features/i386/64bit-avx512.c
(create_feature_i386_64bit_avx512): Likewise.
* features/i386/64bit-core.c (create_feature_i386_64bit_core):
Likewise.
* features/i386/64bit-linux.c (create_feature_i386_64bit_linux):
Likewise.
* features/i386/64bit-mpx.c (create_feature_i386_64bit_mpx):
Likewise.
* features/i386/64bit-pkeys.c (create_feature_i386_64bit_pkeys):
Likewise.
* features/i386/64bit-segments.c
(create_feature_i386_64bit_segments): Likewise.
* features/i386/64bit-sse.c (create_feature_i386_64bit_sse):
Likewise.
* features/i386/x32-core.c
(create_feature_i386_x32_core): Likewise.
* features/tic6x-c6xp.c (create_feature_tic6x_c6xp): Likewise.
* features/tic6x-core.c (create_feature_tic6x_core): Likewise.
* features/tic6x-gp.c (create_feature_tic6x_gp): Likewise.
* target-descriptions.c: In generated code, don't pass xml
filename.
gdbserver/
* tdesc.c: Remove xml parameter.
|
|
Add a print_xml_feature visitor class which turns a
target description into xml. Both gdb and gdbserver can do this.
gdb/
* common/tdesc.c (print_xml_feature::visit_pre): Add xml parsing.
(print_xml_feature::visit_post): Likewise.
(print_xml_feature::visit): Likewise.
* common/tdesc.h (tdesc_get_features_xml): Use const tdesc.
(print_xml_feature): Add new class.
* regformats/regdat.sh: Null xmltarget on feature targets.
* target-descriptions.c (struct target_desc): Add xmltarget.
(maintenance_check_tdesc_xml_convert): Add unittest function.
(tdesc_get_features_xml): Add function to get xml.
(maintenance_check_xml_descriptions): Test xml generation.
* xml-tdesc.c (string_read_description_xml): Add function.
* xml-tdesc.h (string_read_description_xml): Add declaration.
gdbserver/
* gdb/gdbserver/server.c (get_features_xml): Remove cast.
* tdesc.c (void target_desc::accept): Fill in function.
(tdesc_get_features_xml): Remove old xml creation.
(print_xml_feature::visit_pre): Add xml vistor.
* tdesc.h (struct target_desc): Make xmltarget mutable.
(tdesc_get_features_xml): Remove declaration.
|
|
gdb/
* common/tdesc.h (tdesc_architecture_name): Add new declaration.
(tdesc_osabi_name): Likewise.
* target-descriptions.c (tdesc_architecture_name): Add new function.
(tdesc_osabi_name): Likewise.
gdbserver/
* tdesc.c (tdesc_architecture_name): Add new function.
(tdesc_osabi_name): Likewise.
(tdesc_get_features_xml): Use new functions.
|
|
gdb/
* common/tdesc.c (tdesc_predefined_type): Move to here.
(tdesc_named_type): Likewise.
(tdesc_create_vector): Likewise.
(tdesc_create_struct): Likewise.
(tdesc_set_struct_size): Likewise.
(tdesc_create_union): Likewise.
(tdesc_create_flags): Likewise.
(tdesc_create_enum): Likewise.
(tdesc_add_field): Likewise.
(tdesc_add_typed_bitfield): Likewise.
(tdesc_add_bitfield): Likewise.
(tdesc_add_flag): Likewise.
(tdesc_add_enum_value): Likewise.
* common/tdesc.h (struct tdesc_type_builtin): Likewise.
(struct tdesc_type_vector): Likewise.
(struct tdesc_type_field): Likewise.
(struct tdesc_type_with_fields): Likewise.
(tdesc_create_enum): Add declaration.
(tdesc_add_typed_bitfield): Likewise.
(tdesc_add_enum_value): Likewise.
* target-descriptions.c (tdesc_type_field): Move from here.
(tdesc_type_builtin): Likewise.
(tdesc_type_vector): Likewise.
(tdesc_type_with_fields): Likewise.
(tdesc_predefined_types): Likewise.
(tdesc_named_type): Likewise.
(tdesc_create_vector): Likewise.
(tdesc_create_struct): Likewise.
(tdesc_set_struct_size): Likewise.
(tdesc_create_union): Likewise.
