aboutsummaryrefslogtreecommitdiff
path: root/binutils/testsuite
AgeCommit message (Collapse)AuthorFilesLines
2022-09-14Binutils: Readelf testcase failing with clangRupesh Potharla1-3/+4
* testsuite/binutils-all/readelf.exp (readelf_wi_test): Extend regexps to allow for output genreated by the Clang compiler.
2022-08-13readelf: print 0x0 as 0, and remove trailing spacesAlan Modra21-197/+197
This changes readelf output a little, removing the 0x prefix on hex output when the value is 0, except in cases where a fixed field width is shown. %#010x is not a good replacement for 0x%08x.
2022-08-10bfd: Add support for LoongArch64 EFI (efi-*-loongarch64).Youling Tang3-0/+78
This adds support for efi-loongarch64 by virtue of adding a new PEI target pei-loongarch64. This is not a full target and only exists to support EFI at this time. This means that this target does not support relocation processing and is mostly a container format. This format has been added to elf based loongarch64 targets such that efi images can be made natively on Linux. However this target is not valid for use with gas but only with objcopy. We should't limit addresses to 32-bits for 64-bit vma, otherwise there will be "RVA truncated" error when using objcopy on loongarch64. With these changes the resulting file is recognized as an efi image. Any magic number is based on the Microsoft PE specification [1]. The test results are as follows: $ make check-binutils RUNTESTFLAGS='loongarch64.exp' PASS: Check if efi app format is recognized $ objdump -h -f tmpdir/loongarch64copy.o tmpdir/loongarch64copy.o: file format pei-loongarch64 architecture: Loongarch64, flags 0x00000132: EXEC_P, HAS_SYMS, HAS_LOCALS, D_PAGED start address 0x0000000000000000 Sections: Idx Name Size VMA LMA File off Algn 0 .text 0000003c 00000000200000b0 00000000200000b0 00000200 2**2 CONTENTS, ALLOC, LOAD, READONLY, CODE [1] https://docs.microsoft.com/en-us/windows/win32/debug/pe-format bfd: * .gitignore (pe-loongarch64igen.c): New. * Makefile.am (pei-loongarch64.lo, pe-loongarch64igen.lo, pei-loongarch64.c, pe-loongarch64igen.c): Add support. * Makefile.in: Likewise. * bfd.c (bfd_get_sign_extend_vma): Add pei-loongarch64. * coff-loongarch64.c: New file. * coffcode.h (coff_set_arch_mach_hook, coff_set_flags, coff_write_object_contents) Add loongarch64 (loongarch64_pei_vec) support. * config.bfd: Likewise. * configure: Likewise. * configure.ac: Likewise. * libpei.h (GET_OPTHDR_IMAGE_BASE, PUT_OPTHDR_IMAGE_BASE, GET_OPTHDR_SIZE_OF_STACK_RESERVE, PUT_OPTHDR_SIZE_OF_STACK_RESERVE, GET_OPTHDR_SIZE_OF_STACK_COMMIT, PUT_OPTHDR_SIZE_OF_STACK_COMMIT, GET_OPTHDR_SIZE_OF_HEAP_RESERVE, PUT_OPTHDR_SIZE_OF_HEAP_RESERVE, GET_OPTHDR_SIZE_OF_HEAP_COMMIT, PUT_OPTHDR_SIZE_OF_HEAP_COMMIT, GET_PDATA_ENTRY, _bfd_peLoongArch64_bfd_copy_private_bfd_data_common, _bfd_peLoongArch64_bfd_copy_private_section_data, _bfd_peLoongArch64_get_symbol_info, _bfd_peLoongArch64_only_swap_filehdr_out, _bfd_peLoongArch64_print_private_bfd_data_common, _bfd_peLoongArch64i_final_link_postscript, _bfd_peLoongArch64i_only_swap_filehdr_out, _bfd_peLoongArch64i_swap_aouthdr_in, _bfd_peLoongArch64i_swap_aouthdr_out, _bfd_peLoongArch64i_swap_aux_in, _bfd_peLoongArch64i_swap_aux_out, _bfd_peLoongArch64i_swap_lineno_in, _bfd_peLoongArch64i_swap_lineno_out, _bfd_peLoongArch64i_swap_scnhdr_out, _bfd_peLoongArch64i_swap_sym_in, _bfd_peLoongArch64i_swap_sym_out, _bfd_peLoongArch64i_swap_debugdir_in, _bfd_peLoongArch64i_swap_debugdir_out, _bfd_peLoongArch64i_write_codeview_record, _bfd_peLoongArch64i_slurp_codeview_record, _bfd_peLoongArch64_print_ce_compressed_pdata): New. * peXXigen.c (_bfd_XXi_swap_aouthdr_in, _bfd_XXi_swap_aouthdr_out, _bfd_XXi_swap_scnhdr_out, pe_print_pdata, _bfd_XX_print_private_bfd_data_common, _bfd_XX_bfd_copy_private_section_data, _bfd_XXi_final_link_postscript): Support COFF_WITH_peLoongArch64, * pei-loongarch64.c: New file. * peicode.h (coff_swap_scnhdr_in, pe_ILF_build_a_bfd, pe_ILF_object_p): Support COFF_WITH_peLoongArch64. (jtab): Add dummy entry that traps. * targets.c (loongarch64_pei_vec): New. binutils * testsuite/binutils-all/loongarch64/loongarch64.exp: New file. * testsuite/binutils-all/loongarch64/pei-loongarch64.d: New test. * testsuite/binutils-all/loongarch64/pei-loongarch64.s: New test. include * coff/loongarch64.h: New file. * coff/pe.h (IMAGE_FILE_MACHINE_LOONGARCH64): New. Signed-off-by: Youling Tang <tangyouling@loongson.cn>
2022-08-09Default to enabling colored disassembly if output is to a terminal.Nick Clifton2-2/+2
PR 29457 * objdump.c (disassembler_color): Change type to an enum. (disassembler_extended_color): Remove. (usage): Update. (objdump_color_for_assembler_style): Update. (main): Update initialisation of disassembler_color. If not initialised via a command line option, set based upon terminal output. * doc/binutils.texi: Update description of disassmbler-color option. * testsuite/binutils-all/arc/objdump.exp: Add --disassembler-color=off option when disassembling. * testsuite/binutils-all/arm/objdump.exp: Likewise.
2022-07-22PR15951, binutils testsuite builds status wrapper unconditionallyAlan Modra1-1/+6
PR 15951 * testsuite/binutils-all/objcopy.exp: Build testglue.o when needs_status_wrapper.
2022-06-30Fix implementation of readelf's -wE and -wN options,Nick Clifton1-2/+2
* dwarf.c (dwarf_select_sections_by_name): If the entry's value is zero then clear the corresponding variable. (dwarf_select_sections_by_letters): Likewise. * testsuite/binutils-all/debuginfo.exp: Expect -WE and -wE debuginfod tests to fail.
2022-06-28Fix the display of the idnex values for DW_FORM_loclistx and ↵Nick Clifton1-41/+41
DW_FORM_rnglistx. Correct the display of .debug.loclists sections. PR 29267 * dwarf.c (display_debug_rnglists): New function, broken out of.. (display_debug_ranges): ... here. (read_and_display_attr_value): Correct calculation of index displayed for DW_FORM_loclistx and DW_FORM_rnglistx. * testsuite/binutils-all/x86-64/pr26808.dump: Update expected output.
2022-06-27Stop bogus warnings about DWARF indexed string offsets being too big.Nick Clifton1-3/+3
* dwarf.c (fetch_indexed_string): Do not use length of first table in string section as the length of every table in the section. * testsuite/binutils-all/pr26112.r: Update expected output.
2022-05-26Re: Add bionutils support for DWARF v5's DW_OP_addrxNatarajan, Kavitha2-0/+169
Testsuite files belonging to commit 3ac9da49378c.
2022-05-25Add bionutils support for DWARF v5's DW_OP_addrx.Natarajan, Kavitha2-2/+63
2022-05-20Stop readekf and objdump from aggressively following links.Nick Clifton3-6/+8
* dwarf.c (dwarf_select_sections_by_names): Return zero if no sections were selected. (dwarf_select_sections_by_letters): Likewise. * dwarf.h: (dwarf_select_sections_by_names): Update prototype. (dwarf_select_sections_by_letters): Update prototype. * objdump.c (might_need_separate_debug_info): New function. (dump_bfd): Call new function before attempting to load separate debug info files. (main): Do not enable dwarf section dumping for -WK or -WN. * readelf.c (parse_args): Do not enable dwarf section dumping for -wK or -wN. (might_need_separate_debug_info): New function. (process_object): Call new function before attempting to load separate debug info files. * testsuite/binutils-all/debuginfo.exp: Expect -WE and -wE debuginfod tests to pass. * testsuite/binutils-all/objdump.Wk: Add extra regexps. * testsuite/binutils-all/readelf.k: Add extra regexps.
