Age | Commit message (Collapse) | Author | Files | Lines |
|
The current exit codes of 128 and 129 are useful in that they do not
conflict with those returned by tools, but they are not actually valid.
It seems better to pick some codes which work with 'bit bisect run'.
Update them to 100 (for errors) and 101 (for warnings).
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
A few of these have been done. Drop those and add some new ideas.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These are becoming more common now. They cause boards to show warnings
which can be mistaking for compiler warnings.
Add a buildman option to ignore them. This option works only with the
summary option (-s). It does not affect the build process.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Unfortunately the plague of device-tree warnings has not lifted. These
warnings infiltrate almost every build, adding noise and confusion.
Add a buildman option to ignore them. This option works only with the
summary option (-s). It does not affect the build process.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present buildman defaults to running 'mrproper' on every thread before
it starts building commits for each board. This can add a delay of about 5
seconds to the start of the process, since the tools and other invariants
must be rebuilt.
In particular, a build without '-b', to build current source, runs much
slower without -I, since any existing build is removed, thus losing the
possibility of an incremental build.
Partly this behaviour was to avoid strange build-system problems caused by
running 'make defconfig' for one board and then one with a different
architecture. But these problems were fixed quite a while ago.
The -I option (which disabled mrproper) was introduced four years ago and
does not seem to cause any problems with builds.
So make -I the default and deprecate the option. To allow use of
'mrproper', add a new -m flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Make a few additions and change some wording in the workflow
documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This option may be frequency used, so mention that it can be abbreviated
to --bo
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Make a few updates to this important section of the documentation, to
make things clearer.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When buildman finishes it leaves the last summary line visible, which
shows the number of successful builds, builds with warnings and builds
with errors.
It is useful also to see how many builds were done in total along with
the time taken. Show these on a separate line before buildman finishes.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
If a progress message is longer than the terminal line it will scroll the
terminal. Limit the messages to the terminal width.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is nice to see the actual number of builds remaining to complete. Add
this in the progress message, using a different colour.
Drop the unnecessary 'name' variable while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The commit counter is a hangover from when buildman processed each board
for a commit. Now buildman processes each commit for a board, so this
output is never triggered.
Delete it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Fetching updated versions of a repo can take time. At present buildman
gives no indication that it is doing this.
Add a message to explain the delay.
Tidy up a few other messages while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The new feature in terminal can be used by buildman. Update the Builder
class accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When outputing a progress line we don't want it to go past the end of the
current terminal line, or it will not be possible to erase it. Add an
option to Print() which allows limiting the output to the terminal width.
Since ANSI sequences do not take up space on the terminal, these are
removed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When printing progress it is useful to print a message and leave the
cursor at the end of the line until the operation is finished. When it is
finished, the line needs to be erased so a new line can start in its place.
Add a function to handle clearing a line previously written by
terminal.Print()
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This does not seem to work on Python 3. Update the code to use the
built-in support.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present the board names shown with -l are separated by commas. This
makes it hard to double-click to select a particular board. Also it is not
possible to select all boards and paste them as arguments to a subsequent
buildman run, since buildman requires spaces to separate the list on the
command line, not commas.
Change the output format to use spaces instead of commas.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is quite hard to see the list of board for each error line since the
colour is the same as the actual error line. Show the board list in
magenta so that it is easier to distinguish them.
There is no point in checking the colour of the overall line, since there
are now multiple colours. So drop those tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present the string for each error line is created in _CalcErrorDelta()
and used to create the summary output. This is inflexible since all the
information (error/warning character, error line, list of boards with that
error line) is munged together in a string.
Create an object to hold this information and only convert it to a string
when printing the actual output.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present warnings are shown in yellow in the summary (-s) but magenta in
the detail listing (-e). Use yellow in both.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a test to cover this flag, which adds the name of each board to each
error/warning line.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The split/join code is repeated in a lot of places. Add a function to
handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
We want to add a few more tests similar to testOutput(). Split its logic
into a function which runs buildman to get the output and another which
checks the output. This will make it easier to reuse the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rather than having a few tests handle this themselves, create the
temporary directory in the setUp() method and remove it in tearDown().
This will make it easier to add more tests.
