1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2020 PHYTEC Messtechnik GmbH
* Author: Teresa Remmet <t.remmet@phytec.de>
*/
#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/ddr.h>
#include <asm/arch/imx8mp_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/global_data.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/iomux-v3.h>
#include <hang.h>
#include <init.h>
#include <log.h>
#include <power/pmic.h>
#include <power/pca9450.h>
#include <spl.h>
DECLARE_GLOBAL_DATA_PTR;
int spl_board_boot_device(enum boot_device boot_dev_spl)
{
return BOOT_DEVICE_BOOTROM;
}
void spl_dram_init(void)
{
ddr_init(&dram_timing);
}
#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX8MP_PAD_I2C1_SCL__I2C1_SCL | PC,
.gpio_mode = MX8MP_PAD_I2C1_SCL__GPIO5_IO14 | PC,
.gp = IMX_GPIO_NR(5, 14),
},
.sda = {
.i2c_mode = MX8MP_PAD_I2C1_SDA__I2C1_SDA | PC,
.gpio_mode = MX8MP_PAD_I2C1_SDA__GPIO5_IO15 | PC,
.gp = IMX_GPIO_NR(5, 15),
},
};
int power_init_board(void)
{
struct pmic *p;
int ret;
ret = power_pca9450_init(0, 0x25);
if (ret)
printf("power init failed");
p = pmic_get("PCA9450");
pmic_probe(p);
/* BUCKxOUT_DVS0/1 control BUCK123 output */
pmic_reg_write(p, PCA9450_BUCK123_DVS, 0x29);
/* increase VDD_SOC to typical value 0.95V */
pmic_reg_write(p, PCA9450_BUCK2OUT_DVS0, 0x1C);
/* set WDOG_B_CFG to cold reset */
pmic_reg_write(p, PCA9450_RESET_CTRL, 0xA1);
return 0;
}
int board_fit_config_name_match(const char *name)
{
return 0;
}
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
static iomux_v3_cfg_t const uart_pads[] = {
MX8MP_PAD_UART2_RXD__UART2_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX8MP_PAD_UART2_TXD__UART2_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
static iomux_v3_cfg_t const wdog_pads[] = {
MX8MP_PAD_GPIO1_IO02__WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
};
int board_early_init_f(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
return 0;
}
void board_init_f(ulong dummy)
{
int ret;
arch_cpu_init();
init_uart_clk(1);
board_early_init_f();
ret = spl_early_init();
if (ret) {
debug("spl_early_init() failed: %d\n", ret);
hang();
}
preloader_console_init();
enable_tzc380();
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
power_init_board();
/* DDR initialization */
spl_dram_init();
}
|