2022-05-18Add a --no-weak option to nm.Nick Clifton2-1/+44
PR 29135 * nm.c (non_weak): New variable. (filter_symbols): When non-weak is true, ignore weak symbols. (long_options): Add --no-weak. (usage): Mention --no-weak. (main): Handle -W/--no-weak. * doc/binutils.texi: Document new feature. * NEWS: Mention the new feature. * testsuite/binutils-all/nm.exp: Add test of new feature. * testsuite/binutils-all/no-weak.s: New test source file.
2022-05-03Add a linker warning when creating potentially dangerous executable ↵Nick Clifton1-0/+2
segments. Add tests, options to disabke and configure switches to choose defaults.
2022-04-25Emit a note warning the user that creating an executable stack because of a ↵Nick Clifton1-0/+1
missing .note.GNU-stack section is deprecated. PR 29072 bfd * elflink.c (bfd_elf_size_dynamic_sections): Display a note to the user that the current ehaviour of creating an executable stack because of a missing .note.GNU-stack section is deprecated and will be changed in a future release. binutils* testsuite/lib/binutils-common.exp (prune_warnings_extra): Filter out notes about the executable stacjk behaviour beign deprecated. ld * testsuite/ld-elf/pr29072.b.warn: Update to include the note about the linker's behaviour being depreccated.
2022-04-21prune .note.GNU-stack warning from testsuiteAlan Modra1-2/+3
binutils/ * testsuite/lib/binutils-common.exp (prune_warnings_extra): Remove .note.GNU-stack warning. (run_dump_test): Call prune_warnings for ld and objcopy output. ld/ * testsuite/ld-elf/elf.exp: Disable prune_warnings_extra temporarily around test for absent .note.GNU-stack * testsuite/ld-cris/globsymw2.s, * testsuite/ld-cris/warn3.d: Modify "is not implemented" message to avoid dejagnu prune_warnings.
2022-04-06Add code to display the contents of .debug_loclists sections which contain ↵Nick Clifton2-42/+42
offset entry tables. PR 28981 * dwarf.c (fetch_indexed_value): Rename to fecth_indexed_addr and return the address, rather than a string. (fetch_indexed_value): New function - returns a value indexed by a DW_FORM_loclistx or DW_FORM_rnglistx form. (read_and_display_attr_value): Add support for DW_FORM_loclistx and DW_FORM_rnglistx. (process_debug_info): Load the loclists and rnglists sections. (display_loclists_list): Add support for DW_LLE_base_addressx, DW_LLE_startx_endx, DW_LLE_startx_length and DW_LLE_default_location. (display_offset_entry_loclists): New function. Displays a .debug_loclists section that contains offset entry tables. (display_debug_loc): Call the new function. (display_debug_rnglists_list): Add support for DW_RLE_base_addressx, DW_RLE_startx_endx and DW_RLE_startx_length. (display_debug_ranges): Display the contents of the section's header. * dwarf.h (struct debug_info): Add loclists_base field. * testsuite/binutils-all/dw5.W: Update expected output. * testsuite/binutils-all/x86-64/pr26808.dump: Likewise.
2022-03-16objcopy --weaken-symbol: apply to STB_GNU_UNIQUE symbolsFangrui Song2-0/+12
PR binutils/28926 * objcopy.c (filter_symbols): Apply weaken to STB_GNU_UNIQUE symbols * NEWS: Mention feature. * testsuite/binutils-all/objcopy.exp (objcopy_test_symbol_manipulation): New test. * testsuite/binutils-all/weaken-gnu-unique.s: New.
2022-03-10Add option to objdump/readelf to disable access to debuginfod servers.Nick Clifton1-1/+13
* dwarf.c (use_debuginfod): New variable. Set to 1. (load_separate_debug_info): Only call debuginfod_fetch_separate_debug_info is use_debuginfod is true. (dwarf_select_sections_by_names): Add do-not-use-debuginfod and use-debuginfod options. (dwarf_select_sections_by_letters): Add D and E options. * dwarf.h (use_debuginfod): New extern. * objdump.c (usage): Mention the new options. * readelf.c (usage): Likewise. * doc/binutils.texi: Document the new options. * doc/debug-options.texi: Describe the new options. * NEWS: Mention the new feature. * testsuite/binutils-all/debuginfod.exp: Add tests of the new options.
2022-03-06MIPS/opcodes: Fix alias annotation for branch instructionsMaciej W. Rozycki11-0/+181
Correct issues with INSN2_ALIAS annotation for branch instructions: - regular MIPS BEQZ/L and BNEZ/L assembly instructions are idioms for BEQ/L and BNE/L respectively with the `rs' operand equal to $0, - microMIPS 32-bit BEQZ and BNEZ assembly instructions are idioms for BEQ and BNE respectively with the `rt' operand equal to $0, - regular MIPS BAL assembly instruction is an idiom for architecture levels of up to the MIPSr5 ISA and a machine instruction on its own from the MIPSr6 ISA up. Add missing annotation to BEQZ/L and BNEZ/L accordingly then and add a new entry for BAL for the MIPSr6 ISA, correcting a disassembly bug: $ mips-linux-gnu-objdump -m mips:isa64r6 -M no-aliases -d bal.o bal.o: file format elf32-tradlittlemips Disassembly of section .text: 00000000 <foo>: 0: 04110000 0x4110000 ... $ Add test cases accordingly. Parts for regular MIPS BEQZ/L and BNEZ/L instructions from Sagar Patel. 2022-03-06 Maciej W. Rozycki <macro@orcam.me.uk> binutils/ * testsuite/binutils-all/mips/mips1-branch-alias.d: New test. * testsuite/binutils-all/mips/mips1-branch-noalias.d: New test. * testsuite/binutils-all/mips/mips2-branch-alias.d: New test. * testsuite/binutils-all/mips/mips2-branch-noalias.d: New test. * testsuite/binutils-all/mips/mips32r6-branch-alias.d: New test. * testsuite/binutils-all/mips/mips32r6-branch-noalias.d: New test. * testsuite/binutils-all/mips/micromips-branch-alias.d: New test. * testsuite/binutils-all/mips/micromips-branch-noalias.d: New test. * testsuite/binutils-all/mips/mips-branch-alias.s: New test source. * testsuite/binutils-all/mips/micromips-branch-alias.s: New test source. * testsuite/binutils-all/mips/mips.exp: Run the new tests. 2022-03-06 Sagar Patel <sagarmp@cs.unc.edu> Maciej W. Rozycki <macro@orcam.me.uk> opcodes/ * mips-opc.c (mips_builtin_opcodes): Fix INSN2_ALIAS annotation for "bal", "beqz", "beqzl", "bnez" and "bnezl" instructions. * micromips-opc.c (micromips_opcodes): Likewise for "beqz" and "bnez" instructions.
2022-02-09Test --only-keep-debug on ELF relocatablesPeilin Ye1-0/+57
Add a test for commit 7c4643efe7be, which fixed --only-keep-debug for ELF relocatables. * testsuite/binutils-all/objcopy.exp (keep_debug_symbols_for_elf_relocatable): New test.
2022-02-05Enable "size" as a dumpprog in ldAlan Modra1-0/+1
binutils/ * testsuite/lib/binutils-common.exp (run_dump_test): Reference global SIZE and SIZEFLAGS. ld/ * testsuite/config/default.exp: Define SIZE and SIZEFLAGS.