(tdesc_create_flags): Likewise.
(tdesc_create_enum): Likewise.
(tdesc_add_field): Likewise.
(tdesc_add_typed_bitfield): Likewise.
(tdesc_add_bitfield): Likewise.
(tdesc_add_flag): Likewise.
(tdesc_add_enum_value): Likewise.
* gdb/target-descriptions.h (tdesc_create_enum): Likewise.
(tdesc_add_typed_bitfield): Likewise.
(tdesc_add_enum_value): Likewise.
gdbserver/
* tdesc.c (tdesc_create_flags): Remove.
(tdesc_add_flag): Likewise.
(tdesc_named_type): Likewise.
(tdesc_create_union): Likewise.
(tdesc_create_struct): Likewise.
(tdesc_create_vector): Likewise.
(tdesc_add_bitfield): Likewise.
(tdesc_add_field): Likewise.
(tdesc_set_struct_size): Likewise.
|
|
gdb/
* common/tdesc.c (tdesc_feature::accept): Move to here.
(tdesc_feature::operator==): Likewise.
(tdesc_create_reg): Likewise.
* common/tdesc.h (tdesc_type_kind): Likewise.
(struct tdesc_type): Likewise.
(struct tdesc_feature): Likewise.
* regformats/regdat.sh: Create a feature.
* target-descriptions.c (tdesc_type_kind): Move from here.
(tdesc_type): Likewise.
(tdesc_type_up): Likewise.
(tdesc_feature): Likewise.
(tdesc_create_reg): Likewise.
gdbserver/
* tdesc.c (~target_desc): Remove implictly deleted items.
(init_target_desc): Iterate all features.
(tdesc_get_features_xml): Use vector.
(tdesc_create_feature): Create feature.
* tdesc.h (tdesc_feature) Remove
(target_desc): Add features.
|
|
gdb/
* Makefile.in: Add arch/tdesc.c
* common/tdesc.c: New file.
* common/tdesc.h (tdesc_element_visitor): Move to here.
(tdesc_element): Likewise.
(tdesc_reg): Likewise.
(tdesc_reg_up): Likewise.
* regformats/regdef.h (reg): Add offset to constructors.
* target-descriptions.c (tdesc_element_visitor): Move from here.
(tdesc_element): Likewise.
(tdesc_reg): Likewise.
(tdesc_reg_up): Likewise.
gdbserver/
* Makefile.in: Add common/tdesc.c
* tdesc.c (init_target_desc): init all reg_defs from register vector.
(tdesc_create_reg): Create tdesc_reg.
* tdesc.h (tdesc_feature): Add register vector.
|
|
This is a straightforward replacement, no change in behavior are
intended/expected.
gdb/gdbserver/ChangeLog:
* tdesc.h (struct target_desc) <features>: Change type to
std::vector<std::string>.
* tdesc.c (target_desc::~target_desc): Adjust to std::vector
changes.
(tdesc_get_features_xml): Likewise.
(tdesc_create_feature): Likewise.
|
|
gdb/
* regformats/regdef.h (reg): Add constructors.
gdb/gdbserver/
* regcache.c (find_register_by_number): Return a ref.
(find_regno): Use references.
(register_size): Likewise.
(register_data): Likewise.
* tdesc.c (target_desc::~target_desc): Remove free calls.
(target_desc::operator==): Use std::vector compare.
(init_target_desc): Use reference.
(tdesc_create_reg): Use reg constructors.
* tdesc.h (struct target_desc): Replace pointer with object.
|
|
gdbserver/
* regcache.c (find_register_by_number): Make static.
(find_regno): Use find_register_by_number
* regcache.h (struct reg): Remove declaration.
|
|
gdbserver/
* tdesc.c (target_desc::~target_desc): Move to here.
(target_desc::operator==): Likewise.
* tdesc.h (target_desc::~target_desc): Move from here.
(target_desc::operator==): Likewise.
|
|
This corrects bad formatting in the newly introduced function
s390_get_wordsize.
gdb/gdbserver/ChangeLog:
* linux-s390-low.c (s390_get_wordsize): Correct brace style.
|
|
The in-process agent does not handle tdescs with guarded storage yet.
This is fixed.
gdb/gdbserver/ChangeLog:
* linux-s390-ipa.c (get_ipa_tdesc): Add handling for
S390_TDESC_GS.
