aboutsummaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)AuthorFilesLines
2013-08-20powerpc : p1022ds : Enable p1022ds to start from eSPI with SPLYing Zhang1-7/+29
Enable p1022ds to start from eSPI with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPLYing Zhang1-7/+47
Enable p1022ds to start from eSDHC with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: mpc85xx: Support booting from SD Card with SPLYing Zhang1-0/+1
The code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some ↵Ying Zhang3-3/+0
functionality for common SPL 1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it. 2. Some functions were unused in the minimal SPL, but it is useful in the common SPL. So, enabled some functionality for common SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-19SPDX-License-Identifier: convert BSD-3-Clause filesWolfgang Denk1-21/+1
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini Don't remove some copyrights by accident] Signed-off-by: Tom Rini <trini@ti.com>
2013-08-19SPDX-License-Identifier: convert PIBS licensed filesWolfgang Denk1-24/+5
This commit adapts the files that were derived from PIBS (PowerPC Initialization and Boot Software) codeto using SPDX License Identifiers. So far, SPDX has not assigned an official License ID for the PIBS license yet, so this should be considered preliminary. Note that the following files contained incorrect license information: arch/powerpc/cpu/ppc4xx/4xx_uart.c arch/powerpc/cpu/ppc4xx/start.S arch/powerpc/include/asm/ppc440.h These files included, in addition to the GPL-2.0 / ibm-pibs dual license as inherited from PIBS, a GPL-2.0+ license header which was obviously incorrect. This has been removed. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Conflicts: Licenses/README Acked-by: Stefan Roese <sr@denx.de>
2013-08-19SPDX-License-Identifier: convert GPL-2.0+ / BSD-2-Clause dual-licensed filesWolfgang Denk1-44/+1
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-08-19net.h: don't use the reserved name __unusedJeroen Hofstee1-1/+1
The __* keywords are reserved. On FreeBSD __unused evaluates to the attribute unused, causing a compilation failure. Just use unused instead. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> cc: joe.hershberger@gmail.com
2013-08-19linkstation_HGLAN: Convert from unused CONFIG_BOOTP_MASK to specific listTom Rini1-1/+11
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-19galaxy5200: Convert from unused CONFIG_BOOTP_MASK to specific listTom Rini1-4/+3
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-19configs: Remove unused CONFIG_BOOTP_DEFAULTTom Rini18-18/+0
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-19powerpc/ppc4xx: Fix dlvision-10g reset gpioDirk Eibach1-2/+2
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
2013-08-18Merge branch 'master' of git://88.191.163.10/u-boot-armTom Rini48-1537/+1818
Fixup an easy conflict over adding the clk_get prototype and USB_OTG defines for am33xx having moved. Conflicts: arch/arm/include/asm/arch-am33xx/hardware.h Signed-off-by: Tom Rini <trini@ti.com>
2013-08-17Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD12-1018/+443
2013-08-15Add TI816X evm board supportTENART Antoine1-0/+180
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com> [trini: Change to SPDX, fix a few compiler warnings, adapt to CONFIG_OMAP_COMMON] Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15arm, da850: add ipam390 board supportHeiko Schocher1-0/+331
add the am1808 based ipam390 board from Barix. - 128MByte, DDR2, synchronous RAM 16bit databus to SDRAM interface - 128MByte, NAND Flash, 8bit databus to the NANDFlash Interface - Ethernet PHY Micrel KSZ8051R via RMII - Console on UART 0 - booting fron nand flash - spl falcon bootmode Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-08-15bootstage: get more BOOTSTAGE_ID* in show_boot_progress()Heiko Schocher1-0/+1
In case CONFIG_BOOTSTAGE is not defined, call from bootstage_mark_name() show_boot_progress(), so get more BOOTSTAGE_ID* ids in show_boot_progress() if CONFIG_BOOTSTAGE is not defined. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Tom Rini <trini@ti.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Acked-by: Simon Glass <sjg@chromium.org>
2013-08-15TI:armv7: Enable CONFIG_CMD_GPIOTom Rini1-0/+1
Add the generic "poke a GPIO" command, with the GPIO related defines. Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15TI:armv7: Enable CONFIG_CMD_SPITom Rini1-0/+1
Add the generic "poke the SPI bus" command, with the SPI related defines. Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15TI:omap5/dra7xx: Convert to ti_armv7_common.hTom Rini3-177/+34
Update omap5_common.h to use ti_armv7_common.h, and in turn update dra7xx_evm.h and omap5_uevm.h slightly. The biggest changes here are that IP blocks which exist on the platform, and had clocks enabled, now have the drivers being built as well. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15TI:am33xx: Create common config files for TI ARMv7 platforms, and AM33xxTom Rini3-218/+326