2022-01-18PowerPC64 DT_RELRAlan Modra1-1/+3
PowerPC64 takes a more traditional approach to DT_RELR than x86. Count relative relocs in check_relocs, allocate space for them and output in the usual places but not doing so when enable_dt_relr. DT_RELR is sized in the existing ppc stub relaxation machinery, run via the linker's ldemul_after_allocation hook. DT_RELR is output in the same function that writes ppc stubs, run via ldemul_finish. This support should be considered experimental. bfd/ * elf64-ppc.c (struct ppc_local_dyn_relocs): Renamed from ppc_dyn_relocs. Add rel_count field. Update uses. (struct ppc_dyn_relocs): New. Replace all uses of elf_dyn_relocs. (struct ppc_link_hash_table): Add relr_alloc, relr_count and relr_addr. (ppc64_elf_copy_indirect_symbol): Merge rel_count. (ppc64_elf_check_relocs): Init rel_count for global and local syms. (dec_dynrel_count): Change r_info param to reloc pointer. Update all callers. Handle decrementing rel_count. (allocate_got): Don't allocate space for relative relocs when enable_dt_relr. (allocate_dynrelocs): Likewise. (ppc64_elf_size_dynamic_sections): Likewise. Handle srelrdyn. (ppc_build_one_stub): Don't emit relative relocs on .branch_lt. (compare_relr_address, append_relr_off): New functions. (got_and_plt_relr_for_local_syms, got_and_plt_relr): Likewise. (ppc64_elf_size_stubs): Size .relr.syn. (ppc64_elf_build_stubs): Emit .relr.dyn. (build_global_entry_stubs_and_plt): Don't output relative relocs when enable_dt_relr. (write_plt_relocs_for_local_syms): Likewise. (ppc64_elf_relocate_section): Likewise. binutils/ * testsuite/lib/binutils-common.exp (supports_dt_relr): Add powerpc64. ld/ * emulparams/elf64ppc.sh: Source dt-relr.sh. * testsuite/ld-elf/dt-relr-2b.d: Adjust for powerpc. * testsuite/ld-elf/dt-relr-2c.d: Likewise. * testsuite/ld-elf/dt-relr-2d.d: Likewise. * testsuite/ld-elf/dt-relr-2e.d: Likewise.
2022-01-13testsuite supports_dt_relrAlan Modra1-0/+10
Tidy, and fix "FAIL: Build dt-relr-glibc-1b.so" on all non-x86 linux targets. binutils/ * binutils-common.exp (supports_dt_relr): New proc. ld/ * testsuite/config/default.exp (DT_RELR_LDFLAGS, NO_DT_RELR_LDFLAGS), (DT_RELR_CC_LDFLAGS, NO_DT_RELR_CC_LDFLAGS): Use supports_dt_relr. * testsuite/ld-elf/dt-relr.exp: Don't run unless supports_dt_relr. * testsuite/ld-elf/dt-relr-1a.d: Likewise. * testsuite/ld-elf/dt-relr-1b.d: Likewise. * testsuite/ld-elf/dt-relr-1c.d: Likewise. * testsuite/ld-elf/dt-relr-2a.d: Likewise. * testsuite/ld-elf/dt-relr-2b.d: Likewise. * testsuite/ld-elf/dt-relr-2c.d: Likewise. * testsuite/ld-elf/dt-relr-2d.d: Likewise. * testsuite/ld-elf/dt-relr-2e.d: Likewise. * testsuite/ld-elf/dt-relr-2f.d: Likewise. * testsuite/ld-elf/dt-relr-2g.d: Likewise. * testsuite/ld-elf/dt-relr-2h.d: Likewise. * testsuite/ld-elf/dt-relr-3a.d: Likewise. * testsuite/ld-elf/dt-relr-3b.d: Likewise.
2022-01-12elf: Support DT_RELR in linker testsH.J. Lu1-0/+1
Allow eabling and disabling DT_RELR in linker tests. Disable DT_RELR in linker tests which don't expect DT_RELR in linker outputs. binutils/ * testsuite/lib/binutils-common.exp (run_dump_test): Make DT_RELR_LDFLAGS and NO_DT_RELR_LDFLAGS global. ld/ * testsuite/config/default.exp (DT_RELR_LDFLAGS): New. (DT_RELR_CC_LDFLAGS): Likewise. (NO_DT_RELR_LDFLAGS): Likewise. (NO_DT_RELR_CC_LDFLAGS): Likewise. * testsuite/ld-elf/shared.exp: Pass $NO_DT_RELR_LDFLAGS to linker for some tests. * testsuite/ld-i386/export-class.exp: Likewise. * testsuite/ld-i386/i386.exp: Likewise. * testsuite/ld-i386/ibt-plt-2a.d: Pass $NO_DT_RELR_LDFLAGS to linker. * testsuite/ld-i386/ibt-plt-3a.d: Likewise. * testsuite/ld-i386/ibt-plt-3c.d: Likewise. * testsuite/ld-i386/pr26869.d: Likewise. * testsuite/ld-i386/report-reloc-1.d: Likewise. * testsuite/ld-ifunc/ifunc-2-i386-now.d: Likewise. * testsuite/ld-ifunc/ifunc-2-local-i386-now.d: Likewise. * testsuite/ld-ifunc/ifunc-2-local-x86-64-now.d: Likewise. * testsuite/ld-ifunc/ifunc-2-x86-64-now.d: Likewise. * testsuite/ld-ifunc/pr17154-x86-64.d: Likewise. * testsuite/ld-x86-64/bnd-branch-1-now.d: Likewise. * testsuite/ld-x86-64/bnd-ifunc-1-now.d: Likewise. * testsuite/ld-x86-64/bnd-ifunc-2-now.d: Likewise. * testsuite/ld-x86-64/bnd-ifunc-2.d: Likewise. * testsuite/ld-x86-64/bnd-plt-1-now.d: Likewise. * testsuite/ld-x86-64/bnd-plt-1.d: Likewise. * testsuite/ld-x86-64/ibt-plt-2a-x32.d: Likewise. * testsuite/ld-x86-64/ibt-plt-2a.d: Likewise. * testsuite/ld-x86-64/ibt-plt-3a-x32.d: Likewise. * testsuite/ld-x86-64/ibt-plt-3a.d: Likewise. * testsuite/ld-x86-64/ilp32-4.d: Likewise. * testsuite/ld-x86-64/load1c.d: Likewise. * testsuite/ld-x86-64/load1d.d: Likewise. * testsuite/ld-x86-64/pr13082-2b.d: Likewise. * testsuite/ld-x86-64/pr14207.d: Likewise. * testsuite/ld-x86-64/pr18176.d: Likewise. * testsuite/ld-x86-64/pr19162.d: Likewise. * testsuite/ld-x86-64/pr19636-2d.d: Likewise. * testsuite/ld-x86-64/pr19636-2l.d: Likewise. * testsuite/ld-x86-64/pr20253-1d.d: Likewise. * testsuite/ld-x86-64/pr20253-1f.d: Likewise. * testsuite/ld-x86-64/pr20253-1j.d: Likewise. * testsuite/ld-x86-64/pr20253-1l.d: Likewise. * testsuite/ld-x86-64/report-reloc-1-x32.d: Likewise. * testsuite/ld-x86-64/report-reloc-1.d: Likewise. * testsuite/ld-x86-64/export-class.exp (x86_64_export_class_test): Pass $NO_DT_RELR_LDFLAGS to linker. * testsuite/ld-x86-64/x86-64.exp: Pass $NO_DT_RELR_LDFLAGS to linker for some tests.
2022-01-12objdump, readelf: Emit "CU:" format only when wide output is requestedHans-Peter Nilsson2-2/+2
As pre-approved by Alan in https://sourceware.org/pipermail/binutils/2021-September/118019.html and I believe people have run into getting testsuite failures for test-environments with "long" directory names, at least once more since that time. Enough. I grepped the gas, binutils and ld testsuites for "CU:" to catch target-specific occurrences, but I noticed none. I chose to remove "CU:" on the objdump tests instead of changing options to get the wide format, so as to keep the name of the test consistent with actual options; but added it to the readelf options for the gas test as I believe the "CU:" format is preferable. Tested for cris-elf and native x86_64-pc-linux-gnu. binutils: * dwarf.c (display_debug_lines_decoded): Don't check the string length of the directory, instead emit the "CU: dir/name" format only if wide output is requested. * testsuite/binutils-all/dw5.W, testsuite/binutils-all/objdump.WL: Adjust accordingly. gas: * testsuite/gas/elf/dwarf-5-loc0.d: Add -W to readelf options.
2022-01-11ar: Add --thin for creating thin archivesFangrui Song1-0/+17
In many ar implementations (FreeBSD, elfutils, etc), -T has the X/Open System Interface specified semantics. Therefore -T for thin archives is not recommended for portability. -T is deprecated without diagnostics. PR binutils/28759 * ar.c (long_options): Add --thin. (usage) Add --thin. Deprecate -T without diagnostics. * doc/binutils.texi: Add doc. * NEWS: Mention --thin. * binutils/testsuite/binutils-all/ar.exp: Add tests.
2022-01-02Update year range in copyright notice of binutils filesAlan Modra45-45/+45
The result of running etc/update-copyright.py --this-year, fixing all the files whose mode is changed by the script, plus a build with --enable-maintainer-mode --enable-cgen-maint=yes, then checking out */po/*.pot which we don't update frequently. The copy of cgen was with commit d1dd5fcc38ead reverted as that commit breaks building of bfp opcodes files.
