aboutsummaryrefslogtreecommitdiff
path: root/include/mmc.h
AgeCommit message (Collapse)AuthorFilesLines
2019-10-10mmc: add a driver callback for power-cycleYann Gautier1-0/+13
Some MMC peripherals require specific power cycle sequence, where some registers need to be written between the regulator is turned off and then back on. This is the case for the MMC IP embedded in STM32MP1 SoC. In STM32MP157 reference manual [1], the power cycle sequence is: 1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset the SDMMC to the reset state and the CPSM and DPSM to the Idle state. 2. Disable the Vcc power to the card. 3. Set the SDMMC in power-cycle state. This will make that the SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card from being supplied through the signal lines. 4. After minimum 1ms enable the Vcc power to the card. 5. After the power ramp period set the SDMMC to the power-off state for minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to drive “1”. 6. After the 1ms delay set the SDMMC to power-on state in which the SDMMC_CK clock will be enabled. 7. After 74 SDMMC_CK cycles the first command can be sent to the card. The step 3. cannot be handled by the current framework implementation. A new callback (host_power_cycle) is created, and called in mmc_power_cycle(), after mmc_power_off(). The incorrect power cycle sequence has shown some boot failures on STM32MP1 with some SD-cards, especially on cold boots when the input frequency is low (<= 25MHz). Those failures are no more seen with this correct power cycle sequence. [1] https://www.st.com/resource/en/reference_manual/DM00327659.pdf Signed-off-by: Yann Gautier <yann.gautier@st.com>
2019-10-10spl: dm_mmc: Initialize only the required mmc deviceLokesh Vutla1-0/+1
In SPL, all the available mmc devices gets initialized during boot. This might not work in cases where clocks are not available for certain mmc devices(other than boot device) and the support for enabling device might not be ready. Texas Instruments' K3 J721E device having a central system controller (dmsc) is one such example falling in this category. Below is the sequence for the failing scenario: - ROM comes up in SD mode and loads SPL by just initialing SD card. - SPL loads dmsc firmware from SD Card. Since ROM has enabled SD, SPL need not enable the SD, just need to re initialize the card. But SPL is trying to initialize other MMC instances which are in disabled state. Since dmsc firmware is not yet available, devices cannot be enabled. So in SPL, initialize only the mmc device that is needed. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-09-05mmc: Rename timeout parameters for clarificationSam Protsenko1-6/+6
It's quite hard to figure out time units for various function that have timeout parameters. This leads to possible errors when one forgets to convert ms to us, for example. Let's rename those parameters correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues further. While at it, add time units info as comments to struct mmc fields. This commit doesn't change the behavior, only renames parameters names. Buildman should report no changes at all. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
2019-07-15mmc: support hs400 enhanced strobe modePeng Fan1-0/+15
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for tuning procedure. The flow is as following: - set HS_TIMIMG (Highspeed) - Host change freq to <= 52Mhz - set the bus width to Enhanced strobe and DDR8Bit(CMD6), EXT_CSD[183] = 0x86 instead of 0x80 - set HS_TIMING to 0x3 (HS400) - Host change freq to <= 200Mhz - Host select HS400 enhanced strobe complete Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15cmd: Remove mmc_spi commandAnup Patel1-1/+0
The mmc_spi command was added to manually setup MMC over SPI bus using command. This was required by the legacy non-DM MMC_SPI driver. With DM based MMC_SPI driver in-place, we can now use all general storge commands and mmc command for MMC over SPI bus hence we remove the mmc_spi command all it's references. Suggested-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15mmc: When switching partition, use the timeout specified in the ext_csdJean-Jacques Hiblot1-0/+5
The e-MMC spec allows the e-MMC to specify a timeout for the partition switch command. It can take up to 2550 ms. There is no lower limit to this value in the spec, but do as the the linux driver does and force it to be at least 300ms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: use the generic timeout for cmd6 (SWITCH) provided in the ext_csdJean-Jacques Hiblot1-0/+2
Starting with rev 4.5, the eMMC can define a generic timeout for the SWITCH command. Following Linux Kernel code, the timeout also changed from 1000 -> 500 Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: if possible, poll the busy state using DAT0Jean-Jacques Hiblot1-2/+0