* linux-s390-low.c (s390_get_ipa_tdesc_idx): Likewise.
(initialize_low_tracepoint): Call init_registers_s390x_gs_linux64
and init_registers_s390_gs_linux64.
|
|
On S390, the guarded storage register set is only valid if guarded storage
is active. Reading/writing the register set yields errors if this is not
the case. Then gdbserver emits warnings like these:
Warning: ptrace(regsets_store_inferior_registers): No data available
Apart from confusing the user, this can also lead to test case failures
due to unexpected output. To suppress this, make the guarded storage
regsets read-only for now.
gdb/gdbserver/ChangeLog:
* linux-s390-low.c (s390_fill_gs): Remove function.
(s390_fill_gsbc): Remove function.
(s390_regsets): Set fill functions for the guarded storage regsets
to NULL.
|
|
On s390x, when running attach.exp with native-extended-gdbserver,
gdbserver crashes in find_regno like this:
.../regcache.c:252: A problem internal to GDBserver has been detected.
Unknown register tdb0 requested
On the GDB side it looks like this:
(gdb) attach 31568
Attaching to process 31568
Remote connection closed
The test case attempts to attach to a new process via the already running
gdbserver. Thus s390_arch_setup is called a second time, and that's where
the problem occurs. In order to determine the word width (32 or 64 bits),
s390_arch_setup reads the pswm register through the regcache. For that it
uses a temporary tdesc which is supposed to work for all s390 targets,
since the actual tdesc has not been determined yet. But in this second
round this doesn't work, because s390_regsets has been updated already and
now contains regsets not described by the temporary tdesc, such as the one
containing tdb0.
This is fixed by rearranging the logic in s390_arch_setup.
gdb/gdbserver/ChangeLog:
* linux-s390-low.c (s390_get_hwcap): Replace tdesc parameter by
the word size. Add comment.
(s390_get_wordsize): New function.
(s390_arch_setup): No longer select a temporary tdesc to fetch the
pswm with it. Instead, use s390_get_wordsize to determine the
word size first and derive the correct tdesc from that directly.
|
|
Many projects (e.g. the Linux kernel) and build systems use "silent"
rules, which means that they'll only print a summary of what's being
done instead of printing all the detailed command lines. While chatting
on the #gdb IRC channel, I realized a few people (including me) thought
it would be nice to have it in GDB too.
The idea is that too much text is not useful, the important information
gets lost. If there's only the essential information, it's more likely
to be useful. Most of the time, when I look at the build output, it's
to see how it's progressing. By just printing a brief summary of each
operation, I can easily spot what's currently being compiled and
therefore how the build progresses (with time you know the order in
which files are compiled almost by heart).
As with other projects (Linux, automake-based things, probably others),
it's possible to print the complete command lines by passing V=1 to make
(or any other non-zero value).
I had one hesitation about this: when people report build failures, we
are more likely to miss the full compile command line. We'll probably
sometimes need to ask people to include the build log with "make V=1".
I don't think it's a big downside, if other projects the size of the
Linux kernel can live with it, I'm sure we can too.
gdb/ChangeLog:
* silent-rules.mk: New.
* Makefile.in: Include silent-rules.mk
(srcdir, VPATH, top_srcdir): Move up.
(COMPILE): Add ECHO_CXX.
(test-cp-name-parser$(EXEEXT)): Add ECHO_CXXLD.
(init.c): Add ECHO_INIT_C.
(gdb$(EXEEXT)): Add SILENCE and ECHO_CXXLD.
(version.c): Add ECHO_GEN.
(printcmd.o): Add ECHO_CXX.
(target-float.o): Add ECHO_CXX.
(ada-exp.o): Add ECHO_CXX.
(stamp-xml): Add SILENCE and ECHO_GEN_XML_BUILTIN.
(insight$(EXEEXT)): Add ECHO_CXXLD.
* gnulib/configure.ac: Add AM_SILENT_RULES.
* gnulib/aclocal.m4: Re-generate.
* gnulib/configure: Re-generate.
* gnulib/import/Makefile.in: Re-generate.
gdb/gdbserver/ChangeLog:
* Makefile.in: Include silent-rules.mk.