2021-12-16When loading separate debug info files, also attempt to locate a file based ↵Nick Clifton1-3/+3
upon the build-id. PR 28697 * dwarf.c (load_build_id_debug_file): New function. (try_build_id_prefix): New function. (check_for_and_load_links): Call load_build_id_debug_file. (debug_displays): Add entry for .note.gnu.build-id. * dwarf.h (enum dwarf_section_display_enum): Add note_gnu_build_id. * testsuite/binutils-all/debuginfod.exp (test_fetch_debuglink): Fix regexp for loads via debuglink section.
2021-11-23AArch64: Add support for AArch64 EFI (efi-*-aarch64).Tamar Christina2-0/+58
This adds support for efi-*-aarch64 by virtue of adding a new PEI target pei-aarch64-little. This is not a full target and only exists to support EFI at this time. This means that this target does not support relocation processing and is mostly a container format. This format has been added to elf based aarch64 targets such that efi images can be made natively on Linux. However this target is not valid for use with gas but only with objcopy. With these changes the resulting file is recognized as an efi image by third party tools: > pecli info hello.efi Metadata ================================================================================ MD5: 598c32a778b0f0deebe977fef8578c4e SHA1: 4580121edd5cb4dc40f51b28f171fd15250df84c SHA256: 3154bd7cf42433d1c957f6bf55a17ad8c57ed41b29df2d485703349fd6ff1d5c Imphash: Size: 47561 bytes Type: PE32+ executable (EFI application) (stripped to external PDB), for MS Windows Compile Time: 1970-01-01 00:00:00 (UTC - 0x0 ) Entry point: 0x2000 (section .text) Sections ================================================================================ Name RWX VirtSize VirtAddr RawAddr RawSize Entropy md5 .text R-X 0x5bb0 0x2000 0x400 0x5c00 6.39 551fbc264256a3f387de8a891500ae0d .reloc R-- 0xc 0x8000 0x6000 0x200 0.02 0c45f6d812d079821c1d54c09ab89e1d .data RW- 0x1d88 0x9000 0x6200 0x1e00 4.18 5d1137c09f01289dc62bf754f7290db3 .dynamic RW- 0xf0 0xb000 0x8000 0x200 0.34 5c94ed3206f05a277e6f04fbf131f131 .rela R-- 0xe58 0xc000 0x8200 0x1000 1.87 8b5c6bc30f3acb7ca7bf2e6789d68519 .dynsym R-- 0x138 0xd000 0x9200 0x200 0.96 bdcf5101da51aadc663ca8859f88138c Imports ================================================================================ Any magic number is based on the Microsoft PE specification [1]. [1] https://docs.microsoft.com/en-us/windows/win32/debug/pe-format bfd/ChangeLog: 2021-10-21 Tamar Christina <tamar.christina@arm.com> PR binutils/26206 * .gitignore (pe-aarch64igen.c): New. * Makefile.am (pei-aarch64.lo, pe-aarch64igen.lo, pei-aarch64.c, pe-aarch64igen.c): Add support. * Makefile.in: Likewise. * bfd.c (bfd_get_sign_extend_vma): Add pei-aarch64-little. * coff-aarch64.c: New file. * coffcode.h (coff_set_arch_mach_hook, coff_set_flags, coff_write_object_contents) Add aarch64 (aarch64_pei_vec) support. * config.bfd: Likewise. * configure: Likewise. * configure.ac: Likewise. * libpei.h (GET_OPTHDR_IMAGE_BASE, PUT_OPTHDR_IMAGE_BASE, GET_OPTHDR_SIZE_OF_STACK_RESERVE, PUT_OPTHDR_SIZE_OF_STACK_RESERVE, GET_OPTHDR_SIZE_OF_STACK_COMMIT, PUT_OPTHDR_SIZE_OF_STACK_COMMIT, GET_OPTHDR_SIZE_OF_HEAP_RESERVE, PUT_OPTHDR_SIZE_OF_HEAP_RESERVE, GET_OPTHDR_SIZE_OF_HEAP_COMMIT, PUT_OPTHDR_SIZE_OF_HEAP_COMMIT, GET_PDATA_ENTRY, _bfd_peAArch64_bfd_copy_private_bfd_data_common, _bfd_peAArch64_bfd_copy_private_section_data, _bfd_peAArch64_get_symbol_info, _bfd_peAArch64_only_swap_filehdr_out, _bfd_peAArch64_print_private_bfd_data_common, _bfd_peAArch64i_final_link_postscript, _bfd_peAArch64i_only_swap_filehdr_out, _bfd_peAArch64i_swap_aouthdr_in, _bfd_peAArch64i_swap_aouthdr_out, _bfd_peAArch64i_swap_aux_in, _bfd_peAArch64i_swap_aux_out, _bfd_peAArch64i_swap_lineno_in, _bfd_peAArch64i_swap_lineno_out, _bfd_peAArch64i_swap_scnhdr_out, _bfd_peAArch64i_swap_sym_in, _bfd_peAArch64i_swap_sym_out, _bfd_peAArch64i_swap_debugdir_in, _bfd_peAArch64i_swap_debugdir_out, _bfd_peAArch64i_write_codeview_record, _bfd_peAArch64i_slurp_codeview_record, _bfd_peAArch64_print_ce_compressed_pdata): New. * peXXigen.c (_bfd_XXi_swap_aouthdr_in, _bfd_XXi_swap_aouthdr_out, pe_print_pdata, _bfd_XX_print_private_bfd_data_common, _bfd_XX_bfd_copy_private_section_data, _bfd_XXi_final_link_postscript): Support COFF_WITH_peAArch64, * pei-aarch64.c: New file. * peicode.h (coff_swap_scnhdr_in, pe_ILF_build_a_bfd, pe_ILF_object_p): Support COFF_WITH_peAArch64. (jtab): Add dummy entry that traps. * targets.c (aarch64_pei_vec): New. binutils/ChangeLog: 2021-10-21 Tamar Christina <tamar.christina@arm.com> PR binutils/26206 * NEWS: Add new support. * objcopy.c (convert_efi_target): Add efi-*-aarch64 support. * testsuite/binutils-all/aarch64/pei-aarch64-little.d: New test. * testsuite/binutils-all/aarch64/pei-aarch64-little.s: New test. include/ChangeLog: 2021-10-21 Tamar Christina <tamar.christina@arm.com> PR binutils/26206 * coff/aarch64.h: New file. * coff/pe.h (IMAGE_FILE_MACHINE_ARM64): New.
2021-11-23binutils debuginfod testAlan Modra1-1/+2
A missing "return" resulted in this non-ELF fail: x86_64-w64-mingw32 +FAIL: debuginfod (create separate debug info file) Also, the debuginfod I have installed does not appear to handle non-native ELF objects, so only run the test when native. * testsuite/binutils-all/debuginfod.exp: Don't run test unless native ELF.
2021-11-17elfedit: Add --output-abiversion option to update ABIVERSIONH.J. Lu2-0/+16
* NEWS: Mention --output-abiversion. * elfedit.c (input_elf_abiversion): New. (output_elf_abiversion): Likewise. (update_elf_header): Update EI_ABIVERSION. (command_line_switch): Add OPTION_INPUT_ABIVERSION and OPTION_OUTPUT_ABIVERSION. (options): Add --input-abiversion and --output-abiversion. (usage): Likewise. (main): Handle --input-abiversion and --output-abiversion. * doc/binutils.texi: Document --input-abiversion and --output-abiversion. * testsuite/binutils-all/elfedit.exp: Run elfedit-6. * testsuite/binutils-all/elfedit-6.d: New file.
2021-10-24LoongArch binutils supportliuzhensong1-0/+1
2021-10-22 Chenghua Xu <xuchenghua@loongson.cn> Zhensong Liu <liuzhensong@loongson.cn> Weinan Liu <liuweinan@loongson.cn> binutils/ * NEWS: Mention LoongArch support. * readelf.c: Add LoongArch. * testsuite/binutils-all/objdump.exp: Add LoongArch.
