blob: bc6d52466949e35c82acda2f38413e92743f150f (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
.. SPDX-License-Identifier: GPL-2.0+
.. sectionauthor:: Wadim Egorov <w.egorov@phytec.de>
phyCORE-AM62x
=============
The `phyCORE-AM62x <https://www.phytec.com/product/phycore-am62x>`_ is a
SoM (System on Module) featuring TI's AM62x SoC. It can be used in combination
with different carrier boards. This module can come with different sizes and
models for DDR, eMMC, SPI NOR Flash and various SoCs from the AM62x family.
A development Kit, called `phyBOARD-Lyra <https://www.phytec.com/product/phyboard-am62x>`_
is used as a carrier board reference design around the AM62x SoM.
Quickstart
----------
* Download sources and TI firmware blobs
* Build Trusted Firmware-A
* Build OP-TEE
* Build U-Boot for the R5
* Build U-Boot for the A53
* Create bootable uSD Card
* Boot
Sources
-------
.. include:: ../ti/k3.rst
:start-after: .. k3_rst_include_start_boot_sources
:end-before: .. k3_rst_include_end_boot_sources
Build procedure
---------------
Setup the environment variables:
.. include:: ../ti/k3.rst
:start-after: .. k3_rst_include_start_common_env_vars_desc
:end-before: .. k3_rst_include_end_common_env_vars_desc
.. include:: ../ti/k3.rst
:start-after: .. k3_rst_include_start_board_env_vars_desc
:end-before: .. k3_rst_include_end_board_env_vars_desc
Set the variables corresponding to this platform:
.. include:: ../ti/k3.rst
:start-after: .. k3_rst_include_start_common_env_vars_defn
:end-before: .. k3_rst_include_end_common_env_vars_defn
.. code-block:: bash
$ export UBOOT_CFG_CORTEXR=phycore_am62x_r5_defconfig
$ export UBOOT_CFG_CORTEXA=phycore_am62x_a53_defconfig
$ export TFA_BOARD=lite
$ # we don't use any extra TFA parameters
$ unset TFA_EXTRA_ARGS
$ export OPTEE_PLATFORM=k3-am62x
$ export OPTEE_EXTRA_ARGS="CFG_WITH_SOFTWARE_PRNG=y"
.. include:: ../ti/am62x_sk.rst
:start-after: .. am62x_evm_rst_include_start_build_steps
:end-before: .. am62x_evm_rst_include_end_build_steps
uSD Card creation
-----------------
Use fdisk to partition the uSD card. The layout should look similar to:
.. code-block:: bash
$ sudo fdisk -l /dev/mmcblk0
Disk /dev/mmcblk0: 7.56 GiB, 8120172544 bytes, 15859712 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x6583d9a3
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 2048 264191 262144 128M c W95 FAT32 (LBA)
/dev/mmcblk0p2 264192 1934953 1670762 815.8M 83 Linux
Once partitioned, the boot partition has to be formatted with a FAT filesystem.
Assuming the uSD card is `/dev/mmcblk0`:
.. code-block:: bash
$ mkfs.vfat /dev/mmcblk0p1
To boot from a micro SD card on a HSFS device simply copy the following
artifacts to the FAT partition:
* tiboot3.bin from R5 build
* tispl.bin from Cortex-A build
* u-boot.img from Cortex-A build
Boot
----
Put the uSD card in the slot on the board and apply power. Check the serial
console for output.
Flash to SPI NOR
----------------
Below commands can be used to flash the SPI NOR flash; assuming
tiboot3.bin, tispl.bin and u-boot.img are stored on the uSD card.
.. code-block:: bash
sf probe
fatload mmc 1 ${loadaddr} tiboot3.bin
sf update $loadaddr 0x0 $filesize
fatload mmc 1 ${loadaddr} tispl.bin
sf update $loadaddr 0x80000 $filesize
fatload mmc 1 ${loadaddr} u-boot.img
sf update $loadaddr 0x280000 $filesize
Boot Modes
----------
The phyCORE-AM62x development kit supports booting from many different
interfaces. By default, the development kit is set to boot from the micro-SD
card. To change the boot device, DIP switches S5 and S6 can be used.
Boot switches should be changed with power off.
.. list-table:: Boot Modes
:widths: 16 16 16
:header-rows: 1
* - Switch Label
- SW5: 12345678
- SW6: 12345678
* - uSD
- 11000010
- 01000000
* - eMMC
- 11010010
- 00000000
* - OSPI
- 11010000
- 10000000
* - UART
- 11011100
- 00000000
Further Information
-------------------
Please see :doc:`../ti/am62x_sk` chapter for further AM62 SoC related documentation
and https://docs.phytec.com/phycore-am62x for vendor documentation.
|