Using the DAT0 line as a rdy/busy line is an alternative to reading the status register of the card. It especially useful in situation where the bus is not in a good shape, like when modes are switched. This is also how the linux driver behaves. Note of warning: As per the specification, while polling on DAT0 the CLK must not turned off: "[...] Without a clock edge the Device (unless previously disconnected by a deselect command (CMD7)) will force the DAT0 line down, forever. [...]" Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15Revert "mmc: Add a new callback function to perform the 74 clocks cycle ↵Jean-Jacques Hiblot1-10/+0
sequence" This reverts commit 318a7a576bc49aa8b4207e694d3fbd48c663d6ac. The last and only user of this callback had been the omap_hsmmc driver. It is not used anymore. Removing the callback. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: Read sd card detect properties from DTT Karthik Reddy1-0/+4
This patch reads card detect properties from device tree & added mmc capability macros in mmc.h. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-16mmc: Downgrade SD/MMC from UHS/HS200/HS400 modes before bootMarek Vasut1-0/+6
Older kernel versions or systems which do not connect eMMC reset line properly may not be able to handle situations where either the eMMC is left in HS200/HS400 mode or SD card in UHS modes by the bootloader and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card to non-UHS mode before booting the kernel to allow such older kernels to work with modern U-Boot. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
2019-01-17env: fix allow to build multiple environmentsRajesh Bhagat1-0/+3
Patch fixes build error when enabling CONFIG_ENV_IS_IN_SPI_FLAS and CONFIG_ENV_IS_IN_MMC at the same time mentioned issue in below link: Refer: https://lists.denx.de/pipermail/u-boot/2018-February/319565.html build error when enabling CONFIG_ENV_IS_IN_SPI_FLASH and CONFIG_ENV_IS_IN_MMC at the same time. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-10-07mmc: rpmb: add mmc_rpmb_route_frames()Jens Wiklander1-0/+19
Adds mmc_rpmb_route_frames() to route RPMB data frames from/to an external entity. Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-10mmc: add HS400 supportPeng Fan1-0/+11
Add HS400 support. Selecting HS400 needs first select HS200 according to spec, so use a dedicated function for HS400. Add HS400 related macros. Remove the restriction of only using the low 6 bits of EXT_CSD_CARD_TYPE, using all the 8 bits. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-07-23mmc: break out get_op_cond code to its own functionJon Nettleton1-0/+10
This code is useful for testing the existance of devices that do not have card detect capabilities. This breaks out the core functionality and leaves the actual init logic and error reporting in mmc_start_init(). Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-07-23mmc: drop mention of IN_PROGRESS statusBaruch Siach1-1/+1
The IN_PROGRESS macro has been removed in commit bd47c13583f (mmc: Fix splitting device initialization). Remove it from the mmc_start_init() function description. Signed-off-by: Baruch Siach <baruch@tkos.co.il>
2018-05-08mmc: add the MMC_CLK_ENABLE/DISABLE macro in mmc.hJaehoon Chung1-0/+3
mmc_set_clock() function has the disable argument as bool type. When mmc_set_clock is called, it might be passed to "true" or "false". But it's too confusion whether clock is enabled or disabled with only "true" and "false". To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from true/false. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini1-2/+1
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-19mmc: fix bug in mmc_startup_v4()Jean-Jacques Hiblot1-0/+1
The correspondence between mmc versions as used in u-boot and the version numbers reported in register EXT_CSD_REV is wrong for versions above and including MMC_VERSION_4_41. All those versions were shifted by one: real 4.5 hardware appeared to be MMC_VERSION_5_0. Fix this by adding the missing version in the correspondence table. Reported-by: eil Eilmsteiner Heribert <eil@keba.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2018-01-12mmc: remove hc_wp_grp_size from struct mmc if not neededJean-Jacques Hiblot1-0/+2
hc_wp_grp_size is needed only if hardware partitionning is used. On ARM removing it saves about 30 bytes of code space. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: don't read the size of eMMC enhanced user data area in SPLJean-Jacques Hiblot1-0/+2
This information is only used by the "mmc info" command. On ARM removing this information from SPL saves about 140 of code space. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: compile out erase and write mmc commands if write operations are not ↵Jean-Jacques Hiblot1-0/+2