2021-09-20riscv: print .2byte or .4byte before an unknown instruction encodingAndrew Burgess3-0/+67
When the RISC-V disassembler encounters an unknown instruction, it currently just prints the value of the bytes, like this: Dump of assembler code for function custom_insn: 0x00010132 <+0>: addi sp,sp,-16 0x00010134 <+2>: sw s0,12(sp) 0x00010136 <+4>: addi s0,sp,16 0x00010138 <+6>: 0x52018b 0x0001013c <+10>: 0x9c45 My proposal, in this patch, is to change the behaviour to this: Dump of assembler code for function custom_insn: 0x00010132 <+0>: addi sp,sp,-16 0x00010134 <+2>: sw s0,12(sp) 0x00010136 <+4>: addi s0,sp,16 0x00010138 <+6>: .4byte 0x52018b 0x0001013c <+10>: .2byte 0x9c45 Adding the .4byte and .2byte opcodes. The benefit that I see here is that in the patched version of the tools, the disassembler output can be fed back into the assembler and it should assemble to the same binary format. Before the patch, the disassembler output is invalid assembly. I've started a RISC-V specific test file under binutils so that I can add a test for this change. binutils/ChangeLog: * testsuite/binutils-all/riscv/riscv.exp: New file. * testsuite/binutils-all/riscv/unknown.d: New file. * testsuite/binutils-all/riscv/unknown.s: New file. opcodes/ChangeLog: * riscv-dis.c (riscv_disassemble_insn): Print a .%dbyte opcode before an unknown instruction, '%d' is replaced with the instruction length.
2021-09-03CC_FOR_TARGET et alAlan Modra1-4/+4
The top level Makefile, the ld Makefile and others, define CC_FOR_TARGET to be a compiler for the binutils target machine. This is the compiler that should be used for almost all tests with C source. There are _FOR_TARGET versions of CFLAGS, CXX, and CXXFLAGS too. This was all supposed to work with the testsuite .exp files using CC for the target compiler, and CC_FOR_HOST for the host compiler, with the makefiles passing CC=$CC_FOR_TARGET and CC_FOR_HOST=$CC to the runtest invocation. One exception to the rule of using CC_FOR_TARGET is the native-only ld bootstrap test, which uses the newly built ld to link a copy of itself. Since the files being linked were created with the host compiler, the boostrap test should use CC and CFLAGS, in case some host compiler option provides needed libraries automatically. However, bootstrap.exp used CC where it should have used CC_FOR_HOST. I set about fixing that problem, then decided that playing games in the makefiles with CC was a bad idea. Not only is it confusing, but other dejagnu code knows about CC_FOR_TARGET. See dejagnu/target.exp. So this patch gets rid of the makefile variable renaming and changes all the .exp files to use the correct _FOR_TARGET variables. CC_FOR_HOST and CFLAGS_FOR_HOST disappear. A followup patch will correct bootstrap.exp to use CFLAGS, and a number of other things I noticed. binutils/ * testsuite/lib/binutils-common.exp (run_dump_test): Use CC_FOR_TARGET and CFLAGS_FOR_TARGET rather than CC and CFLAGS. ld/ * Makefile.am (check-DEJAGNU): Don't set CC to CC_FOR_TARGET and similar. Pass variables with unchanged names. Don't set CC_FOR_HOST or CFLAGS_FOR_HOST. * Makefile.in: Regenerate. * testsuite/config/default.exp: Update default CC and similar. (compiler_supports, plug_opt): Use CC_FOR_TARGET. * testsuite/ld-cdtest/cdtest.exp: Replace all uses of CC with CC_FOR_TARGET, and similarly for CFLAGS, CXX and CXXFLAGS. * testsuite/ld-auto-import/auto-import.exp: Likewise. * testsuite/ld-cygwin/exe-export.exp: Likewise. * testsuite/ld-elf/dwarf.exp: Likewise. * testsuite/ld-elf/indirect.exp: Likewise. * testsuite/ld-elf/shared.exp: Likewise. * testsuite/ld-elfcomm/elfcomm.exp: Likewise. * testsuite/ld-elfvers/vers.exp: Likewise. * testsuite/ld-elfvsb/elfvsb.exp: Likewise. * testsuite/ld-elfweak/elfweak.exp: Likewise. * testsuite/ld-gc/gc.exp: Likewise. * testsuite/ld-ifunc/ifunc.exp: Likewise. * testsuite/ld-mn10300/mn10300.exp: Likewise. * testsuite/ld-pe/pe-compile.exp: Likewise. * testsuite/ld-pe/pe-run.exp: Likewise. * testsuite/ld-pe/pe-run2.exp: Likewise. * testsuite/ld-pie/pie.exp: Likewise. * testsuite/ld-plugin/lto.exp: Likewise. * testsuite/ld-plugin/plugin.exp: Likewise. * testsuite/ld-scripts/crossref.exp: Likewise. * testsuite/ld-selective/selective.exp: Likewise. * testsuite/ld-sh/sh.exp: Likewise. * testsuite/ld-shared/shared.exp: Likewise. * testsuite/ld-srec/srec.exp: Likewise. * testsuite/ld-undefined/undefined.exp: Likewise. * testsuite/ld-unique/unique.exp: Likewise. * testsuite/ld-x86-64/tls.exp: Likewise. * testsuite/lib/ld-lib.exp: Likewise. libctf/ * Makefile.am (check-DEJAGNU): Don't set CC to CC_FOR_TARGET. Pass CC and CC_FOR_TARGET. Don't set CC_FOR_HOST. * Makefile.in: Regenerate. * testsuite/config/default.exp: Update default CC and similar. * testsuite/lib/ctf-lib.exp (run_native_host_cmd): Use CC rather than CC_FOR_HOST. (run_lookup_test): Use CC_FOR_TARGET and CFLAGS_FOR_TARGET.
2021-08-30RISC-V: PR27916, Support mapping symbols.Nelson Chu6-10/+16
Similar to ARM/AARCH64, we add mapping symbols in the symbol table, to mark the start addresses of data and instructions. The $d means data, and the $x means instruction. Then the disassembler uses these symbols to decide whether we should dump data or instruction. Consider the mapping-04 test case, $ cat tmp.s .text .option norelax .option norvc .fill 2, 4, 0x1001 .byte 1 .word 0 .balign 8 add a0, a0, a0 .fill 5, 2, 0x2002 add a1, a1, a1 .data .word 0x1 # No need to add mapping symbols. .word 0x2 $ riscv64-unknown-elf-as tmp.s -o tmp.o $ riscv64-unknown-elf-objdump -d tmp.o Disassembly of section .text: 0000000000000000 <.text>: 0: 00001001 .word 0x00001001 # Marked $d, .fill directive. 4: 00001001 .word 0x00001001 8: 00000001 .word 0x00000001 # .byte + part of .word. c: 00 .byte 0x00 # remaining .word. d: 00 .byte 0x00 # Marked $d, odd byte of alignment. e: 0001 nop # Marked $x, nops for alignment. 10: 00a50533 add a0,a0,a0 14: 20022002 .word 0x20022002 # Marked $d, .fill directive. 18: 20022002 .word 0x20022002 1c: 2002 .short 0x2002 1e: 00b585b3 add a1,a1,a1 # Marked $x. 22: 0001 nop # Section tail alignment. 24: 00000013 nop * Use $d and $x to mark the distribution of data and instructions. Alignments of code are recognized as instructions, since we usually fill nops for them. * If the alignment have odd bytes, then we cannot just fill the nops into the spaces. We always fill an odd byte 0x00 at the start of the spaces. Therefore, add a $d mapping symbol for the odd byte, to tell disassembler that it isn't an instruction. The behavior is same as Arm and Aarch64. The elf/linux toolchain regressions all passed. Besides, I also disable the mapping symbols internally, but use the new objudmp, the regressions passed, too. Therefore, the new objudmp should dump the objects corretly, even if they don't have any mapping symbols. bfd/ pr 27916 * cpu-riscv.c (riscv_elf_is_mapping_symbols): Define mapping symbols. * cpu-riscv.h: extern riscv_elf_is_mapping_symbols. * elfnn-riscv.c (riscv_maybe_function_sym): Do not choose mapping symbols as a function name. (riscv_elf_is_target_special_symbol): Add mapping symbols. binutils/ pr 27916 * testsuite/binutils-all/readelf.s: Updated. * testsuite/binutils-all/readelf.s-64: Likewise. * testsuite/binutils-all/readelf.s-64-unused: Likewise. * testsuite/binutils-all/readelf.ss: Likewise. * testsuite/binutils-all/readelf.ss-64: Likewise. * testsuite/binutils-all/readelf.ss-64-unused: Likewise. gas/ pr 27916 * config/tc-riscv.c (make_mapping_symbol): Create a new mapping