aboutsummaryrefslogtreecommitdiff
path: root/include/configs
AgeCommit message (Collapse)AuthorFilesLines
2014-02-22ARM: rpi_b: rework boot scripts, enable sysbootStephen Warren1-15/+70
Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as much as possible. This will aid in a future patch which will create a common header e.g. config_distro_bootcmd.h. While at it, enable booting from extlinux.conf using the sysboot command. The iteration and componentization currently makes a little more sense for Tegra than RPi, but I'd still like to keep the two as similar as possible. USB and networking support is coming to the RPi in due course, and it'll all make more sense then anyway. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-21ARM: rpi_b: load /uEnv.txt from MMC at startupStephen Warren1-0/+5
The Pi has no flash to store an environment in the usual fashion. However, the user may wish to customize the environment. We know that the SD card must be present, since that's where the boot ROM has loaded U-Boot from. So, load uEnv.txt from there early during boot. This allows the user to e.g. customize boot_targets, in order to automatically select network boot. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-21ARM: rpi_b: convert to use distro defaultsStephen Warren1-16/+13
Modify the rpi_b board to include the "distro defaults" header, so that all the config options distros expect are enabled. Remove any #defines that enable the same options from the rpi_b.h. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-20Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD44-248/+9
Conflicts: Makefile drivers/net/npe/Makefile These two conflicts arise from commit 0b2d3f20 ("ARM: NET: Remove the IXP NPE ethernet driver") and are resolved by deleting the drivers/net/npe/Makefile file and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-19configs: Delete unused CONFIG_SYS_64BIT_{VSPRINTF, STRTOUL}Masahiro Yamada4-6/+0
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19configs: Delete obsolete macro, CONFIG_SYS_GBL_DATA_SIZEMasahiro Yamada25-51/+8
CONFIG_SYS_GBL_DATA_SIZE is not used any more. The size of struct "global_data" is automatically calculated by asm-offsets. (See lib/asm-offsets.c) GENERATED_GBL_DATA_SIZE should be used instead of CONFIG_SYS_GBL_DATA_SIZE. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19config: remove platform CONFIG_SYS_HZ definition part 3Masahiro Yamada17-21/+0
This commit removes platform CONFIG_SYS_HZ definition for the remainders of part1 (commit cdb23792) and part2 (commit f232950f). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Rob Herring <rob.herring@calxeda.com>
2014-02-19mini2440.h: Delete remainder of dead boardMasahiro Yamada1-170/+0
Commit af5b9b1f removed mini2440 board support, but missed to delete include/configs/mini2440.h. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19sandbox: enable CONFIG_CMD_FS_GENERICStephen Warren1-0/+1
Since the generic ls command no longer segfaults sandbox, enable it. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-02-19Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD14-104/+122
2014-02-19zynq: Add support for U-BOOT SPLMichal Simek1-0/+77
SPL is using ps7_init.c/h files which are generated from design tools which have to be copied to boards/xilinx/zynq folder before compilation. BSS section is moved to SDRAM because fat support requires more space than SRAM size. Added: - MMC and QSPI support - Boot OS directly from SPL - Enable SPL command Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-02-19zynq: Implement dump clock commandSoren Brinkmann1-0/+1
Enable and implement dump clock command which shows soc frequencies. Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19zynq: Provide a framework to read clock frequenciesSoren Brinkmann1-0/+1
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19zynq: serial: Simplify serial driver initializationMichal Simek1-17/+2
Define both serial uarts in the driver and return default uart based on board configuration. - Move baseaddresses to hardware.h - Define default baudrate and clock values Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19zynq: Enable tftp put commandMichal Simek1-0/+1
For saving content of memory via tftp to file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19zynq: Extend kernel image size to 20MBMichal Simek1-0/+3
Extend max kernel image size. Gunzip is checking this value. If kernel is larger, message below is shown. Uncompressing Kernel Image ... Error: inflate() returned -5 GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19zynq: Fix incorrect header nameMichal Simek2-2/+2
Zynq common configuration is placed in zynq-common.h not zynq_common.h. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'Albert ARIBAUD5-1063/+0
