* configure.in: Add nlm subdir to configdirs for alpha-*-netware

	target.
	* defs.h (enum language):  Add language_asm.
	* findvar.c (read_register_bytes read_register_gen
	write_register_bytes read_register read_register_pid
	write_register write_register_pid supply_register):  Move multi-
	thread handling down into these routines.  Create XXX_pid routines
	that allow register references to specify the pid.
	* findvar.c infcmd.c (read_pc read_pc_pid write_pc write_pc_pid
	read_sp write_sp read_fp write_fp):  Move these routines from
	infcmd to findvar to centralize the whole mess.
	* i386-nlmstub.c:  Portability fixes.
	* infptrace.c (child_resume):  Conditionalize to allow other natives
	to override it.  Remove PIDGET gubbish, it's no longer necessary.
	* infrun.c (wait_for_inferior):  Put registers_changed() before
	target_wait() to speed up remote debugging.
	* Replace code that reads registers from other threads with much
	nicer looking new function calls (see changes to findvar.c).
	* Don't skip prologues if debugging assembly source.
	* lynx-nat.c (child_resume):  Lynx now needs it's own version of
	child_resume to handle multi-thread debugging properly.
	* remote.c:  Add O response to get console output from target.
	* (readchar): Add timeout parameter.  Handle SERIAL_EOF and
	SERIAL_ERROR here to simplify callers.
	* Change static var timeout to remote_timeout.
	* (fromhex):  Remove unnecessary return -1 at end of routine.
	* (remote_wait):  Turn this into a big switch statement.  Add
	support for O response.
	* (putpkt):  Remove unnecessary handling of SERIAL_EOF/ERROR.
	* (getpkt):  Split getpkt into two parts.  read_frame deals with
	all formatting issues, run-length encoding, and framing.  getpkt
	now handles error recovery, and frame detection.
	* ser-tcp.c (tcp_readchar):  Handle EINTR from read().
	* ser-unix.c (hardwire_raw):  Set CLOCAL so that we ignore modem
	control.  (hardwire_readchar):  Handle EINTR from read().
	* symfile.c (deduce_language_from_filename):  Add support for .s
	files.
	* config/nm-lynx.h:  Define CHILD_WAIT so that lynx-nat.c can
	override infptrace's child_wait.
	* config/rs6000/rs6000lynx.mh:  Use xm-rs6000ly.h & nm-rs6000ly.h
	instead of XXXlynx.h.
	* config/rs6000/rs6000lynx.mt:  Use tm-rs6000ly.h instead of
	tm-rs6000lynx.h.
	* nlm/gdbserve.c:  Portability fixes.

1 files changed, 38 insertions, 0 deletions

diff --git a/gdb/lynx-nat.c b/gdb/lynx-nat.c
index 451b4f5..49f361d 100644
--- a/gdb/lynx-nat.c
+++ b/gdb/lynx-nat.c
@@ -652,6 +652,44 @@ child_wait (pid, ourstatus)
     }
 }
 
+/* Resume execution of the inferior process.
+   If STEP is nonzero, single-step it.
+   If SIGNAL is nonzero, give it that signal.  */
+
+void
+child_resume (pid, step, signal)
+     int pid;
+     int step;
+     enum target_signal signal;
+{
+  errno = 0;
+
+  if (pid == -1)
+    /* Resume all threads.  */
+    /* I think this only gets used in the non-threaded case, where "resume
+       all threads" and "resume inferior_pid" are the same.  */
+    pid = inferior_pid;
+
+  /* An address of (PTRACE_ARG3_TYPE)1 tells ptrace to continue from where
+     it was.  (If GDB wanted it to start some other way, we have already
+     written a new PC value to the child.)
+
+     If this system does not support PT_STEP, a higher level function will
+     have called single_step() to transmute the step request into a
+     continue request (by setting breakpoints on all possible successor
+     instructions), so we don't have to worry about that here.  */
+
+  if (step)
+    ptrace (PTRACE_SINGLESTEP_ONE,     pid, (PTRACE_ARG3_TYPE) 1,
+	    target_signal_to_host (signal));
+  else
+    ptrace (PTRACE_CONT_ONE, pid, (PTRACE_ARG3_TYPE) 1,
+	    target_signal_to_host (signal));
+
+  if (errno)
+    perror_with_name ("ptrace");
+}
+
 /* Convert a Lynx process ID to a string.  Returns the string in a static
    buffer.  */