aboutsummaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2021-02-04mmc: am654_sdhci: Use sdhci_set_control_reg()Faiz Abbas1-16/+2
Use the generic sdhci_set_control_reg() instead of duplicating in platform driver. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Fix HISPD bit configuration in some lower speed modesFaiz Abbas2-2/+24
According to the AM654x Data Manual[1], the setup timing in lower speed modes can only be met if the controller uses a falling edge data launch. To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25 speed modes. Use the sdhci writeb callback to implement this condition. [1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for software tuningFaiz Abbas1-0/+45
With the new SW tuning App note[1], a custom tuning algorithm is required for eMMC HS200, HS400 and SD card UHS modes. The algorithm involves running through the 32 possible input tap delay values and sending the appropriate tuning command (CMD19/21) for each of them to get a fail or pass result for each of the values. Typically, the range will have a small contiguous failing window. Considering the tuning range as a circular buffer, the algorithm then sets a final tuned value directly opposite to the failing window. [1] https://www.ti.com/lit/pdf/spract9 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for writing to clkbuf_selFaiz Abbas1-0/+11
Add support for writing new clock buffer select property for both the am654x and j721e 4 bit IPs Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for input tap delayFaiz Abbas1-80/+161
DLL need only be enabled for speed modes and clock frequencies at or above 50 MHz. For speed modes that don't enable the DLL, we need to configure a static input delay value. This involves reading an optional itap-del-sel-* value from the device tree and configuring it for the appropriate speed mode. Therefore, move all dll configurations to their own functions and gate it with 50 MHz speed and a minimum mode. If both these conditions are not satisfied then configure delay chain modes. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add support for AM65x SR2.0Faiz Abbas1-0/+30
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup the platform data and do DLL calibration if the revision is 1.0 Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Add flag for PHY calibrationFaiz Abbas1-12/+14
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB flag to indicate the same. Also move the write of trm_icp and driver strength to the set_clock() function to match the kernel configuration flow. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Convert flag fields to BIT macroFaiz Abbas1-4/+4
Convert the flags field defines to use the BIT() macro. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: am654_sdhci: Unconditionally switch off DLL in the beginning of ios_post()Faiz Abbas1-9/+1
There are some speed modes that work without switching the dll on. Unconditionally switch off the DLL before setting clock frequency to support this case. The software will automatically enable DLL for speed modes that require it. This also means the dll_on priv data member is no longer required. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04mmc: sdhci: Add helper functions for UHS modesFaiz Abbas1-0/+95
Add a set_voltage() function which handles the switch from 3.3V to 1.8V for SD card UHS modes. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04remoteproc: k3_r5: Sync to upstreamed kernel DT property namesSuman Anna1-4/+4
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the equivalent remoteproc driver in the Linux kernel. Some of the DT properties used in U-Boot got upstreamed using different names in Linux kernel. The modified property names include the R5F cluster mode configuration property "lockstep-mode"; and three different individual R5F core config properties - "atcm-enable", "btcm-enable" and "loczrama". The property names were updated as follows: lockstep-mode => ti,cluster-mode atcm-enable => ti,atcm-enable btcm-enable => ti,btcm-enable loczrama => ti,loczrama Update the K3 R5F remoteproc driver, the corresponding binding, and all the existing usage in AM65x, J721E and J7200 dts files all at once to use the new properties and to not break any bisectability. Signed-off-by: Suman Anna <s-anna@ti.com>
2021-02-01Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86WIP/01Feb2021Tom Rini1-1/+1
- Fix CMD_ACPI dependency in Kconfig - Correct overflow in __udelay() in TSC timer driver - Add a devicetree node for eMMC for Coral - Minor improvements on image loading - Reduce size of Samus image
2021-02-01x86: tsc_timer: Correct overflow in __udelay()Simon Glass1-1/+1
At present long delays such as msleep(2000) can cause an overflow in this function. There is no need for this, since it already uses a 64-bit int. Add a cast to correct this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2021-01-31Merge https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiWIP/31Jan2021Tom Rini2-30/+37
- Allwinner H616 Ethernet support - sunxi ata debug fix
2021-01-31ata: sunxi: fix debug messagesDario Binacchi1-4/+4