symbol. (riscv_mapping_state): Decide whether to create mapping symbol for frag_now. Only add the mapping symbols to text sections. (riscv_add_odd_padding_symbol): Add the mapping symbols for the riscv_handle_align, which have odd bytes spaces. (riscv_check_mapping_symbols): Remove any excess mapping symbols. (md_assemble): Marked as MAP_INSN. (riscv_frag_align_code): Marked as MAP_INSN. (riscv_init_frag): Add mapping symbols for frag, it usually called by frag_var. Marked as MAP_DATA for rs_align and rs_fill, and marked as MAP_INSN for rs_align_code. (s_riscv_insn): Marked as MAP_INSN. (riscv_adjust_symtab): Call riscv_check_mapping_symbols. * config/tc-riscv.h (md_cons_align): Defined to riscv_mapping_state with MAP_DATA. (TC_SEGMENT_INFO_TYPE): Record mapping state for each segment. (TC_FRAG_TYPE): Record the first and last mapping symbols for the fragments. The first mapping symbol must be placed at the start of the fragment. (TC_FRAG_INIT): Defined to riscv_init_frag. * testsuite/gas/riscv/mapping-01.s: New testcase. * testsuite/gas/riscv/mapping-01a.d: Likewise. * testsuite/gas/riscv/mapping-01b.d: Likewise. * testsuite/gas/riscv/mapping-02.s: Likewise. * testsuite/gas/riscv/mapping-02a.d: Likewise. * testsuite/gas/riscv/mapping-02b.d: Likewise. * testsuite/gas/riscv/mapping-03.s: Likewise. * testsuite/gas/riscv/mapping-03a.d: Likewise. * testsuite/gas/riscv/mapping-03b.d: Likewise. * testsuite/gas/riscv/mapping-04.s: Likewise. * testsuite/gas/riscv/mapping-04a.d: Likewise. * testsuite/gas/riscv/mapping-04b.d: Likewise. * testsuite/gas/riscv/mapping-norelax-04a.d: Likewise. * testsuite/gas/riscv/mapping-norelax-04b.d: Likewise. * testsuite/gas/riscv/no-relax-align.d: Updated. * testsuite/gas/riscv/no-relax-align-2.d: Likewise. include/ pr 27916 * opcode/riscv.h (enum riscv_seg_mstate): Added. opcodes/ pr 27916 * riscv-dis.c (last_map_symbol, last_stop_offset, last_map_state): Added to dump sections with mapping symbols. (riscv_get_map_state): Get the mapping state from the symbol. (riscv_search_mapping_symbol): Check the sorted symbol table, and then find the suitable mapping symbol. (riscv_data_length): Decide which data size we should print. (riscv_disassemble_data): Dump the data contents. (print_insn_riscv): Handle the mapping symbols. (riscv_symbol_is_valid): Marked mapping symbols as invalid.
2021-08-24objdump -S test fail on mingwAlan Modra3-12/+33
FAIL: objdump -S FAIL: objdump --source-comment is seen on mingw for the simple reason that gcc adds a .exe suffix on the output file if not already present. Fix that, and tidy some objcopy tests. * testsuite/lib/binutils-common.exp (exeext): New proc. * testsuite/binutils-all/objcopy.exp (exe, test_prog): Use it here. (objcopy_remove_relocations_from_executable): Catch objcopy errors. Only run on ELF targets. * testsuite/binutils-all/objdump.exp (exe): Set variable. (test_build_id_debuglink, test_objdump_S): Use exe file suffix.
2021-08-11Deprecate a.out support for NetBSD targets.John Ericson2-6/+3
As discussed previously, a.out support is now quite deprecated, and in some cases removed, in both Binutils itself and NetBSD, so this legacy default makes little sense. `netbsdelf*` and `netbsdaout*` still work allowing the user to be explicit about there choice. Additionally, the configure script warns about the change as Nick Clifton requested. One possible concern was the status of NetBSD on NS32K, where only a.out was supported. But per [1] NetBSD has removed support, and if it were to come back, it would be with ELF. The binutils implementation is therefore marked obsolete, per the instructions in the last message. With that patch and this one applied, I have confirmed the following: --target=i686-unknown-netbsd --target=i686-unknown-netbsdelf builds completely --target=i686-unknown-netbsdaout properly fails because target is deprecated. --target=vax-unknown-netbsdaout builds completely except for gas, where the target is deprecated. [1]: https://mail-index.netbsd.org/tech-toolchain/2021/07/19/msg004025.html --- bfd/config.bfd | 43 +++++++++++++-------- bfd/configure.ac | 5 +-- binutils/testsuite/binutils-all/nm.exp | 2 +- binutils/testsuite/lib/binutils-common.exp | 7 +--- config/picflag.m4 | 4 +- gas/configure.tgt | 9 +++-- gas/testsuite/gas/arm/blx-bl-convert.d | 2 +- gas/testsuite/gas/arm/blx-local-thumb.d | 2 +- gas/testsuite/gas/sh/basic.exp | 2 +- gdb/configure.host | 34 +++++++---------- gdb/configure.tgt | 2 +- gdb/testsuite/gdb.asm/asm-source.exp | 6 +-- intl/configure | 2 +- ld/configure.tgt | 44 +++++++++++----------- ld/testsuite/ld-arm/arm-elf.exp | 4 +- ld/testsuite/ld-elf/elf.exp | 2 +- ld/testsuite/ld-elf/shared.exp | 4 +- libiberty/configure | 4 +-
2021-08-11x86: have non-PE/COFF BEOS be recognized as ELFJan Beulich1-0/+5
BEOS, unless explicitly requesting *-*-beospe* targets, uses standard ELF. None of the newly enabled tests in the testsuite fail for me.
2021-07-21Remove `netbsdpe` supportJohn Ericson1-1/+0
netbsdpe was deprecated in c2ce831330e10dab4703094491f80b6b9a5c2289. Since then, a release has passed (2.37), and it was marked obselete in 5c9cbf07f3f972ecffe13d858010b3179df17b32. Unless I am mistaken, that means we can now remove support altogether. All branches in the "active" code are remove, and the target is additionally marked as obsolete next to the other removed ones for libbfd and gdb. Per [1] from the NetBSD toolchain list, PE/COFF support was removed a decade ago. Furthermore, the sole mention of this target in the binutils commit history was in 2002. Together, I'm led to believe this target hasn't seen much attention in quite a while. [1]: https://mail-index.netbsd.org/tech-toolchain/2021/06/16/msg003996.html bfd/ * config.bfd: Remove netbsdpe entry. binutils/ * configure.ac: Remove netbsdpe entry. * testsuite/lib/binutils-common.exp (is_pecoff_format): Likewise. * configure: Regenerate. gas/ * configure.tgt: Remove netbsdpe entry. gdb/ * configure.tgt: Add netbsdpe to removed targets. ld/ * configure.tgt: Remove netbsdpe entry. * testsuite/ld-bootstrap/bootstrap.exp: Likewise.
2021-07-13RISC-V: Enable elf attributes when default configure option isn't set.Nelson Chu6-1/+9
Since gcc commit, 3c70b3ca1ef58f302bf8c16d9e7c7bb8626408bf, we now enable elf attributes for all riscv targets by default in gcc. Therefore, I think binutils should have the same behavior, in case users are writing assembly files. If --enable-default-riscv-attribute isn't set, then we enable the elf attributes for all riscv targets by default. ChangLog: binutils/ * testsuite/binutils-all/readelf.s: Add comments for riscv. * testsuite/binutils-all/readelf.s-64: Likewise. * testsuite/binutils-all/readelf.s-64-unused: Likewise. * testsuite/binutils-all/readelf.ss: Likewise. * testsuite/binutils-all/readelf.ss-64: Likewise. * testsuite/binutils-all/readelf.ss-64-unused: Likewise. gas/ * configure.ac: If --enable-default-riscv-attribute isn't set, then we enable the elf attributes for all riscv targets by default. * configure: Regenerated.
2021-07-01Partially fix debuginfod tests in binutils testsuite.Nick Clifton1-5/+5
PR 28029 * testsuite/binutils-all/debuginfod.exp: Replace -wK with -wk.
2021-07-01readelf: Reset file position to beginning for thin archive membersAndrei Homescu2-0/+50
* readelf.c (process_archive): Reset file position to the beginning when calling process_object for thin archive members. * testsuite/binutils-all/readelf.exp: Add test. * testsuite/binutils-all/readelf.h.thin: New file.