We create two new files, include/configs/ti_armv7_common.h for all of the common IP blocks and related features / commands we share in virtually all of our platforms. We then create include/configs/ti_am335x_common.h for everything common to the am335x SoC leaving just the board specific parts to include/configs/ti_am335x_common.h. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am335x_evm: Bring in 'boot_fdt' logic from i.MXTom Rini1-5/+16
Bring in the 'boot_fdt' environment variable that i.MX boards use to try and load a device tree when booting. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am335x_evm: Use default baud rate tableTom Rini1-2/+0
Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am33xx: Stop using PHYS_DRAM_1 defineTom Rini3-8/+5
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this for CONFIG_SYS_SDRAM_BASE. But then we kept on referencing PHYS_DRAM_1 in other places. Change to directly setting CONFIG_SYS_DRAM_BASE and then using that name in code. Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15am33xx: CONFIG_DMA_COHERENT defines are unused, removeTom Rini3-10/+0
Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15OMAP3: igep00x0: allow booting with a FDT from MMCJavier Martinez Canillas1-1/+12
IGEP boards now have Device Tree support in the mainline kernel. To boot an IGEP board using a DT, a uEnv.txt plain text file could be used to define a custom uenvcmd that will be run by the default boot command. It is more convenient to change the default boot command to allow loading a FDT if it is stored in the boot dir of the rootfs uSD/MMC partition. If no FDT is found then the defaul command tries to boot a zImage without a DT using legacy boot. Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
2013-08-15ARM: igep00x0.h: Enable the use of CMD_EXT4, CMD_FS_GENERIC and zImage.Enric Balletbo i Serra1-6/+7
Able to load the kernel from some form of ext[234] or FAT. Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore by default, so we should switch to use the bootz command. Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
2013-08-15ARM: IGEP0033: Remove duplicate / unused #defines.Enric Balletbo i Serra1-7/+1
As config was originally based on am335x_evm.h we have also some duplicate / unnused #defines. Commit 15191c91 removed these #defines on various AM335x boards but not for IGEP COM AQUILA. This patch simply removes them for this board. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Add support to boot from NAND.Enric Balletbo i Serra1-5/+27
Add to the default environment the possibily to boot from NAND using a ubi rootfs. Also the partition scheme is set as follows: Start Size SPL : 0x00000000 0x00080000 (512KiB) U-Boot : 0x00080000 0x00100000 (1MiB) U-Boot Env : 0x00180000 0x00020000 (128KiB) File System : 0x001C0000 - The ubiboot script gets the kernel and the dtb file from the boot directory of the File System. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Add support for Flattened Device Tree.Enric Balletbò i Serra1-20/+13
Now, the default kernel to boot the IGEP COM AQUILA is device tree based. As old kernel is deprecated we should adapt the boot commands to use DTB files. Also, with v3.9 and later of the Linux Kernel, uImage isn't builtable anymore by default, so we should switch to use the bootz command. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: IGEP0033: Remove undef of CONFIG_CMD_MEMTESTEnric Balletbo i Serra1-7/+0
After commit: 79cd2f814b1c75efd47161ac27f4cbebf768240f config_cmd_default.h: Remove CONFIG_CMD_MEMTEST It's not necessary to undef the CONFIG_CMD_MEMTEST, so we can remove it from configuration file. Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
2013-08-15ARM: AM43xx: Add config fileLokesh Vutla1-0/+135
Add config file Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15ARM: OMAP: Add CONFIG_OMAP_COMMONLokesh Vutla25-0/+25
Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-14Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini1-0/+64
2013-08-14include/fsl_usb.h: Cleanup license headerYork Sun1-17/+1
Replace license header with SPDX license identifier. Replace GPL-2.0 with GPL-2.0+. Signed-off-by: York Sun <yorksun@freescale.com> Acked-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2013-08-14fsl/usb: Move USB internal phy definitions to fsl_usb.hramneek mehresh1-0/+80
fsl_usb.h file created to share data bewteen usb platform code and usb ip driver. Internal phy structure definitions moved to this file Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-13Merge branch 'dcc' of git://www.denx.de/git/u-boot-microblazeTom Rini1-3/+0
2013-08-13Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini11-586/+1849
2013-08-13serial: arm_dcc: Remove stdio structure supportJagannadha Sutradharudu Teki1-3/+0