enabled Also remove erase_grp_size and write_bl_len from struct mmc as they are not used anymore. On ARM, removing them saves about 100 bytes of code space in SPL. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: read ssr only if MMC write support is enabledJean-Jacques Hiblot1-0/+2
The content of ssr is useful only for erase operations. on ARM, removing sd_read_ssr() saves around 300 bytes. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: make UHS and HS200 optionalJean-Jacques Hiblot1-4/+23
Supporting USH and HS200 increases the code size as it brings in IO voltage control, tuning and fatter data structures. Use Kconfig configuration to select which of those features should be built in. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12dm: mmc: update mmc_of_parse()Jean-Jacques Hiblot1-1/+10
* convert to livetree API * don't fail because of an invalid bus-width, instead default to 1-bit. * recognize 1.2v DDR and 1.2v HS200 flags Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12dm: mmc: Add a library function to parse generic dt bindingKishon Vijay Abraham I1-0/+1
Add a new function to parse host controller dt node and set mmc_config. This function can be used by mmc controller drivers to set the generic mmc_config. This function can be extended to set other UHS mode caps once UHS mode support is added. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: add a library function to send tuning commandJean-Jacques Hiblot1-0/+1
HS200/SDR104 requires tuning command to be sent to the card. Add a simple function to send tuning command and to read and compare the received data with the tuning block pattern. This function can be used by platform driver to perform DLL tuning. This patch is similar to commit 996903de92f0 ("mmc: core: add core-level function for sending tuning commands") added in linux kernel. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: use the right voltage level for MMC DDR and HS200 modesJean-Jacques Hiblot1-3/+17
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v or 1.2v signal voltages. Select the lowest voltage available when using those modes. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Retry some MMC cmds on failureKishon Vijay Abraham I1-0/+4
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time as done in Linux kernel. Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first attempt, therefore retry this cmd a few times as done in kernel. To make it clear that those are optionnal workarounds, a new Kconfig option 'MMC_QUIRKS' is added (enabled by default). Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Change mode when switching to a boot partitionJean-Jacques Hiblot1-1/+6
Boot partitions do not support HS200. Changing to a lower performance mode is required to access them. mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to make it easier to call them outside of the initialization context. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: disable UHS modes if Vcc cannot be switched on and offJean-Jacques Hiblot1-0/+1
If a power cycle cannot be done on Vcc, it is safer not to try the UHS modes because we wouldn't be able to recover from an error occurring during the UHS initialization. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Add support for UHS modesJean-Jacques Hiblot1-1/+39
Add UHS modes to the list of supported modes, get the UHS capabilites of the SDcard and implement the procedure to switch the voltage (UHS modes use 1v8 IO lines) During the voltage switch procedure, DAT0 is used by the card to signal when it's ready. The optional card_busy() callback can be used to get this information from the host driver. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: add HS200 support in MMC coreKishon Vijay Abraham I1-0/+18
Add HS200 to the list of supported modes and introduce tuning in the MMC startup process. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: Add a execute_tuning() callback to the mmc operations.Kishon Vijay Abraham I1-0/+11
Tuning is a mandatory step in the initialization of SDR104 and HS200 modes. This callback execute the tuning process. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: add a new mmc parameter to disable mmc clockKishon Vijay Abraham I1-1/+11
mmc clock has to be disabled in certain cases like during the voltage switch sequence. Modify mmc_set_clock function to take disable as an argument that signifies if the clock has to be enabled or disabled. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Add a new callback function to perform the 74 clocks cycle sequenceJean-Jacques Hiblot1-0/+10