Only testOutput and testGit() actually need it, but it doesn't add to the
test time noticeably to do this for all tests in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rather than using the absolute array index, use an interator to work
through the expected output lines. This is easier to follow.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Buildman should output the right colours for each error/warning line. Some
of these checks are missing. Add them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Reduce the amount of repeated code by creating an _OutputErrLines()
function to hold this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Fix some errors pointed out by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
commit 7298e422504e ("mkimage: fit: add support to encrypt image with
aes") added a new copyfile() function as part of the FIT image creation
flow. This function as currently written creates the final image with a
mode of 0700 (before umask), differing from the old behavior of 0666.
Since there doesn't seem to be any reason to make the image executable
or non-group, non-other readable, change the mask to 0666 to preserve
the old behavior.
Fixes: 7298e422504e ("mkimage: fit: add support to encrypt image with aes")
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
|
|
Quite often on a series that has clean-up patches, the individual patches
may fit within the cc limit but the cover letter does not. Apply the same
limit to the cover letter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
|
|
There is no point in setting the ARCH environment variable since the
U-Boot build system no-longer uses it.
It seems safe to drop this feature since it was only recently added.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This is useful in some situations, in particular with -w and when building
in-tree. Now that we are more careful about what we remove in
_PrepareOutputSpace(), it should be safe to relax this restriction.
Update the progress information also so it is clear what buildman is
doing. Remove files can take a long time.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present buildman removes any directory it doesn't intend to write
output into. This is overly expansive since if the output directory
happens to be somewhere with existing files, they may be removed. Using
an existing directory for buildman is not a good practice, but since the
result might be catastrophic, it is best to guard against it.
A previous commit[1] fixed this by refusing to write to a subdirectory
of the current directory, assumed to have U-Boot source code. But we can
do better by only removing directories that look like the ones buildman
creates.
Update the code to do this and add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
[1] 409fc029c40 tools: buildman: Don't use the working dir as build dir
|
|
Sometimes we don't want buildman to return failure if it seems warnings.
Add a -W option to support this. If buildman detects warnings (and no
errors) it will return an exit code of 0 (success).
Note that the definition of 'warnings' includes the migration warnings
produced by U-Boot, such as:
===================== WARNING ======================
This board does not use CONFIG_DM_MMC. Please update
...
====================================================
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This help is a bit ambiguous. It only does anything if asked to show size
changes with -S. Update the help and the function comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is useful to run a simple build and put all the output in a single
directory. Add a -w option to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This class has a few more members now. Add documentation for them and fix
a nit in the 'commits' comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This adds support to fetch gcc 9.2.0 toolchains.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Align Kconfig and Kbuild logic to Linux 4.19 release with minimal impact
on files outside of this scope.
Our previous Kconfig sync was done by commit 5972ff077e0f ("kconfig /
kbuild: re-sync with Linux 4.18").
In this particular re-sync in order to keep clang support working a
number of related changes needed to be pulled in that had been missed
previously. Not all of these changes we easily traceable and so have
been omitted from the list below.
The imported Linux commits are:
[From prior to v4.18]
9f3f1fd29976 kbuild: Add __cc-option macro
d7f14c66c273 kbuild: Enable Large File Support for hostprogs
6d79a7b424a5 kbuild: suppress warnings from 'getconf LFS_*'
24403874316a Shared library support
86a9df597cdd kbuild: fix linker feature test macros when cross compiling with Clang
0294e6f4a000 kbuild: simplify ld-option implementation
[From v4.18 to v4.19]
96f14fe738b6 kbuild: Rename HOSTCFLAGS to KBUILD_HOSTCFLAGS
10844aebf448 kbuild: Rename HOSTCXXFLAGS to KBUILD_HOSTCXXFLAGS
b90a368000ab kbuild: Rename HOSTLDFLAGS to KBUILD_HOSTLDFLAGS