Removed stdio structure ops support on arm_dcc driver, and need to register with serial core so-that it can access like remianing serial drivers. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-08-12Merge branch 'master' of git://www.denx.de/git/u-boot-videoTom Rini4-6/+2166
2013-08-12powerpc/mpc85xx: Cleanup license header in source filesYork Sun3-51/+3
Fix the license header introduced by the following patches Add TWR-P10xx board support Add T4240EMU target IDT8T49N222A configuration code Add C29x SoC support Add support for C29XPCIE board Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-12edid: rename struct member to fix two EDID_* macrosChristian Gmeiner1-1/+1
Without this change EDID_DETAILED_TIMING_VSYNC_OFFSET and EDID_DETAILED_TIMING_VSYNC_PULSE_WIDTH macros can not be used (compile error). The fix is quite trivial: rename struct member to the expected name. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2013-08-12video: Add small 4x6 font from LinuxMarek Vasut2-0/+2158
This font is based on Linux drivers/video/console/font_mini_4x6.c as of commit: commit bcfbeecea11c15e243f076d37d637c2598aff4fe Author: Bjarni Ingi Gislason <bjarniig@rhi.hi.is> Date: Sun Aug 12 15:05:10 2012 +0000 drivers: console: font_: Change a glyph from "broken bar" to "vertical line" I removed these lines as they are useless in U-Boot: #include <linux/font.h> #define FONTDATAMAX 1536 Whole "const struct font_desc font_mini_4x6" block This patch also adds a new configuration option to select this smaller font, CONFIG_VIDEO_FONT_4X6 , but this is disabled by default. The default setting is the regular "large" font. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de>
2013-08-12video: Encapsulate font in video_font_data.hMarek Vasut2-5/+7
This patch moves all the font configuration values into video_font_data.h so they are all in the right place with the font. The video_font.h now only includes video_font_data.h and will allow us to select and include different font once more fonts are added. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de> [agust: fixed build warning for mcc200] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-08-12mpc5200: Misc updates to a3m071 config headerStefan Roese1-8/+23
This patch changes some features of the a3m071/a4m2k board support: - Add bootcounter support - Update MTD env default to correct values - Add mtdparts to bootargs for mtd partitioning via kernel cmdline - Added some default env variables for easy updating (kernel, dtb) - Change README to the updated flash locations Signed-off-by: Stefan Roese <sr@denx.de>
2013-08-12Merge branch 'fpga' of git://www.denx.de/git/u-boot-microblazeTom Rini1-0/+5
2013-08-12fpga: zynqpl: Add support for zc7100 device.Michal Simek1-0/+5
- Add support for zc7100 device. - FPGA programming on few of the SOC(zc7100) takes more than 1sec, hence increased the program time by 4sec to sync' all soc's. Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-08-09powerpc/c29xpcie: add support for C29XPCIE boardMingkai Hu1-0/+472
C29XPCIE board is a series of Freescale PCIe add-in cards to perform as public key crypto accelerator or secure key management module. It includes C293PCIE board, C293PCIE board and C291PCIE board. - 512KB platform SRAM in addition to 512K L2 Cache/SRAM - 512MB soldered DDR3 32bit memory - CPLD System Logic - 64MB x16 NOR flash and 4GB x8 NAND flash - 16MB SPI flash Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Singed-off-by: Po Liu <Po.Liu@freescale.com> [yorksun: Fixup include/configs/C29XPCIE.h] Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/pcie: add PCIe version 3.x supportZang Roy-R619111-7/+0
T4240 PCIe IP is version 3.0 and has some update comparing previous QorIQ products. 1. Move Freescale specific register define to arch/powerpc/include/asm/fsl_pci.h and update the register offset define for T4240. 2. add the status/control register define use status/control register to judge the link status 3. The original code uses 'Programming Interface' field to judge if PCIE is EP or RC mode, however, T4240 does not support this functionality. According to PCIE specification, 'Header Type' offset 0x0e is used to indicate header type, so for PCIE controller, the patch changes code to use 'Header Type' field to identify if the PCIE is RC or EP mode. This patch fixes the PCIe card link up issue on T4240QDS. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09powerpc/rman: fix RMan support for t4240 and b4860Minghuan Lian3-0/+4
1. Add CONFIG_SYS_DPAA_RMAN macro to t4240 and b4860. 2. Decrease RMan liodn offset number. SET_RMAN_LIODN() is used to set liodn offset of RMan blocks 0-3. For t4240 and b4860, RMan liodn base is assigned to 922, the original offset number is too large that the liodn (base+offset 922+678 = 1600) is greater than 0x500 the maximum liodn number. Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com>
generated by cgit v1.1 at 2024-10-31 11:35:09 +0000