(srcdir, abs_top_srcdir, abs_srcdir, VPATH): Move up.
(COMPILE): Add ECHO_CXX.
(gdbserver$(EXEEXT)): Add SILENCE and ECHO_CXXLD.
(gdbreplay$(EXEEXT)): Add SILENCE and ECHO_CXXLD.
($(IPA_LIB)): Add SILENCE and ECHO_CXXLD.
(version-generated.c): Add ECHO_GEN.
(stamp-xml): Add SILENCE and ECHO_GEN_XML_BUILTIN_GENERATED.
(IPAGENT_COMPILE): Add ECHO_CXX.
(%-generated.c): Add ECHO_REGDAT.
|
|
This changes the printf command's %s and %ls formats to special-case
NULL, and print "(null)" for these. This is PR cli/14977. This
behavior seems a bit friendlier; I was undecided on whether other
invalid pointers should be handled specially somehow, so for the time
being I've left those out.
gdb/ChangeLog
2018-03-14 Tom Tromey <tom@tromey.com>
PR cli/14977:
* printcmd.c (printf_c_string, printf_wide_c_string): Special case
for NULL.
gdb/gdbserver/ChangeLog
2018-03-14 Tom Tromey <tom@tromey.com>
PR cli/14977:
* ax.c (ax_printf): Special case for NULL.
gdb/testsuite/ChangeLog
2018-03-14 Tom Tromey <tom@tromey.com>
PR cli/14977:
* gdb.base/printcmds.exp (test_printf): Add printf test of %s with
a null pointer.
* gdb.base/wchar.exp: Likewise.
|
|
[This patch should go on top of "linux_qxfer_libraries_svr4: Use
std::string", I should have sent them together as a series.]
I noticed that linux_qxfer_libraries_svr4 used xml_escape_text, which
returns an std::string. That string is then copied into a larger
buffer. It would be more efficient if we had a version of
xml_escape_text which appended to an existing string instead of
returning a new one. This is what this patch does.
I manually verified that the output of linux_qxfer_libraries_svr4 didn't
change before/after the patch.
gdb/ChangeLog:
* common/xml-utils.c (xml_escape_text): Move code to...
(xml_escape_text_append): ... this new function.
* common/xml-utils.h (xml_escape_text_append): New declaration.
* unittests/xml-utils-selftests.c (test_xml_escape_text_append):
New function.
(_initialize_xml_utils): register test_xml_escape_text_append as
a selftest.
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_qxfer_libraries_svr4): Use
xml_escape_text_append.
|
|
Use std::string, removing some manual memory management.
gdb/gdbserver/ChangeLog:
* linux-low.c (linux_qxfer_libraries_svr4): Use std::string.
|
|
Unless I'm missing something very obvious, this xstrdup seems
unnecessary to me. We can pass "mode" directly to sprintf.
gdb/gdbserver/ChangeLog:
* server.c (handle_general_set): Remove unnecessary xstrdup.
|
|
This patch makes delim_string_to_char_ptr_vec and all related functions
use std::vector of gdb::unique_xmalloc_ptr. This allows getting rid of
make_cleanup_free_char_ptr_vec. Returning a vector of
unique_xmalloc_ptr instead of std::string allows to minimize the impacts
on the calling code. We can evaluate later whether we could/should
return a vector of std::strings instead.
gdb/ChangeLog:
* common/gdb_vecs.h (make_cleanup_free_char_ptr_vec): Remove.
(delim_string_to_char_ptr_vec): Return std::vector of
gdb::unique_xmalloc_ptr.
(dirnames_to_char_ptr_vec_append): Take std::vector of
gdb::unique_xmalloc_ptr.
(dirnames_to_char_ptr_vec): Return std::vector of
gdb::unique_xmalloc_ptr.
* common/gdb_vecs.c (delim_string_to_char_ptr_vec_append):
Take std::vector of gdb::unique_xmalloc_ptr, adjust the code.
(delim_string_to_char_ptr_vec): Return an std::vector of
gdb::unique_xmalloc_ptr, adjust the code.
(dirnames_to_char_ptr_vec_append): Take an std::vector of
gdb::unique_xmalloc_ptr, adjust the code.
(dirnames_to_char_ptr_vec): Return an std::vector of
gdb::unique_xmalloc_ptr, adjust the code.
