aboutsummaryrefslogtreecommitdiff
path: root/Bindings/serial/serial.yaml
blob: ffc9198ae21469de249c87da75e27521bc2a419f (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/serial/serial.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Serial Interface Generic

maintainers:
  - Rob Herring <robh@kernel.org>
  - Greg Kroah-Hartman <gregkh@linuxfoundation.org>

description:
  This document lists a set of generic properties for describing UARTs in a
  device tree.  Whether these properties apply to a particular device depends
  on the DT bindings for the actual device.

  Each enabled UART may have an optional "serialN" alias in the "aliases" node,
  where N is the port number (non-negative decimal integer) as printed on the
  label next to the physical port.

properties:
  $nodename:
    pattern: "^serial(@.*)?$"

  label: true

  cts-gpios:
    maxItems: 1
    description:
      Must contain a GPIO specifier, referring to the GPIO pin to be used as
      the UART's CTS line.

  dcd-gpios:
    maxItems: 1
    description:
      Must contain a GPIO specifier, referring to the GPIO pin to be used as
      the UART's DCD line.

  dsr-gpios:
    maxItems: 1
    description:
      Must contain a GPIO specifier, referring to the GPIO pin to be used as
      the UART's DSR line.

  dtr-gpios:
    maxItems: 1
    description:
      Must contain a GPIO specifier, referring to the GPIO pin to be used as
      the UART's DTR line.

  rng-gpios:
    maxItems: 1
    description:
      Must contain a GPIO specifier, referring to the GPIO pin to be used as
      the UART's RNG line.

  rts-gpios:
    maxItems: 1
    description:
      Must contain a GPIO specifier, referring to the GPIO pin to be used as
      the UART's RTS line.

  uart-has-rtscts:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      The presence of this property indicates that the UART has dedicated lines
      for RTS/CTS hardware flow control, and that they are available for use
      (wired and enabled by pinmux configuration).  This depends on both the
      UART hardware and the board wiring.

  rx-tx-swap:
    type: boolean
    description: RX and TX pins are swapped.

  cts-rts-swap:
    type: boolean
    description: CTS and RTS pins are swapped.

  rx-threshold:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      RX FIFO threshold configuration (in bytes).

  tx-threshold:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      TX FIFO threshold configuration (in bytes).

patternProperties:
  "^(bluetooth|bluetooth-gnss|gnss|gps|mcu|onewire)$":
    if:
      type: object
    then:
      description:
        Serial attached devices shall be a child node of the host UART device
        the slave device is attached to. It is expected that the attached
        device is the only child node of the UART device. The slave device node
        name shall reflect the generic type of device for the node.

      properties:
        compatible:
          description:
            Compatible of the device connected to the serial port.

        max-speed:
          $ref: /schemas/types.yaml#/definitions/uint32
          description:
            The maximum baud rate the device operates at.
            This should only be present if the maximum is less than the slave
            device can support.  For example, a particular board has some
            signal quality issue or the host processor can't support higher
            baud rates.

        current-speed:
          $ref: /schemas/types.yaml#/definitions/uint32
          description: |
            The current baud rate the device operates at.
            This should only be present in case a driver has no chance to know
            the baud rate of the slave device.
            Examples:
              * device supports auto-baud
              * the rate is setup by a bootloader and there is no way to reset
                the device
              * device baud rate is configured by its firmware but there is no
                way to request the actual settings

      required:
        - compatible

if:
  required:
    - uart-has-rtscts
then:
  properties:
    cts-gpios: false
    rts-gpios: false

additionalProperties: true

examples:
  - |
    serial@1234 {
        compatible = "ns16550a";
        reg = <0x1234 0x20>;
        interrupts = <1>;

        bluetooth {
            compatible = "brcm,bcm4330-bt";
            interrupt-parent = <&gpio>;
            interrupts = <10>;
        };
    };