diff options
Diffstat (limited to 'gdb/doc/gdb.texinfo')
| -rw-r--r-- | gdb/doc/gdb.texinfo | 123 |
1 files changed, 0 insertions, 123 deletions
diff --git a/gdb/doc/gdb.texinfo b/gdb/doc/gdb.texinfo index 58c254d..b3dd7a7 100644 --- a/gdb/doc/gdb.texinfo +++ b/gdb/doc/gdb.texinfo @@ -11414,7 +11414,6 @@ configurations. * ARM:: ARM * H8/300:: Hitachi H8/300 * H8/500:: Hitachi H8/500 -* i960:: Intel i960 * M32R/D:: Mitsubishi M32R/D * M68K:: Motorola M68K * MIPS Embedded:: MIPS Embedded @@ -11668,128 +11667,6 @@ memory}. The accepted values for @var{mod} are @code{small}, @end table -@node i960 -@subsection Intel i960 - -@table @code - -@kindex target mon960 -@item target mon960 @var{dev} -MON960 monitor for Intel i960. - -@kindex target nindy -@item target nindy @var{devicename} -An Intel 960 board controlled by a Nindy Monitor. @var{devicename} is -the name of the serial device to use for the connection, e.g. -@file{/dev/ttya}. - -@end table - -@cindex Nindy -@cindex i960 -@dfn{Nindy} is a ROM Monitor program for Intel 960 target systems. When -@value{GDBN} is configured to control a remote Intel 960 using Nindy, you can -tell @value{GDBN} how to connect to the 960 in several ways: - -@itemize @bullet -@item -Through command line options specifying serial port, version of the -Nindy protocol, and communications speed; - -@item -By responding to a prompt on startup; - -@item -By using the @code{target} command at any point during your @value{GDBN} -session. @xref{Target Commands, ,Commands for managing targets}. - -@end itemize - -@cindex download to Nindy-960 -With the Nindy interface to an Intel 960 board, @code{load} -downloads @var{filename} to the 960 as well as adding its symbols in -@value{GDBN}. - -@menu -* Nindy Startup:: Startup with Nindy -* Nindy Options:: Options for Nindy -* Nindy Reset:: Nindy reset command -@end menu - -@node Nindy Startup -@subsubsection Startup with Nindy - -If you simply start @code{@value{GDBP}} without using any command-line -options, you are prompted for what serial port to use, @emph{before} you -reach the ordinary @value{GDBN} prompt: - -@smallexample -Attach /dev/ttyNN -- specify NN, or "quit" to quit: -@end smallexample - -@noindent -Respond to the prompt with whatever suffix (after @samp{/dev/tty}) -identifies the serial port you want to use. You can, if you choose, -simply start up with no Nindy connection by responding to the prompt -with an empty line. If you do this and later wish to attach to Nindy, -use @code{target} (@pxref{Target Commands, ,Commands for managing targets}). - -@node Nindy Options -@subsubsection Options for Nindy - -These are the startup options for beginning your @value{GDBN} session with a -Nindy-960 board attached: - -@table @code -@item -r @var{port} -Specify the serial port name of a serial interface to be used to connect -to the target system. This option is only available when @value{GDBN} is -configured for the Intel 960 target architecture. You may specify -@var{port} as any of: a full pathname (e.g. @samp{-r /dev/ttya}), a -device name in @file{/dev} (e.g. @samp{-r ttya}), or simply the unique -suffix for a specific @code{tty} (e.g. @samp{-r a}). - -@item -O -(An uppercase letter ``O'', not a zero.) Specify that @value{GDBN} should use -the ``old'' Nindy monitor protocol to connect to the target system. -This option is only available when @value{GDBN} is configured for the Intel 960 -target architecture. - -@quotation -@emph{Warning:} if you specify @samp{-O}, but are actually trying to -connect to a target system that expects the newer protocol, the connection -fails, appearing to be a speed mismatch. @value{GDBN} repeatedly -attempts to reconnect at several different line speeds. You can abort -this process with an interrupt. -@end quotation - -@item -brk -Specify that @value{GDBN} should first send a @code{BREAK} signal to the target -system, in an attempt to reset it, before connecting to a Nindy target. - -@quotation -@emph{Warning:} Many target systems do not have the hardware that this -requires; it only works with a few boards. -@end quotation -@end table - -The standard @samp{-b} option controls the line speed used on the serial -port. - -@c @group -@node Nindy Reset -@subsubsection Nindy reset command - -@table @code -@item reset -@kindex reset -For a Nindy target, this command sends a ``break'' to the remote target -system; this is only useful if the target has been equipped with a -circuit to perform a hard reset (or some other interesting action) when -a break is detected. -@end table -@c @end group - @node M32R/D @subsection Mitsubishi M32R/D |