It is useless and misleading to print the ret variable that is not set by the dev_read_addr routine. Also, move the '\n' character after the round bracket that contains the error code. Signed-off-by: Dario Binacchi <dariobin@libero.it> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-31net: sun8i-emac: Determine pinmux based on SoC, not EMAC typeAndre Przywara1-8/+20
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is not dependent on the EMAC IP, but on the SoC it is integrated in. Deriving the pinmux from the DT compatible string (as we do at the moment) will thus cause problems with certain EMAC IP / SoC combinations. To avoid this exact issue with the H616, let's use our Kconfig MACH symbols to choose the correct pinmux setup. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-31net: sun8i-emac: Always clear syscon EPHY registerAndre Przywara1-18/+13
At the moment we only consider the EPHY register for those SoCs were we actually have an internal PHY to configure. However even other SoCs have this register, an expect the EPHY select bit to be cleared for proper operation with an external PHY. Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC model, and clear the H3_EPHY_SELECT bit if no internal PHY is used. We get away without it so far because SoCs like the A64 clear this bit on reset, but we need to explicitly clear it on the H616, for instance. The Linux driver does so as well. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Jernej Skrabec <jernej.skrabec@siol.net> Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
2021-01-31Merge https://gitlab.denx.de/u-boot/custodians/u-boot-usbTom Rini15-162/+692
- Assorted gadget changes including: - dfu: Fix handling of UBI partitions in MTD backend - gadget: f_thor: fix wrong file size cast - Extend cmd: bcb - Fixes for fastboot and rockchip gadgets - dfu: Add SCRIPT and SKIP entities - dfu/thor: Add `dfu_alt_info` reinitialization from flashed script - u-boot: Reduce size of u-boot as usbd_device_* arrays are not exported
2021-01-31Merge https://gitlab.denx.de/u-boot/custodians/u-boot-shTom Rini3-0/+8
- Sync r8a774a1 DT files, tmio sdhi DMA fix
2021-01-31usb: gaget: ci: set ep's desc when enable epLi Jun1-0/+2
As we need standard usb_ep's desc, so set it when enable ep. Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: fastboot: use correct max packet sizeLi Jun1-1/+1
Change to use wMaxPacketSize of current speed EP desc for request length wrap up. Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: udc: ci: update speed handlingLi Jun1-2/+1
Remove the gadget driver speed check, and set its max_speed to be USB_SPEED_HIGH. Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Tested-by: faqiang.zhu <faqiang.zhu@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: composite: force gadget to be USB2 for HS only functionLi Jun1-0/+13
If one of functions is not super speed capable, we need force the udc to be high speed, this is an equivalent implementation of usb_gadget_udc_set_speed() in kernel but simple, which set the gadget max_speed to be high speed, so afterwards when start gadget duc can set the HW to be USB 2.0 mode. Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Tested-by: faqiang.zhu <faqiang.zhu@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: dnl: set dnl to be super speedLi Jun1-0/+1
Set its max_speed to be super speed. Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Tested-by: faqiang.zhu <faqiang.zhu@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: fastboot: add super speed supportLi Jun1-3/+44
Add super speed EP config. Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Tested-by: faqiang.zhu <faqiang.zhu@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: add super speed supportLi Jun1-25/+60
This patch is to add usb gadget super speed support in common driver, including BOS descriptor and select the super speed descriptor from function driver. Reviewed-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Tested-by: faqiang.zhu <faqiang.zhu@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: update os_desc_config when add configJun Li1-2/+2
Always use the new added config for os_desc_config to fix cdev-> os_desc_config may miss set in case we restart usb gadget driver. Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: set correct usb_configuration for os_desc_configJun Li1-7/+3
The current way to set cdev->os_desc_config is wrong if user restart fastboot, as the old config is not used anymore and new allocated usb_configuration will be used, so set the os_desc_config while usb_add_config. Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: fastboot: add ext properties for WCIDLi Jun1-0/+34
Add device interface GUID for Microsoft Extended Properties Feature Descriptor. Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: add WCID support for mfgtoolLi Jun1-0/+20
Enable WCID(Microsoft Compatible ID Feature Descriptor) for mfgtool. Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: OS Feature Descriptors supportLi Jun2-1/+374