2014-02-17Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini27-239/+456
2014-02-17Merge branch 'master' of git://git.denx.de/u-boot-mmcTom Rini2-0/+3
2014-02-13arm/km: introduce kmsugp1 targetGerlando Falauto1-2/+10
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA. The only difference is that the PCIe reset is connected to Kirkwood pin MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7. Such pin should theoretically be handled by the PCIe subsystem automatically, but this turned out not to be the case. So simply configure this PIN as a GPIO and issue a pulse manually. Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com> Cc: Valentin Longchamp <valenting.longchamp@keymile.com> Cc: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: define fdt_high env variable and allow backwards compatibilityGerlando Falauto4-2/+5
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high" This is necessary on Kirkwood so that the FDT does not get relocated above the memory limit that the kernel cannot access (that is the memory part reserved for the switch). This was tested on NUSA1, where it is necessary, and on ETER1, where it doesn't seem to hurt. We want the scripts to also work with older versions of u-boot, where: a) set_fdthigh is not defined (will be default env for newer u-boots) b) the fdt will not be available For this reason, we use "set_fdthigh" to tell whether we are running a newer (FDT-aware) u-boot or not. So if "set_fdthigh" runs successfully or arch != arm we try loading the fdt; otherwise we proceed normally. Notice how, contrary to release mode, set_fdthigh will _not_ be part of subbootcmds for develop and ramfs, but will be executed as part of "tftpfdt". Since this is only needed for kirkwood cards, and it prevents the kernel from booting on QorIQ (though it seemed to work on ETER1), we change its definition in the default env for powerpc so that the value is only set on ARM. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: enable FDT for km_kirwkoodGerlando Falauto3-8/+10
This consists of: a) Defining the addresses, enabling fdtsupport [arm] b) Defining "cramfsloadfdt" [arm,powerpc => common] c) Adding the FDT address to bootm [arm,powerpc => common] d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common] This should work with 3.10 kernels, whether loaded through TFTP (with rootfs either through NFS or TFTP-ramfs) or from the NAND. The machid was left unchanged, this should keep compatibility with both older and newer kernels. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km: add CONFIG_KM_BOARD_EXTRA_ENV to default environmentHolger Brunck1-0/+5
This is needed for board specific additional environment variables. E.g. the mgcoge3un has this additional "waitforne" variable. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13arm/km/suv31: switch to 256MB RAMHolger Brunck1-0/+3
We now use 256MB RAM instead of 128MB. We can use the same config file as kmnusa. Signed-off-by: Holger Brunck <holger.brunck@keymile.com> Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13zynq: Fix elf header generationMichal Simek1-0/+2
This patch is here because of: "arm: keep all sections in ELF file" (sha1: 47ed5dd031d7d2c587e6afd386e79ccec1a1b7f7) Our tools expect to have elf with only LOAD header. Without this fix also PHDR, INTERP and DYNAMIC headers are available in ELF. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-13zynq: Use full tftpboot command instead of shortcut tftpMichal Simek1-1/+1
The reason is enabling tftpput command where tftp shorcut stops to work for tftpboot. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-13ARM: rpi_b: set $fdtfile in default environmentStephen Warren1-0/+1
U-Boot names the Raspberry Pi board rpi_b. This means that the common expression for DTB filename ${soc}-${board}.dtb expands to bcm2835-rpi_b.dtb. However, the DTB generated by the Linux kernel is bcm2835-rpi-b.dtb. Set $fdtfile in U-Boot's environment so that scripts look for the correct DTB filename. An alternative would be to rename the U-Boot board to rpi-b. However, that change would be far more invasive, and end up affecting users (i.e they'd have to change their U-Boot build commands). Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-13Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'Albert ARIBAUD4-25/+128
2014-02-11Merge branch 'master' of git://git.denx.de/u-boot-armStefano Babic224-2032/+470
2014-02-11mx6: Enable L2 cache supportFabio Estevam1-0/+5
Add L2 cache support and enable it by default. Configure the L2 cache in the same way as done by FSL kernel: http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Dirk Behme <dirk.behme@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-02-11mx6sl: Adjust fdt_addr to avoid address overlappingFabio Estevam1-1/+1