* auto-load.c (auto_load_safe_path_vec): Change type to
std::vector of gdb::unique_xmalloc_ptr.
(auto_load_expand_dir_vars): Return an std::vector of
gdb::unique_xmalloc_ptr, adjust the code.
(auto_load_safe_path_vec_update): Adjust.
(filename_is_in_auto_load_safe_path_vec): Adjust.
(auto_load_objfile_script_1): Adjust.
* build-id.c (build_id_to_debug_bfd): Adjust.
* linux-thread-db.c (thread_db_load_search): Adjust.
* source.c (add_path): Adjust.
(openp): Adjust.
* symfile.c (find_separate_debug_file): Adjust.
* utils.c (do_free_char_ptr_vec): Remove.
(make_cleanup_free_char_ptr_vec): Remove.
gdb/gdbserver/ChangeLog:
* server.c (parse_debug_format_options): Adjust to
delim_string_to_char_ptr_vec changes.
* thread-db.c (thread_db_load_search): Adjust to
dirnames_to_char_ptr_vec changes.
|
|
By removing the supports_btrace gdbserver target method we relied on GDB
trying to enable branch tracing and failing on the attempt.
For targets that do not provide the btrace methods, however, an initial
request from GDB for the branch trace configuration to detect whether
gdbserver is already recording resulted in a protocol error.
Have the btrace target methods throw a "Target does not suppor branch
tracing" error and be prepared to handle exceptions in all functions that
call btrace target methods. We therefore turn the target_* macros into
static inline functions.
Also remove the additional btrace target method checks that resulted in
the above protocol error.
Thanks to Maciej W. Rozycki <macro@mips.com> for reporting this.
gdbserver/
* target.h (target_enable_btrace, target_disable_btrace)
(target_read_btrace, target_read_btrace_conf): Turn macro into
inline function. Throw error if target method is not defined.
* server.c (handle_qxfer_btrace, handle_qxfer_btrace_conf): Remove
check for btrace target method. Be prepared to handle exceptions
from btrace target methods.
|
|
I forgot to address Pedro's comment about my last patch and change the
order of the message printed when getcwd returns NULL on gdbserver.
This obvious commit does it.
gdb/gdbserver/ChangeLog:
2018-02-28 Sergio Durigan Junior <sergiodj@redhat.com>
* server.c (captured_main): Change order of error message printed
when the current working directory cannot be found.
|
|
Simon mentioned on IRC that, after the startup-with-shell feature has
been implemented on gdbserver, it is not possible to specify a
filename-only binary, like:
$ gdbserver :1234 a.out
/bin/bash: line 0: exec: a.out: not found
During startup program exited with code 127.
Exiting
This happens on systems where the current directory "." is not listed
in the PATH environment variable. Although including "." in the PATH
variable is a possible workaround, this can be considered a regression
because before startup-with-shell it was possible to use only the
filename (due to reason that gdbserver used "exec*" directly).
The idea of the patch is to verify if the program path provided by the
user (or by the remote protocol) contains a directory separator
character. If it doesn't, it means we're dealing with a filename-only
binary, so we call "gdb_abspath" to properly expand it and transform
it into a full path. Otherwise, we leave the program path untouched.
This mimicks the behaviour seen on GDB (look at "openp" and
"attach_inferior", for example).
I am also submitting a testcase which exercises the scenario described
above. This test requires gdbserver to be executed in a different CWD
than the original, so I also created a helper function, "with_cwd" (on
testsuite/lib/gdb.exp), which takes care of cd'ing into and out of the
specified dir.
Built and regtested on BuildBot, without regressions.
gdb/ChangeLog:
2018-02-28 Sergio Durigan Junior <sergiodj@redhat.com>
Simon Marchi <simon.marchi@polymtl.ca>
* common/common-utils.c: Include "sys/stat.h".
(is_regular_file): Move here from "source.c"; change return
type to "bool".
* common/common-utils.h (is_regular_file): New prototype.
* common/pathstuff.c (contains_dir_separator): New function.
* common/pathstuff.h (contains_dir_separator): New prototype.
* source.c: Don't include "sys/stat.h".
(is_regular_file): Move to "common/common-utils.c".
gdb/gdbserver/ChangeLog:
2018-02-28 Sergio Durigan Junior <sergiodj@redhat.com>
* server.c: Include "filenames.h" and "pathstuff.h".