Add a new callback function *send_init_stream* which start a sequence of at least 74 clock cycles. The mmc core uses *mmc_send_init_stream* in order to invoke the callback function. This will be used during power cycle where the specification requires such a sequence after power up. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: Enable signal voltage to be selected from mmc coreKishon Vijay Abraham I1-0/+8
Add a new function *mmc_set_signal_voltage* in mmc core which can be used during mmc initialization to select the signal voltage. Platform driver should use the set_ios callback function to select the signal voltage. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: make mmc_set_ios() return statusKishon Vijay Abraham I1-1/+1
set_ios callback has a return value of 'int' but the mmc_set_ios() function ignore this. Modify mmc_set_ios() and the callers of mmc_set_ios() to to return the error status. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: refactor MMC startup to make it easier to support new modesJean-Jacques Hiblot1-0/+11
The MMC startup process currently handles 4 modes. To make it easier to add support for more modes, let's make the process more generic and use a list of the modes to try. The major functional change is that when a mode fails we try the next one. Not all modes are tried, only those supported by the card and the host. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: refactor SD startup to make it easier to support new modesJean-Jacques Hiblot1-0/+1
The SDcard startup process currently handles only 2 modes. To make it easier to add support for more modes, let's make the process more generic and use a list of the modes to try. The major functional change is that when a mode fails we try the next one. Not all modes are tried, only those supported by the card and the host. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: Add a function to dump the mmc capabilitiesJean-Jacques Hiblot1-0/+1
This adds a simple helper function to display information (bus width and mode) based on a capability mask. Useful for debug. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12mmc: introduce mmc modesJean-Jacques Hiblot1-6/+29
no functionnal changes. In order to add the support for the high speed SD and MMC modes, it is useful to track this information. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: make ext_csd part of struct mmcJean-Jacques Hiblot1-0/+1
The ext csd is used for comparison many times. Keep a reference content of the ext csd in the struct mmc to avoid reading multiple times Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-12mmc: dm: get the IO-line and main voltage regulators from the dtsJean-Jacques Hiblot1-0/+4
Get a reference to the regulator devices from the dts and store them in the struct mmc for later use. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-08-17cmd: mmc: add mmc partconf read capabilityAngelo Dureghello1-0/+4
This patch allows to show the EXT_CSD[179] partition_config register info, just by specifying the dev param: U-Boot> mmc partconf 0 EXT_CSD[179], PARTITION_CONFIG: BOOT_ACK: 0x0 BOOT_PARTITION_ENABLE: 0x0 PARTITION_ACCESS: 0x0 Signed-off-by: Angelo Dureghello <angelo@sysam.it> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2017-08-17dm: mmc: Drop CONFIG_DM_MMC_OPSSimon Glass1-3/+3
All boards which use DM_MMC have now been converted to use DM_MMC_OPS. Drop the option and good riddance. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-01Merge git://git.denx.de/u-boot-x86Tom Rini1-12/+0
2017-08-01x86: Convert MMC to driver modelSimon Glass1-12/+0
Convert the pci_mmc driver over to driver model and migrate all x86 boards that use it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> [bmeng: remove DM_MMC from edison_defconfig] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2017-08-01dm: mmc: Allow disabling driver model in SPLSimon Glass1-6/+6
At present if U-Boot proper uses driver model for MMC, then SPL has to also. While this is desirable, it places a significant barrier to moving to driver model in some cases. For example, with a space-constrained SPL it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves adjusting some drivers. Add new SPL versions of the options for DM_MMC, DM_MMC_OPS and BLK. By default these follow their non-SPL versions, but this can be changed by boards which need it. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-27Revert "x86: Convert MMC to driver model"Bin Meng1-0/+12
This reverts commit ddb3ac3c716f56cead695444e65a7ba7b0946555. With MMC converted to driver model, SCSI driver is broken due to zero address access at (ops->read) in block_dread() function. The fix (SCSI driver converted to DM) is ready in u-boot-dm branch, but it is too late for this relese to get that in. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-07-15 03:01:18 +0000