2021-06-15readelf: report DF_1_PIE as "Position-Independent Executable"Alan Modra1-1/+1
I finally found time to teach readelf to identify PIEs in the file header display and program header display. So in place of "DYN (Shared object file)" which isn't completely true, show "DYN (Position-Independent Executable file)". It requires a little bit of untangling code in readelf due to process_program_headers setting up dynamic_addr and dynamic_size, needed to scan .dynamic for the DT_FLAGS_1 entry, and process_program_headers itself wanting to display the file type in some cases. At first I modified process_program_header using a "probe" parameter similar to get_section_headers in order to inhibit output, but decided it was cleaner to separate out locate_dynamic_sections. binutils/ * readelf.c (locate_dynamic_section, is_pie): New functions. (get_file_type): Replace e_type parameter with filedata. Call is_pie for ET_DYN. Update all callers. (process_program_headers): Use local variables dynamic_addr and dynamic_size, updating filedata on exit from function. Set dynamic_size of 1 to indicate no dynamic section or segment. Update tests of dynamic_size throughout. * testsuite/binutils-all/x86-64/pr27708.dump: Update expected output. ld/ * testsuite/ld-pie/vaddr-0.d: Update expected output. gdb/ * testsuite/lib/gdb.exp (exec_is_pie): Match new PIE readelf output.
2021-05-29MIPS/opcodes: Do not use CP0 register names for control registersMaciej W. Rozycki2-2/+2
The CP0 control register set has never been defined, however encodings for the CFC0 and CTC0 instructions remained available for implementers up until the MIPS32 ISA declared them invalid and causing the Reserved Instruction exception[1]. Therefore we handle them for both assembly and disassembly, however in the latter case the names of CP0 registers from the regular set are incorrectly printed if named registers are requested. This is because we do not define separate operand classes for coprocessor regular and control registers respectively, which means the disassembler has no way to tell the two cases apart. Consequently nonsensical disassembly is produced like: cfc0 v0,c0_random Later the MIPSr5 ISA reused the encodings for XPA ASE MFHC0 and MTHC0 instructions[2] although it failed to document them in the relevant opcode table until MIPSr6 only. Correct the issue then by defining a new register class, OP_REG_CONTROL, and corresponding operand codes, `g' and `y' for the two positions in the machine instruction a control register operand can take. Adjust the test cases affected accordingly. While at it swap the regular MIPS opcode table "cfc0" and "ctc0" entries with each other so that they come in the alphabetical order. References: [1] "MIPS32 Architecture For Programmers, Volume II: The MIPS32 Instruction Set", MIPS Technologies, Inc., Document Number: MD00086, Revision 1.00, August 29, 2002, Table A-9 "MIPS32 COP0 Encoding of rs Field", p. 242 [2] "MIPS Architecture For Programmers, Volume II-A: The MIPS32 Instruction Set", MIPS Technologies, Inc., Document Number: MD00086, Revision 5.04, December 11, 2013, Section 3.2 "Alphabetical List of Instructions", pp. 195, 216 include/ * opcode/mips.h: Document `g' and `y' operand codes. (mips_reg_operand_type): Add OP_REG_CONTROL enumeration constant. gas/ * tc-mips.c (convert_reg_type) <OP_REG_CONTROL>: New case. (macro) <M_TRUNCWS, M_TRUNCWD>: Use the `g' rather than `G' operand code. opcodes/ * mips-dis.c (print_reg) <OP_REG_COPRO>: Move control register handling code over to... <OP_REG_CONTROL>: ... this new case. * mips-opc.c (decode_mips_operand) <'g', 'y'>: New cases. (mips_builtin_opcodes): Update "cfc1", "ctc1", "cttc1", "cttc2", "cfc0", "ctc0", "cfc2", "ctc2", "cfc3", and "ctc3" entries replacing the `G' operand code with `g'. Update "cftc1" and "cftc2" entries replacing the `E' operand code with `y'. * micromips-opc.c (decode_micromips_operand) <'g'>: New case. (micromips_opcodes): Update "cfc1", "cfc2", "ctc1", and "ctc2" entries replacing the `G' operand code with `g'. binutils/ * testsuite/binutils-all/mips/mips-xpa-virt-1.d: Correct CFC0 operand disassembly. * testsuite/binutils-all/mips/mips-xpa-virt-3.d: Likewise.
2021-05-29MIPS/binutils/testsuite: Fix XPA and Virtualization ASE casesMaciej W. Rozycki4-4/+4
Fix commit 9785fc2a4d22 ("MIPS: Fix XPA base and Virtualization ASE instruction handling") and explicitly use the `mips:3000' machine for disassembly across the XPA base and XPA Virtualization ASE test cases, providing actual coverage for the `virt' and `xpa' disassembler options and removing failures for targets that default to those ASEs enabled: mipsisa32r2-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r2-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r2-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r2-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r2-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r2-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r2el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r2el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r2el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r2el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r2el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r2el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r3-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r3-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r3-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r3-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r3-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r3-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r3el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r3el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r3el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r3el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r3el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r3el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r5-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r5-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r5-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r5-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r5-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r5-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r5el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r5el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r5el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r5el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r5el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r5el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r6-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r6-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r6-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r6-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r6-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r6-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r6el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r6el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r6el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa32r6el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa32r6el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa32r6el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r2-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r2-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r2-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r2-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r2-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r2-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r2el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r2el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r2el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r2el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r2el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r2el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r3-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r3-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r3-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r3-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r3-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r3-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r3el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r3el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r3el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r3el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r3el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r3el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r5-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r5-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r5-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r5-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r5-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r5-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r5el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r5el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r5el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r5el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r5el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r5el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r6-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r6-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r6-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r6-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r6-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r6-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r6el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r6el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r6el-elf -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 mipsisa64r6el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 1 mipsisa64r6el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 2 mipsisa64r6el-linux -FAIL: MIPS XPA and Virtualization ASE instruction disassembly 3 This is because the test cases rely on these ASEs being disabled for disassembly by default and expect instructions belonging to these ASEs not to be shown unless explicitly enabled. The `mips-xpa-virt-4' test case passes regardless, but we want it to verify the explicit options do work, so use the `mips:3000' machine to set the defaults there as well. binutils/ * testsuite/binutils-all/mips/mips-xpa-virt-1.d: Use `mips:3000' machine for disassembly. * testsuite/binutils-all/mips/mips-xpa-virt-2.d: Likewise. * testsuite/binutils-all/mips/mips-xpa-virt-3.d: Likewise. * testsuite/binutils-all/mips/mips-xpa-virt-4.d: Likewise.
