From 8fe11b8901a31d11990488c82bc23612589d57be Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Wed, 2 Sep 2015 10:40:24 +0900 Subject: powerpc: ppc4xx: remove lwmon5 support This has not been converted to Generic Board, so should be removed. (See doc/README.generic-board for details.) Remove CONFIG_LWMON5 references. (Also, remove undefined CONFIG_WD_MAX_RATE while I am here.) Signed-off-by: Masahiro Yamada Cc: Stefan Roese --- board/lwmon5/init.S | 75 ----------------------------------------------------- 1 file changed, 75 deletions(-) delete mode 100644 board/lwmon5/init.S (limited to 'board/lwmon5/init.S') diff --git a/board/lwmon5/init.S b/board/lwmon5/init.S deleted file mode 100644 index e5207c2..0000000 --- a/board/lwmon5/init.S +++ /dev/null @@ -1,75 +0,0 @@ -/* - * (C) Copyright 2007 - * Stefan Roese, DENX Software Engineering, sr@denx.de. - * - * Copyright (C) 2002 Scott McNutt - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/************************************************************************** - * TLB TABLE - * - * This table is used by the cpu boot code to setup the initial tlb - * entries. Rather than make broad assumptions in the cpu source tree, - * this table lets each board set things up however they like. - * - * Pointer to the table is returned in r1 - * - *************************************************************************/ - .section .bootpg,"ax" - .globl tlbtab - -tlbtab: - tlbtab_start - - /* - * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the - * speed up boot process. It is patched after relocation to enable SA_I - */ - tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G) - - /* - * TLB entries for SDRAM are not needed on this platform. - * They are dynamically generated in the SPD DDR(2) detection - * routine. - */ - -#ifdef CONFIG_SYS_INIT_RAM_DCACHE - /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */ - tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G) -#endif - - /* TLB-entry for PCI Memory */ - tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG) - tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG) - tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG) - tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG) - - /* TLB-entry for the FPGA Chip select 2 */ - tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G) - - /* TLB-entry for the FPGA Chip select 3 */ - tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G) - - /* TLB-entry for the LIME Controller */ - tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G) - tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G) - tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G) - tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G) - - /* TLB-entry for Internal Registers & OCM */ - tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0, AC_RWX | SA_I) - - /*TLB-entry PCI registers*/ - tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG) - - /* TLB-entry for peripherals */ - tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG) - - tlbtab_end -- cgit v1.1