Similarly as it was done on commit 6584a1b526 (ARM: mx6: Change the FDT loading address to avoid overlaping), we need to adjust the fdt_addr in order to be able to boot FSL 3.10 kernel. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11vf610twr: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11udoo: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx6slevk: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx6sabre_common: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx6qarm2: Set default environment to use zImageOtavio Salvador1-5/+5
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx53loco: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx51evk: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx28evk: Set default environment to use zImageOtavio Salvador1-13/+13
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11mx23evk: Set default environment to use zImageOtavio Salvador1-6/+6
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11hummingboard: Set default environment to use zImageOtavio Salvador1-10/+10
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11cgtqmx6eval: Set default environment to use zImageOtavio Salvador1-7/+7
Change the default environment to use zImage instead of uImage, this requires changes to the default environment to load a file named zImage instead of uImage, and to use the 'bootz' command instead of 'bootm' when booting the kernel. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-07dra7xx_evm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini1-0/+2
Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07omap5_uevm: Add CONFIG_SUPPORT_EMMC_BOOT, document usageTom Rini1-0/+1
Add a README to the board which lists the commands required to enable booting from the eMMC boot partitions found on the board. Signed-off-by: Tom Rini <trini@ti.com> Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07x600: Switch to CONFIG_PHYLIBTom Rini1-2/+1
Now that the designware ethernet driver uses phylib we need to turn it on here. Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2014-02-07net/designware - switch driver to phylib usageAlexey Brodkin3-4/+6
With this change driver will benefit from existing phylib and thus custom phy functionality implemented in the driver will go away: * Instantiation of the driver is now much shorter - 2 parameters instead of 4. * Simplified phy management/functoinality in driver is replaced with rich functionality of phylib. * Support of custom phy initialization is now done with existing "board_phy_config". Note that after this change some previously used config options (driver-specific PHY configuration) will be obsolete and they are simply substituted with similar options of phylib. For example: * CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled by default. * CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise automatically the first discovered on MDIO bus phy will be used I believe there's no need now in "doc/README.designware_eth" because user only needs to instantiate the driver with "designware_initialize" whose prototype exists in "include/netdev.h". Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Vipin Kumar <vipin.kumar@st.com> Cc: Stefan Roese <sr@denx.de> Cc: Mischa Jonker <mjonker@synopsys.com> Cc: Shiraz Hashim <shiraz.hashim@st.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Amit Virdi <amit.virdi@st.com> Cc: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-07arc: add AXS101 board supportAlexey Brodkin1-0/+181
AXS101 is a new generation of devlopment boards from Synopsys that houses ASIC with ARC700 and lots of DesignWare peripherals: * DW APB UART * DW Mobile Storage (MMC/SD) * DW I2C * DW GMAC Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-02-07arc: add Arcangel4 board supportAlexey Brodkin2-0/+183
Arcangel4 is a FPGA-based development board that is used for prototyping and verificationof of both ARC hardware (CPUs) and software running upon CPU. This board avaialble in 2 flavours: * Little-endian (arcangel4) * Big-endian (arcangel4-be) Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Vineet Gupta <vgupta@synopsys.com> Cc: Francois Bedard <fbedard@synopsys.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-02-07board:samsung:trats/trats2: enable boot with appended and separated DTBPiotr Wilczek2-6/+12
This patch modifies envs to enable dual kernel boot - with separated DTB if the DTB file is loaded successfully; - with DTB apppended to uImage if DTB file is not found; This is neccesssary for backward compatibilty. Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
generated by cgit v1.1 at 2024-07-14 21:40:50 +0000