2021-04-21Adjust readelf's output so that section symbols without a name as shown with ↵Nick Clifton6-25/+25
their section name. binutils* readelf.c (print_dynamic_symbol): Print the section name for section symbols without a name of their own. * testsuite/binutils-all/mips/global-local-symtab-sort-n64t.d: Adjust expected output to allow for named section symbols. * testsuite/binutils-all/mips/global-local-symtab-sort-o32t.d: Likewise. * testsuite/binutils-all/readelf.s-64: Likewise. * testsuite/binutils-all/readelf.ss-64-unused: Likewise. * testsuite/binutils-all/readelf.ss-tmips: Likewise. * testsuite/binutils-all/readelf.ss-unused: Likewise. ld * testsuite/ld-aarch64/variant_pcs-now.d: Adjust expected output to allow for named section symbols. * testsuite/ld-aarch64/variant_pcs-r.d: Likewise. * testsuite/ld-aarch64/variant_pcs-shared.d: Likewise. * testsuite/ld-alpha/tlsbin.rd: Likewise. * testsuite/ld-alpha/tlsbinr.rd: Likewise. * testsuite/ld-alpha/tlspic.rd: Likewise. * testsuite/ld-arm/rodata-merge-map.sym: Likewise. * testsuite/ld-arm/script-type.sym: Likewise. * testsuite/ld-cris/libdso-2.d: Likewise. * testsuite/ld-cris/pr16044.d: Likewise. * testsuite/ld-elf/sec64k.exp: Likewise. * testsuite/ld-ia64/tlsbin.rd: Likewise. * testsuite/ld-ia64/tlspic.rd: Likewise. * testsuite/ld-mips-elf/global-local-symtab-sort-n64t.d: Likewise. * testsuite/ld-mips-elf/global-local-symtab-sort-o32t.d: Likewise. * testsuite/ld-mmix/bspec1.d: Likewise. * testsuite/ld-mmix/bspec2.d: Likewise. * testsuite/ld-mmix/local1.d: Likewise. * testsuite/ld-mmix/local3.d: Likewise. * testsuite/ld-mmix/local5.d: Likewise. * testsuite/ld-mmix/local7.d: Likewise. * testsuite/ld-mmix/undef-3.d: Likewise. * testsuite/ld-powerpc/tlsso.r: Likewise. * testsuite/ld-powerpc/tlsso32.r: Likewise. * testsuite/ld-powerpc/tlstocso.r: Likewise. * testsuite/ld-s390/tlsbin.rd: Likewise. * testsuite/ld-s390/tlsbin_64.rd: Likewise. * testsuite/ld-s390/tlspic.rd: Likewise. * testsuite/ld-s390/tlspic_64.rd: Likewise. * testsuite/ld-sparc/gotop32.rd: Likewise. * testsuite/ld-sparc/gotop64.rd: Likewise. * testsuite/ld-sparc/tlssunbin32.rd: Likewise. * testsuite/ld-sparc/tlssunbin64.rd: Likewise. * testsuite/ld-sparc/tlssunnopic32.rd: Likewise. * testsuite/ld-sparc/tlssunnopic64.rd: Likewise. * testsuite/ld-sparc/tlssunpic32.rd: Likewise. * testsuite/ld-sparc/tlssunpic64.rd: Likewise. * testsuite/ld-tic6x/common.d: Likewise. * testsuite/ld-tic6x/shlib-1.rd: Likewise. * testsuite/ld-tic6x/shlib-1b.rd: Likewise. * testsuite/ld-tic6x/shlib-1r.rd: Likewise. * testsuite/ld-tic6x/shlib-1rb.rd: Likewise. * testsuite/ld-tic6x/shlib-app-1.rd: Likewise. * testsuite/ld-tic6x/shlib-app-1b.rd: Likewise. * testsuite/ld-tic6x/shlib-app-1r.rd: Likewise. * testsuite/ld-tic6x/shlib-app-1rb.rd: Likewise. * testsuite/ld-tic6x/shlib-noindex.rd: Likewise. * testsuite/ld-tic6x/static-app-1.rd: Likewise. * testsuite/ld-tic6x/static-app-1b.rd: Likewise. * testsuite/ld-tic6x/static-app-1r.rd: Likewise. * testsuite/ld-tic6x/static-app-1rb.rd: Likewise. gas * testsuite/gas/aarch64/dwarf.d: Adjust expected output to allow for named section symbols. * testsuite/gas/arm/thumbver.d: Likewise. * testsuite/gas/bfin/loop_temps.d: Likewise. * testsuite/gas/elf/section2.e-arc: Likewise. * testsuite/gas/elf/section2.e-arm: Likewise. * testsuite/gas/elf/section2.e-csky: Likewise. * testsuite/gas/elf/section2.e-m32r: Likewise. * testsuite/gas/elf/section2.e-mips: Likewise. * testsuite/gas/elf/section2.e-msp430: Likewise. * testsuite/gas/elf/section2.e-riscv: Likewise. * testsuite/gas/elf/section2.e-rl78: Likewise. * testsuite/gas/elf/section2.e-rx: Likewise. * testsuite/gas/elf/section2.e-score: Likewise. * testsuite/gas/elf/section2.e-tic6x: Likewise. * testsuite/gas/elf/section2.e-unused: Likewise. * testsuite/gas/elf/section2.e-v850: Likewise. * testsuite/gas/elf/section2.e-xtensa: Likewise. * testsuite/gas/ia64/alias-ilp32.d: Likewise. * testsuite/gas/ia64/alias.d: Likewise. * testsuite/gas/ia64/global.d: Likewise. * testsuite/gas/microblaze/relax_size.elf: Likewise. * testsuite/gas/microblaze/relax_size2.elf: Likewise. * testsuite/gas/mips/global-local-symtab-sort-n64t.d: Likewise. * testsuite/gas/mips/global-local-symtab-sort-o32t.d: Likewise. * testsuite/gas/mmix/bspec-1.d: Likewise. * testsuite/gas/mmix/byte-1.d: Likewise. * testsuite/gas/mmix/comment-1.d: Likewise. * testsuite/gas/mmix/loc-1.d: Likewise. * testsuite/gas/mmix/loc-2.d: Likewise. * testsuite/gas/mmix/loc-3.d: Likewise. * testsuite/gas/mmix/loc-4.d: Likewise. * testsuite/gas/mmix/loc-5.d: Likewise. * testsuite/gas/tic6x/scomm-directive-4.d: Likewise.
2021-04-15PR27725, better objcopy -p timesAlan Modra1-0/+12
Nanosecond rather than second resolution. PR 27725 * configure.ac: Check for sys/time.h and utimensat. Use standard checks for mkstemp and mkdtemp. Whitespace. Check for nanosecond members of struct stat. * rename.c: Prefer sys/time.h for utimes over utime.h for utime. (STAT_TIMESPEC, STAT_TIMESPEC_NS): Define (get_stat_atime_ns, get_stat_mtime_ns): New inline functions. (get_stat_atime, get_stat_mtime): Likewise. (set_times): Choose first available of utimensat, utimes, utime. Use above inline functions to set timespec and timeval values. * configure: Regenerate. * config.in: Regenerate. * testsuite/binutils-all/objcopy.exp (objcopy_test): Add test of file timestamp when --preserve-dates is used.
2021-04-14elf: Set p_memsz to p_filesz for loadable PT_NOTE segmentH.J. Lu3-0/+71
Since p_memsz of the loadable PT_NOTE segment should be the same as p_filesz, set p_memsz on the loadable PT_NOTE segment when updating p_filesz. bfd/ PR binutils/27708 * elf.c (assign_file_positions_for_non_load_sections): Set p_memsz to p_filesz for the loadable PT_NOTE segment. binutils/ PR binutils/27708 * testsuite/binutils-all/x86-64/pr27708.dump: New file. * testsuite/binutils-all/x86-64/pr27708.exe.bz2: Likewise. * testsuite/binutils-all/x86-64/x86-64.exp: Run binutils/27708 test.
2021-03-04Gate the displaying of non-debug sections in separate debuginfo files.Nick Clifton6-18/+15
PR 27478 * objdump.c (process_links): New variable. (usage): Add --process-links. (long_options): Likewise. (dump_bfd): Stop processing once the bfd has been loaded unless this is the main file or process_links has been enabled. (main): Handle the process-links option. * readelf.c (process_links): New variable. (struct filedata): Add is_separate field. (options): Add --process-links. (usage): Likewise. (parse_args): Likewise. (process_file_header): Include the filename when dumping information for separate debuginfo files. (process_program_headers): Likewise. (process_section_headers): Likewise. (process_section_groups): Likewise. (process_relocs): Likewise. (process_dynamic_section): Likewise. (process_version_sections): Likewise. (display_lto_symtab): Likewise. (process_symbol_table): Likewise. (process_syminfo): Likewise. (initialise_dumps_by_name): Likewise. (process_section_contents): Likewise. (process_notes_at): Likewise. (process_notes): Likewise. (open_file): Add is_separate parameter. Use to initialise the is_separate field in the filedata structure. (open_deug): Update call to open_file. (process_object): Add processing of the contents of separate debuginfo files, gated by the process_links variable. (process_archive): Update call to open_file. (process_file): Initialise the is_separate field in the filedata structure. * dwarf.c (load_separate_debug_info_file): Only report the loading of a separate file if debug links are being dumped. * objcopy.c (keep_section_symbols): New variable. (enum command_line_switch): Add OPTION_KEEP_SYMBOLS. (strip_options): Add keep-section-symbols. (copy_options): Likewise. (copy_usage): Likewise. (strip_usage): Likewise. (copy_object): Keep section symbols if requested by command line option. (strip_main): Handle --keep-section-symbols. (copy_main): Likewise. * doc/binutils.texi: Document the new options. * NEWS: Mention the new features. * testsuite/binutils-all/compress.exp (test_gnu_debuglink): Update options passed to objdump. Use diff rather than cmp to compare the dumped data. * testsuite/binutils-all/objdump.WK2: Update regexp. * testsuite/binutils-all/objdump.WK3: Update regexp. * testsuite/binutils-all/objdump.exp: Use --process-links instead of --dwarf=follow-links. * testsuite/binutils-all/readelf.exp (readelf_test): Include readelf's output in the log when the test fails. Add the -P option to the -wKis test. * testsuite/binutils-all/readelf.wKis: Update expected output.
2021-03-01Warn for missing separate debug files only if neededH.J. Lu1-0/+15
We shouldn't warn missing separate debug files when debug info isn't needed. PR binutils/27486 * dwarf.c (load_separate_debug_info): Issue warning only if do_debug_links is set. * testsuite/binutils-all/compress.exp: Run objdump and readelf with missing debug file.
generated by cgit v1.1 at 2025-04-16 13:38:05 +0000