8377bd2b9ee1 kbuild: Rename HOST_LOADLIBES to KBUILD_HOSTLDLIBS
f92d19e0ef9b kbuild: Use HOST*FLAGS options from the command line
4ab3b80159d4 kconfig: check for pkg-config on make {menu,n,g,x}config
693359f7ac90 kconfig: rename SYMBOL_AUTO to SYMBOL_NO_WRITE
f60b992e30ff kbuild: replace $(LDFLAGS) $(ldflags-y) with $(ld_flags)
2fb9279f2c3e kbuild: change ld_flags to contain LDFLAGS_$(@F)
c931d34ea085 arm64: build with baremetal linker target instead of Linux when available
5accd7f3360e kconfig: handle format string before calling conf_message_callback()
a2ff4040151a kconfig: rename file_write_dep and move it to confdata.c
0608182ad542 kconfig: split out useful helpers in confdata.c
adc18acf42a1 kconfig: remove unneeded directory generation from local*config
79123b1389cc kconfig: create directories needed for syncconfig by itself
16952b77d8b5 kconfig: make syncconfig update .config regardless of sym_change_count
d6c6ab93e17f kbuild: remove deprecated host-progs variable
56869d45e364 kconfig: fix the rule of mainmenu_stmt symbol
c151272d1687 kconfig: remove unused sym_get_env_prop() function
1880861226c1 kconfig: remove P_ENV property type
e3fd9b5384f3 scripts/dtc: consolidate include path options in Makefile
4bf6a9af0e91 kconfig: add build-only configurator targets
f1575595d156 kconfig: error out when seeing recursive dependency
5e8c5299d315 kconfig: report recursive dependency involving 'imply'
f498926c47aa kconfig: improve the recursive dependency report
98a4afbfafd2 kconfig: fix "Can't open ..." in parallel build
9a9ddcf47831 kconfig: suppress "configuration written to .config" for syncconfig
87a32e624037 kbuild: pass LDFLAGS to recordmcount.pl
d503ac531a52 kbuild: rename LDFLAGS to KBUILD_LDFLAGS
217c3e019675 disable stringop truncation warnings for now
bc8d2e20a3eb kconfig: remove a spurious self-assignment
fd65465b7016 kconfig: do not require pkg-config on make {menu,n}config
5a4630aadb9a ftrace: Build with CPPFLAGS to get -Qunused-arguments
Note that this adds new cleanup work to do in that we should adapt the
shared library support we have to what is now upstream.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.07
common:
- Align ENV_FAT_INTERFACE
- Fix MAC address source print log
- Improve based autodetection code
xilinx:
- Enable netconsole
Microblaze:
- Setup default ENV_OFFSET/ENV_SECT_SIZE
Zynq:
- Multiple DT updates/fixes
- Use DEVICE_TREE environment variable for DTB selection
- Switch to single zynq configuration
- Enable NOR flash via DM
- Minor SPL print removal
- Enable i2c mux driver
ZynqMP:
- Print multiboot register
- Enable cache commands in mini mtest
- Multiple DT updates/fixes
- Fix firmware probing when driver is not enabled
- Specify 3rd backup RAM boot mode in SPL
- Add SPL support for zcu102 v1.1 and zcu111 revA
- Redesign debug uart enabling and psu_init delay
- Enable full u-boot run from EL3
- Enable u-boot.itb generation without ATF with U-Boot in EL3
Versal:
- Enable distro default
- Enable others SPI flashes
- Enable systems without DDR
Drivers:
- Gem:
- Flush memory after freeing
- Handle mdio bus separately
- Watchdog:
- Get rid of unused global data pointer
- Enable window watchdog timer
- Serial:
- Change reinitialization logic in zynq serial driver
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
These are used in multiple places so update them to use a shared #define.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
This tool always verifies the default configuration. It is useful to be
able to verify a specific one. Add a command-line flag for this and plumb
the logic through.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
It is useful to be a little more specific about what is being checked.
Update a few messages to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Depending on the SoC, a header of four characters is prepended to the
image. There is already a macro defining the number of characters:
RK_SPL_HDR_SIZE, so use it instead of hardcoding "4".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
|
|
Introduce new configuration, CONFIG_RSA_VERIFY which will decouple building
RSA functions from FIT verification and allow for adding a RSA-based
signature verification for other file formats, in particular PE file
for UEFI secure boot.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Printing the error message in verbose mode fails, since python3
doesn't implicitely convert bytes to strings.
Signed-off-by: Markus Klotzbuecher <mk@mkio.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Commit b237d358b425 ("moveconfig: expand simple expressions") added
support for expanding expressions in configs, but used the unsafe python
built-in "eval". This patch fixes this by replacing eval with the
asteval module.
Signed-off-by: Markus Klotzbuecher <mk@mkio.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The include uboot_aes.h is not useful and
it breaks the compilation on android, so
we remove it.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reported-by: Praneeth Bajjuri <praneeth@ti.com>
|