(program_name): Delete variable.
(program_path): New anonymous class.
(get_exec_wrapper): Use "program_path" instead of
"program_name".
(handle_v_run): Likewise.
(captured_main): Likewise.
(process_serial_event): Likewise.
gdb/testsuite/ChangeLog:
2018-02-28 Sergio Durigan Junior <sergiodj@redhat.com>
* gdb.server/abspath.exp: New file.
* lib/gdb.exp (with_cwd): New procedure.
|
|
This commit moves the path manipulation routines found on utils.c to a
new common/pathstuff.c, and updates the Makefile.in's accordingly.
The routines moved are "gdb_realpath", "gdb_realpath_keepfile" and
"gdb_abspath".
This will be needed because gdbserver will have to call "gdb_abspath"
on my next patch, which implements a way to expand the path of the
inferior provided by the user in order to allow specifying just the
binary name when starting gdbserver, like:
$ gdbserver :1234 a.out
With the recent addition of the startup-with-shell feature on
gdbserver, this scenario doesn't work anymore if the user doesn't have
the current directory listed in the PATH variable.
I had to do a minor adjustment on "gdb_abspath" because we don't have
access to "tilde_expand" on gdbserver, so now the function is using
"gdb_tilde_expand" instead. Otherwise, the code is the same.
Regression tested on the BuildBot, without regressions.
gdb/ChangeLog:
2018-02-28 Sergio Durigan Junior <sergiodj@redhat.com>
* Makefile.in (COMMON_SFILES): Add "common/pathstuff.c".
(HFILES_NO_SRCDIR): Add "common/pathstuff.h".
* auto-load.c: Include "common/pathstuff.h".
* common/common-def.h (current_directory): Move here.
* common/gdb_tilde_expand.c (gdb_tilde_expand_up): New
function.
* common/gdb_tilde_expand.h (gdb_tilde_expand_up): New
prototype.
* common/pathstuff.c: New file.
* common/pathstuff.h: New file.
* compile/compile.c: Include "common/pathstuff.h".
* defs.h (current_directory): Move to "common/common-defs.h".
* dwarf2read.c: Include "common/pathstuff.h".
* exec.c: Likewise.
* guile/scm-safe-call.c: Likewise.
* linux-thread-db.c: Likewise.
* main.c: Likewise.
* nto-tdep.c: Likewise.
* objfiles.c: Likewise.
* source.c: Likewise.
* symtab.c: Likewise.
* utils.c: Include "common/pathstuff.h".
(gdb_realpath): Move to "common/pathstuff.c".
(gdb_realpath_keepfile): Likewise.
(gdb_abspath): Likewise.
* utils.h (gdb_realpath): Move to "common/pathstuff.h".
(gdb_realpath_keepfile): Likewise.
(gdb_abspath): Likewise.
gdb/gdbserver/ChangeLog:
2018-02-28 Sergio Durigan Junior <sergiodj@redhat.com>
* Makefile.in (SFILES): Add "$(srcdir)/common/pathstuff.c".
(OBJS): Add "pathstuff.o".
* server.c (current_directory): New global variable.
(captured_main): Initialize "current_directory".
|
|
gdb/
* arch/amd64.h: Use common/tdesc.h.
* arch/i386.c: Likewise.
* arch/i386.h: Likewise.
* arch/tic6x.c: Likewise.
* arch/tdesc.h: Move file from here...
* common/tdesc.h: ...to here.
* features/aarch64-core.c: Regenerate.
* features/aarch64-fpu.c: Regenerate.
* features/i386/32bit-avx.c: Regenerate.
* features/i386/32bit-avx512.c: Regenerate.
* features/i386/32bit-core.c: Regenerate.
* features/i386/32bit-linux.c: Regenerate.
* features/i386/32bit-mpx.c: Regenerate.
* features/i386/32bit-pkeys.c: Regenerate.
* features/i386/32bit-sse.c: Regenerate.
* features/i386/64bit-avx.c: Regenerate.
* features/i386/64bit-avx512.c: Regenerate.
* features/i386/64bit-core.c: Regenerate.
* features/i386/64bit-linux.c: Regenerate.
