1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
|
// SPDX-License-Identifier: GPL-2.0+
/*
* K+P iMX6Q KP_IMX6Q_TPC board configuration
*
* Copyright (C) 2018 Lukasz Majewski <lukma@denx.de>
*/
#include <common.h>
#include <asm/arch/clock.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx6-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <env.h>
#include <errno.h>
#include <miiphy.h>
#include <usb.h>
#include <usb/ehci-ci.h>
#include <led.h>
DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
#ifdef CONFIG_FEC_MXC
static int setup_fec_clock(void)
{
struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
/* set gpr1[21] to select anatop clock */
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK,
IOMUXC_GPR1_ENET_CLK_SEL_MASK);
return enable_fec_anatop_clock(0, ENET_50MHZ);
}
static int ar8031_phy_fixup(struct phy_device *phydev)
{
unsigned short val;
/* To enable AR8031 output a 125MHz clk from CLK_25M */
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
val &= 0xffe3;
val |= 0x18;
phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
/* introduce tx clock delay */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
val |= 0x0100;
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
return 0;
}
int board_phy_config(struct phy_device *phydev)
{
ar8031_phy_fixup(phydev);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#endif
#ifdef CONFIG_USB_EHCI_MX6
static void setup_usb(void)
{
/*
* Set daisy chain for otg_pin_id on MX6Q.
* For MX6DL, this bit is reserved.
*/
imx_iomux_set_gpr_register(1, 13, 1, 0);
}
#endif
int board_early_init_f(void)
{
#ifdef CONFIG_USB_EHCI_MX6
setup_usb();
#endif
#ifdef CONFIG_FEC_MXC
setup_fec_clock();
#endif
return 0;
}
int board_init(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
/* Enable eim_slow clocks */
setbits_le32(&mxc_ccm->CCGR6, 0x1 << MXC_CCM_CCGR6_EMI_SLOW_OFFSET);
return 0;
}
#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
/* 4 bit bus width */
{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
/* 8 bit bus width */
{"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
{NULL, 0},
};
#endif
int board_late_init(void)
{
#ifdef CONFIG_CMD_BMODE
add_board_boot_modes(board_boot_modes);
#endif
if (IS_ENABLED(CONFIG_LED))
led_default_state();
env_set("boardname", "kp-tpc");
env_set("boardsoc", "imx6q");
return 0;
}
int checkboard(void)
{
puts("Board: K+P KP_IMX6Q_TPC i.MX6Q\n");
return 0;
}
|