This is a proting patch from linux kernel: 37a3a533429e ("usb: gadget: OS Feature Descriptors support"), the original commit log see below: There is a custom (non-USB IF) extension to the USB standard: http://msdn.microsoft.com/library/windows/hardware/gg463182 They grant permission to use the specification - there is "Microsoft OS Descriptor Specification License Agreement" under the link mentioned above, and its Section 2 "Grant of License", letter (b) reads: "Patent license. Microsoft hereby grants to You a nonexclusive, royalty-free, nontransferable, worldwide license under Microsoft鈥檚 patents embodied solely within the Specification and that are owned or licensable by Microsoft to make, use, import, offer to sell, sell and distribute directly or indirectly to Your Licensees Your Implementation. You may sublicense this patent license to Your Licensees under the same terms and conditions." The said extension is maintained by Microsoft for Microsoft. Yet it is fairly common for various devices to use it, and a popular proprietary operating system expects devices to provide "OS descriptors", so Linux-based USB gadgets whishing to be able to talk to a variety of operating systems should be able to provide the "OS descriptors". This patch adds optional support for gadgets whishing to expose the so called "OS Feature Descriptors", that is "Extended Compatibility ID" and "Extended Properties". Hosts which do request "OS descriptors" from gadgets do so during the enumeration phase and before the configuration is set with SET_CONFIGURATION. What is more, those hosts never ask for configurations at indices other than 0. Therefore, gadgets whishing to provide "OS descriptors" must designate one configuration to be used with this kind of hosts - this is what os_desc_config is added for in struct usb_composite_dev. There is an additional advantage to it: if a gadget provides "OS descriptors" and designates one configuration to be used with such non-USB-compliant hosts it can invoke "usb_add_config" in any order because the designated configuration will be reported to be at index 0 anyway. This patch also adds handling vendor-specific requests addressed at device or interface and related to handling "OS descriptors"." Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: add Kconfig for OS descriptorsPeng Fan1-0/+9
Add Kconfig for OS descriptors Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: move utf8_to_utf16le to header fileLi Jun1-73/+1
As other users may use utf8_to_utf16le() to convert the utf8 to utf16 for usb, so move it to head file. Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: OS String supportLi Jun1-0/+26
This is a porting patch from linux kernel: 19824d5eeece ("usb: gadget: OS String support"), original commit log see below: "There is a custom (non-USB IF) extension to the USB standard: http://msdn.microsoft.com/library/windows/hardware/gg463182 They grant permission to use the specification - there is "Microsoft OS Descriptor Specification License Agreement" under the link mentioned above, and its Section 2 "Grant of License", letter (b) reads: "Patent license. Microsoft hereby grants to You a nonexclusive, royalty-free, nontransferable, worldwide license under Microsoft鈥檚 patents embodied solely within the Specification and that are owned or licensable by Microsoft to make, use, import, offer to sell, sell and distribute directly or indirectly to Your Licensees Your Implementation. You may sublicense this patent license to Your Licensees under the same terms and conditions." The said extension is maintained by Microsoft for Microsoft. Yet it is fairly common for various devices to use it, and a popular proprietary operating system expects devices to provide "OS descriptors", so Linux-based USB gadgets whishing to be able to talk to a variety of operating systems should be able to provide the "OS descriptors". This patch adds optional support for gadgets whishing to expose the so called "OS String" under index 0xEE of language 0. The contents of the string is generated based on the qw_sign array and b_vendor_code. Interested gadgets need to set the cdev->use_os_string flag, fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code with a value of their choice. This patch does not however implement responding to any vendor-specific USB requests." Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: don't change ep name for dwc3 while ep autoconfigLi Jun1-0/+2
As the SDP protocol use the predefined ep num for communication, we can't change its name hence reset its ep num while do ep autoconfig, this is only apply for SPL. Signed-off-by: Li Jun <jun.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: Add ep_config call back to usb_gadget_opsYe Li1-0/+4
Since some new fields in usb_ep structure been moved to usb_ss_ep. The CDNS3 gadget driver should replies on this operation to bind the usb_ss_ep with the endpoint descriptor when function layer uses usb_ep_autoconfig to add endpoint descriptors to gadget. So that CDNS3 driver can know the EP information and configure the EP once the set configuration request is received. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-31usb: gadget: Do not export usbd_device_* arraysPali Rohár2-41/+50