* features/i386/64bit-mpx.c: Regenerate.
* features/i386/64bit-pkeys.c: Regenerate.
* features/i386/64bit-segments.c: Regenerate.
* features/i386/64bit-sse.c: Regenerate.
* features/i386/x32-core.c: Regenerate.
* features/tic6x-c6xp.c: Regenerate.
* features/tic6x-core.c: Regenerate.
* features/tic6x-gp.c: Regenerate.
* target-descriptions.c: Use common/tdesc.h.
* target-descriptions.h: Likewise.
gdbserver/
* tdesc.c: Use common/tdesc.h.
* tdesc.h: Likewise.
|
|
gdbserver/
* Makefile.in: Switch order of make rules.
|
|
gdb/
* Makefile.in: (COMMON_SFILES): Add common/*.c files.
(SFILES): Remove common/*.c files.
(COMMON_OBS): Remove some *.o files built from common/*.c files.
* common/common.host: Add common reference.
* configure.ac: Likewise.
* configure: Regenerate.
gdbserver/
* Makefile.in: Add common directory in build.
* configure.ac: Add common reference.
* configure: Regenerate.
|
|
Remove the to_supports_btrace target method and instead rely on detecting errors
when trying to enable recording. This will also provide a suitable error
message explaining why recording is not possible.
For remote debugging, gdbserver will now always advertise branch tracing related
packets. When talking to an older GDB, this will cause GDB to try to enable
branch tracing and gdbserver to report a suitable error message every time.
An older gdbserver will not advertise branch tracing related packets if the
one-time check failed, so a newer GDB with this patch will fail to enable branch
tracing at remote_enable_btrace() rather than at btrace_enable(). The error
message is the same in both cases so there should be no user-visible change.
gdb/
* btrace.c (btrace_enable): Remove target_supports_btrace call.
* nat/linux-btrace.c (perf_event_pt_event_type): Move.
(kernel_supports_bts, kernel_supports_pt, linux_supports_bts)
(linux_supports_pt, linux_supports_btrace): Remove.
(linux_enable_bts): Call cpu_supports_bts.
* nat/linux-btrace.h (linux_supports_btrace): Remove.
* remote.c (remote_supports_btrace): Remove.
(init_remote_ops): Remove remote_supports_btrace.
* target-delegates.c: Regenerated.
* target.c (target_supports_btrace): Remove.
* target.h (target_ops) <to_supports_btrace>: Remove
(target_supports_btrace): Remove.
* x86-linux-nat.c (x86_linux_create_target): Remove
linux_supports_btrace.
gdbserver/
* linux-low.c (linux_target_ops): Remove linux_supports_btrace.
* nto-low.c (nto_target_ops): Remove NULL for supports_btrace.
* spu-low.c (spu_target_ops): Likewise.
* win32-low.c (win32_target_ops): Likewise.
* server.c (supported_btrace_packets): Report packets unconditionally.
* target.h (target_ops) <supports_btrace>: Remove.
(target_supports_btrace): Remove.
|
|
Change error reporting to use exceptions and be prepared to catch them in
gdbserver. We use the exception message in our error reply to GDB.
This may remove some detail from the error message in the native case since
errno is no longer printed. Later patches will improve that.
We're still using error strings on the RSP level. This patch does not affect
the interoperability of older/newer GDB/gdbserver.
gdbserver/
* server.c (handle_btrace_enable_bts, handle_btrace_enable_pt)
(handle_btrace_disable): Change return type to void. Use exceptions
to report errors.
(handle_btrace_general_set): Catch exception and copy message to
return message.
gdb/
* nat/linux-btrace.c (linux_enable_btrace): Throw exception if enabling
btrace failed.
* x86-linux-nat.c (x86_linux_enable_btrace): Catch btrace enabling
exception and use message in own exception.
|
|
This removes make_cleanup_restore_current_thread from gdbserver,
replacing it with a use of scoped_restore.
2018-02-08 Tom Tromey <tom@tromey.com>
* linux-low.c (install_software_single_step_breakpoints): Use
make_scoped_restore.
* inferiors.c (make_cleanup_restore_current_thread): Remove.
(do_restore_current_thread_cleanup): Remove.
* gdbthread.h (make_cleanup_restore_current_thread): Don't
declare.
|
