From 03f9d7d1749fddf147823549e6965f6fb13faad6 Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Fri, 20 Jun 2014 13:54:55 +0900 Subject: mpc8xx: remove fads board support These boards are old enough and have no maintainers. Signed-off-by: Masahiro Yamada --- board/fads/fads.h | 468 ------------------------------------------------------ 1 file changed, 468 deletions(-) delete mode 100644 board/fads/fads.h (limited to 'board/fads/fads.h') diff --git a/board/fads/fads.h b/board/fads/fads.h deleted file mode 100644 index 1be00b9..0000000 --- a/board/fads/fads.h +++ /dev/null @@ -1,468 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * Derived from FADS860T definitions by Magnus Damm, Helmut Buchsbaum, - * and Dan Malek - * - * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com - * - * This header file contains values common to all FADS family boards. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/**************************************************************************** - * Flash Memory Map as used by U-Boot: - * - * Start Address Length - * +-----------------------+ 0xFE00_0000 Start of Flash ----------------- - * | | 0xFE00_0100 Reset Vector - * + + 0xFE0?_???? - * | U-Boot code | - * | | - * +-----------------------+ 0xFE04_0000 (sector border) - * | | - * | | - * | U-Boot environment | - * | | ^ - * | | | U-Boot - * +=======================+ 0xFE08_0000 (sector border) ----------------- - * | Available | | Applications - * | ... | v - * - *****************************************************************************/ - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_NFSBOOTCOMMAND \ - "dhcp;" \ - "setenv bootargs root=/dev/nfs rw nfsroot=$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;" \ - "bootm" - -#define CONFIG_BOOTCOMMAND \ - "setenv bootargs root=/dev/mtdblock2 rw mtdparts=phys:1280K(ROM)ro,-(root) "\ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:eth0:off;" \ - "bootm fe080000" - -#undef CONFIG_BOOTARGS - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -#if !defined(CONFIG_MPC885ADS) -#define CONFIG_BZIP2 /* include support for bzip2 compressed images */ -#endif - -/* - * New MPC86xADS and MPC885ADS provide two Ethernet connectivity options: - * 10Mbit/s on SCC and 100Mbit/s on FEC. FADS provides SCC Ethernet on - * motherboard and FEC Ethernet on daughterboard. All new PQ1 chips have - * got FEC so FEC is the default. - */ -#undef CONFIG_SCC1_ENET /* Disable SCC1 ethernet */ -#define CONFIG_FEC_ENET /* Use FEC ethernet */ - -#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) -#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured -#endif - -#ifdef CONFIG_FEC_ENET -#define CONFIG_SYS_DISCOVER_PHY -#define CONFIG_MII_INIT 1 -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -#if !defined(FADS_COMMANDS_ALREADY_DEFINED) -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_JFFS2 -#define CONFIG_CMD_MII -#define CONFIG_CMD_PCMCIA -#define CONFIG_CMD_PING - -#endif - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_LONGHELP /* #undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#if defined(CONFIG_MPC86xADS) || defined(CONFIG_MPC885ADS) /* New ADS or Duet */ -#define CONFIG_SYS_SDRAM_SIZE 0x00800000 /* 8 Mbyte */ -/* - * 2048 SDRAM rows - * 1000 factor s -> ms - * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration - * 4 Number of refresh cycles per period - * 64 Refresh cycle in ms per number of rows - */ -#define CONFIG_SYS_PTA_PER_CLK ((2048 * 64 * 1000) / (4 * 64)) -#elif defined(CONFIG_FADS) /* Old/new FADS */ -#define CONFIG_SYS_SDRAM_SIZE 0x00400000 /* 4 Mbyte */ -#else /* Old ADS */ -#define CONFIG_SYS_SDRAM_SIZE 0x00000000 /* No SDRAM */ -#endif - -#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ -#if (CONFIG_SYS_SDRAM_SIZE) -#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_SDRAM_SIZE /* 1 ... SDRAM_SIZE */ -#else -#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ -#endif /* CONFIG_SYS_SDRAM_SIZE */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 KB for monitor */ - -#ifdef CONFIG_BZIP2 -#define CONFIG_SYS_MALLOC_LEN (2500 << 10) /* Reserve ~2.5 MB for malloc() */ -#else -#define CONFIG_SYS_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */ -#endif /* CONFIG_BZIP2 */ - -/*----------------------------------------------------------------------- - * Flash organization - */ -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */ -#define CONFIG_ENV_OFFSET CONFIG_ENV_SECT_SIZE -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment */ -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -#define CONFIG_SYS_DIRECT_FLASH_TFTP - -#if defined(CONFIG_CMD_JFFS2) - -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition, whole device */ -#undef CONFIG_CMD_MTDPARTS -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_CMD_MTDPARTS -#define MTDIDS_DEFAULT "nor0=fads0,nor1=fads-1,nor2=fads-2,nor3=fads-3" -#define MTDPARTS_DEFAULT "mtdparts=fads-0:-@1m(user1),fads-1:-(user2),fads-2:-(user3),fads-3:-(user4)" -*/ - -#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS -#endif - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ - -/*----------------------------------------------------------------------- - * I2C configuration - */ -#if defined(CONFIG_CMD_I2C) -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address defaults */ -#define CONFIG_SYS_I2C_SLAVE 0x7F -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR SCCR_TBS - -/*----------------------------------------------------------------------- - * DER - Debug Enable Register - *----------------------------------------------------------------------- - * Set to zero to prevent the processor from entering debug mode - */ -#define CONFIG_SYS_DER 0 - -/* Because of the way the 860 starts up and assigns CS0 the entire - * address space, we have to set the memory controller differently. - * Normally, you write the option register first, and then enable the - * chip select by writing the base register. For CS0, you must write - * the base register first, followed by the option register. - */ - -/* - * Init Memory Controller: - * - * BR0/OR0 (Flash) - * BR1/OR1 (BCSR) - */ -/* the other CS:s are determined by looking at parameters in BCSRx */ - -#define BCSR_ADDR ((uint) 0xFF080000) - -#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ - -/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 8 Mbyte until detected */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_V ) - -/* BCSRx - Board Control and Status Registers */ -#define CONFIG_SYS_OR1_PRELIM 0xFFFF8110 /* 64Kbyte address space */ -#define CONFIG_SYS_BR1_PRELIM ((BCSR_ADDR) | BR_V) - -/* values according to the manual */ - -#define BCSR0 ((uint) (BCSR_ADDR + 0x00)) -#define BCSR1 ((uint) (BCSR_ADDR + 0x04)) -#define BCSR2 ((uint) (BCSR_ADDR + 0x08)) -#define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) -#define BCSR4 ((uint) (BCSR_ADDR + 0x10)) - -/* - * (F)ADS bitvalues by Helmut Buchsbaum - * - * See User's Manual for a proper - * description of the following structures - */ - -#define BCSR0_ERB ((uint)0x80000000) -#define BCSR0_IP ((uint)0x40000000) -#define BCSR0_BDIS ((uint)0x10000000) -#define BCSR0_BPS_MASK ((uint)0x0C000000) -#define BCSR0_ISB_MASK ((uint)0x01800000) -#define BCSR0_DBGC_MASK ((uint)0x00600000) -#define BCSR0_DBPC_MASK ((uint)0x00180000) -#define BCSR0_EBDF_MASK ((uint)0x00060000) - -#define BCSR1_FLASH_EN ((uint)0x80000000) -#define BCSR1_DRAM_EN ((uint)0x40000000) -#define BCSR1_ETHEN ((uint)0x20000000) -#define BCSR1_IRDEN ((uint)0x10000000) -#define BCSR1_FLASH_CFG_EN ((uint)0x08000000) -#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) -#define BCSR1_BCSR_EN ((uint)0x02000000) -#define BCSR1_RS232EN_1 ((uint)0x01000000) -#define BCSR1_PCCEN ((uint)0x00800000) -#define BCSR1_PCCVCC0 ((uint)0x00400000) -#define BCSR1_PCCVPP_MASK ((uint)0x00300000) -#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) -#define BCSR1_RS232EN_2 ((uint)0x00040000) -#define BCSR1_SDRAM_EN ((uint)0x00020000) -#define BCSR1_PCCVCC1 ((uint)0x00010000) - -#define BCSR1_PCCVCCON BCSR1_PCCVCC0 - -#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) -#define BCSR2_FLASH_PD_SHIFT 28 -#define BCSR2_DRAM_PD_MASK ((uint)0x07800000) -#define BCSR2_DRAM_PD_SHIFT 23 -#define BCSR2_EXTTOLI_MASK ((uint)0x00780000) -#define BCSR2_DBREVNR_MASK ((uint)0x00030000) - -#define BCSR3_DBID_MASK ((ushort)0x3800) -#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) -#define BCSR3_BREVNR0 ((ushort)0x0080) -#define BCSR3_FLASH_PD_MASK ((ushort)0x0070) -#define BCSR3_BREVN1 ((ushort)0x0008) -#define BCSR3_BREVN2_MASK ((ushort)0x0003) - -#define BCSR4_ETHLOOP ((uint)0x80000000) -#define BCSR4_TFPLDL ((uint)0x40000000) -#define BCSR4_TPSQEL ((uint)0x20000000) -#define BCSR4_SIGNAL_LAMP ((uint)0x10000000) -#if defined(CONFIG_MPC823) -#define BCSR4_USB_EN ((uint)0x08000000) -#define BCSR4_USB_SPEED ((uint)0x04000000) -#define BCSR4_VCCO ((uint)0x02000000) -#define BCSR4_VIDEO_ON ((uint)0x00800000) -#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) -#define BCSR4_VIDEO_RST ((uint)0x00200000) -#define BCSR4_MODEM_EN ((uint)0x00100000) -#define BCSR4_DATA_VOICE ((uint)0x00080000) -#elif defined(CONFIG_MPC850) -#define BCSR4_DATA_VOICE ((uint)0x00080000) -#elif defined(CONFIG_MPC860SAR) -#define BCSR4_UTOPIA_EN ((uint)0x08000000) -#else /* MPC860T and other chips with FEC */ -#define BCSR4_FETH_EN ((uint)0x08000000) -#define BCSR4_FETHCFG0 ((uint)0x04000000) -#define BCSR4_FETHFDE ((uint)0x02000000) -#define BCSR4_FETHCFG1 ((uint)0x00400000) -#define BCSR4_FETHRST ((uint)0x00200000) -#endif - -/* BSCR5 exists on MPC86xADS and MPC885ADS only */ - -#define CONFIG_SYS_PHYDEV_ADDR (BCSR_ADDR + 0x20000) - -#define BCSR5 (CONFIG_SYS_PHYDEV_ADDR + 0x300) - -#define BCSR5_MII2_EN 0x40 -#define BCSR5_MII2_RST 0x20 -#define BCSR5_T1_RST 0x10 -#define BCSR5_ATM155_RST 0x08 -#define BCSR5_ATM25_RST 0x04 -#define BCSR5_MII1_EN 0x02 -#define BCSR5_MII1_RST 0x01 - -/* We don't use the 8259. -*/ -#define NR_8259_INTS 0 - -/*----------------------------------------------------------------------- - * PCMCIA stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -/*----------------------------------------------------------------------- - * IDE/ATA stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_MAC_PARTITION 1 -#define CONFIG_DOS_PARTITION 1 -#define CONFIG_ISO_PARTITION 1 - -#undef CONFIG_ATAPI -#if 0 /* does not make sense when CONFIG_CMD_IDE is not enabled, too */ -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ -#endif -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 2 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 - -#define CONFIG_DISK_SPINUP_TIME 1000000 -/* #undef CONFIG_DISK_SPINUP_TIME */ /* usin Compact Flash */ -- cgit v1.1