Each array is used only in one file (core.c or ep0.c). Move their content to correct file, mark them as static and do not export out of current file. This change allows to decrease size of u-boot.bin as more of those strings are not used. Signed-off-by: Pali Rohár <pali@kernel.org>
2021-01-31thor: add support for the dfu_alt_info reintialization from the flashed scriptMarek Szyprowski1-0/+3
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to ensure that the potential changes to the 'dfu_alt_info' environment variable are applied. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2021-01-31dfu: add 'SCRIPT' entityMarek Szyprowski2-3/+27
Define a new 'SCRIPT' type for DFU entities. The downloaded data are treated as simple u-boot's scripts and executed with run_command_list() function. Flashing the 'SCRIPT' entity might result in changing the 'dfu_alt_info' environment variable from the flashed script, so add a global variable for tracking the potential need to reinitialize the dfu_alt_info related structures. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2021-01-31dfu: add 'SKIP' entityJaehoon Chung2-1/+10
Define a new 'SKIP' type for the DFU entities. The flashed data for that entity is simply ignored without returning any error values. This allows to have one flashing procedure and images for the different board types or variants, where each board uses only the images relevant to it and skips the rest. This is especially usefull for the THOR protocol, which usually transfers more than one file in a single session. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com> [mszyprow: rephrased commit message and docs for easier reading, changed subject to "dfu: add 'SKIP' entity"] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2021-01-31dfu: mmc: use the default MMC device if entity specifies it as -1Marek Szyprowski1-3/+4
Use the default MMC device set in the command line if entity specifies it as -1. This allows to use the same dfu_alt_info string for different MMC devices (like embedded eMMC and external SD card if data layout is the same on both devices). Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
2021-01-31f_fastboot: Avoid use-after-free in the global pointer variableAndy Shevchenko1-1/+1
In case of usb_add_function() failure the error path has an issue, i.e the global pointer variable is assigned to garbage Fix the above mentioned issue by assigning pointer to NULL. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-31f_rockusb: Avoid use-after-free in the global pointer variableAndy Shevchenko1-1/+2
In case of usb_add_function() failure the error path has two issues: - the potentially allocated structure isn't getting freed - the global pointer variable is assigned to garbage Fix the above mentioned issues by freeing memory and assigning NULL. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-31f_rockusb: Use NULL instead of 0 for pointersAndy Shevchenko1-2/+2
get_rkusb() mistakenly uses integers without cast. Convert them to proper type. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2021-01-31gadget: f_thor: fix wrong file size castSeung-Woo Kim1-4/+4
Casting 32bit int value directly into 64bit unsigned type causes wrong value for file size equal or larger than 2GB. Fix the wrong file size by casting uint32_t first. Fixes: commit 1fe9ae76b113 ("gadget: f_thor: update to support more than 4GB file as thor 5.0") Reported-by: Junghoon Kim <jhoon20.kim@samsung.com> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-01-31dfu: Fix handling of UBI partitions in MTD backendGuillermo Rodriguez1-2/+2
For UBI partitions ("partubi" in dfu_alt_info), dfu_fill_entity_mtd sets the mtd.ubi flag; however other functions incorrectly check for nand.ubi instead. Fix this by checking for the correct flag. Signed-off-by: Guillermo Rodriguez <guille.rodriguez@gmail.com> Cc: Lukasz Majewski <lukma@denx.de> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2021-01-31mmc: tmio: sdhi: Configure internal DMA bus widthMarek Vasut3-0/+8
The R-Car3 SDHI should set these two bits in DMA_MODE register according to the specification, to indicate 64bit bus width. No other bus width options are permitted and the default value is 0, which is incorrect. Set the bits accordingly. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
2021-01-30sandbox: fill block device meta informationHeinrich Schuchardt1-0/+11
Provide information about host backed block device. Mark the device created by 'host bind' as removable. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-01-30sandbox: keep time offset when resettingHeinrich Schuchardt1-1/+3
The UEFI Self Certification Test (SCT) checks the SetTime() service with the following steps: * set date * reset * check date matches To be compliant the sandbox should keep the offset to the host RTC during resets. The implementation uses the environment variable UBOOT_SB_TIME_OFFSET to persist the offset. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-01-30dm: core: Update ofnode_read_fmap_entry() to read hashesSimon Glass1-9/+12
At present this function uses the old format for reading hashes. Add support for the current format. Add a test while we are here. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-07-10 10:12:10 +0000