| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
Implement wait_dat0 mmc ops callbac, allowing to reduce SPL boot time.
Before (using grabserial):
[0.000001 0.000001] U-Boot SPL 2021.04-xxxx
[0.028257 0.028257] DDRINFO: start DRAM init
[0.028500 0.000243] DDRINFO: DRAM rate 3000MTS
[0.304627 0.276127] DDRINFO:ddrphy calibration done
[0.305647 0.001020] DDRINFO: ddrmix config done
[0.352584 0.046937] SEC0: RNG instantiated
[0.374299 0.021715] Normal Boot
[0.374675 0.000376] Trying to boot from MMC2
[1.250580 0.875905] NOTICE: BL31: v2.4(release):lf-5.10.72-2.2.0-0-g5782363f9
[1.251985 0.001405] NOTICE: BL31: Built : 08:02:40, Apr 12 2022
[1.522560 0.270575]
[1.522734 0.000174]
[1.522788 0.000054] U-Boot 2021.04-xxxx
After:
[0.000001 0.000001] U-Boot SPL 2021.04-xxxx
[0.001614 0.001614] DDRINFO: start DRAM init
[0.002377 0.000763] DDRINFO: DRAM rate 3000MTS
[0.278494 0.276117] DDRINFO:ddrphy calibration done
[0.279266 0.000772] DDRINFO: ddrmix config done
[0.338432 0.059166] SEC0: RNG instantiated
[0.339051 0.000619] Normal Boot
[0.339431 0.000380] Trying to boot from MMC2
[0.412587 0.073156] NOTICE: BL31: v2.4(release):lf-5.15.5-1.0.0-0-g05f788b
[0.414191 0.001604] NOTICE: BL31: Built : 10:35:26, Apr 6 2022
[0.700685 0.286494]
[0.700793 0.000108]
[0.700845 0.000052] U-Boot 2021.04-xxxx
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
There is no wait_dat0 mmc ops, causing operations waiting for data
line state change (e.g mmc_switch_voltage) to fallback to a 250ms
active delay. mmc_ops still used when DM_MMC is not enabled, which
is often the case for SPL. The result can be unexpectly long SPL
boot time.
This change adds support for wait_dat0() mmc operation.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Fix the end address in the message for unaligned erase request in
mmc_berase() when start + blkcnt is aligned to erase_grp_size.
for example:
- start = 0x2000 - 26
- count = 26
- erase_grp_size = 0x400
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x27ff
But no issue when the end address is not aligned, for example
- start = 0x2000 - 2 * 26
- count = 26
- erase_grp_size = 0x400
Caution! Your devices Erase group is 0x400
The erase range would be change to 0x2000~0x23ff
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Some of the DT compatibles have changed upstream so add new DT compatibles
to ensure things continue to keep working if the device trees are
updated.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Add new lines to make errorr messages easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
This is ported from Linux as of Linux kernel commit
5c2b9c61ae5d8 ("usb: usb251xb: add boost-up property support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
This is used to avoid the ports status of IPPC being brought in kernel
stage, it may cause ports error especially when the xhci controller is
a component of dual-role controller.
Reported-by: Yun-Chien Yu <yun-chien.yu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
|
|
If the device fails to probe - for example, when there is no
ethaddr set - then the private data is automatically freed
but the mdiobus remains registered.
Fixes: 1e354cb39314 ("drivers: net: fsl_enetc: register internal MDIO bus")
Signed-off-by: Michael Walle <michael@walle.cc>
|
|
This driver depends on PCI. Update the Kconfig accordingly.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
|
|
https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
|
|
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
|
|
Add support for i2c devices
|
|
These were only ever implied by sunxi platforms, and that usage has
been removed. Current practice is to specify CONFIG_CONS_INDEX in each
board's defconfig.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Some devices enumerate various clocks in their DT, and many drivers
just blanketly try to enable all of them. This creates problems
since we only model a few gate clocks, and the clock driver outputs
a warning when a clock is not described:
=========
sunxi_set_gate: (CLK#3) unhandled
=========
Some clocks don't have an enable bit, or are already enabled in a
different way, so we might want to just ignore them.
Add a CCU_CLK_F_DUMMY_GATE flag that indicates that case, and define
a GATE_DUMMY macro that can be used in the clock description array.
Define a few clocks, used by some pinctrl devices, that way to suppress
the runtime warnings.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
|
|
The introduction of the DM pinctrl driver made its probe function enable
all clocks enumerated in the DT. This includes the "CLK_BUS_PIO" (and
variations) gate clock. Also CLK_PLL_PERIPH0 is used by the R_CCU device.
So far we didn't describe those clocks in our clock driver.
As we enable them already in the SPL, the devices happen to work, but
the clock driver still complains about not finding those clocks:
=========
sunxi_set_gate: (CLK#58) unhandled
=========
Add the one-liners that are needed to announce the gate bit for those
clocks, to silence that message on the console.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
|
|
H6 is from the sun50i family, not sun6i.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Now that the pinmux conflict is handled in the board code (by skipping
setup for the one conflicting MMC controller), the driver does not need
to be entirely disabled based on the UART pinmux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
Add the tpm2_tis_i2c driver that should support any TPMv2 compliant
I2C chips, such as the NPCT75X chip.
[Ilias rename priv_auto_alloc_size to priv_auto]
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
Commit 0980cbba7b3c ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy
support") changed number of sectors which are read but did not adjusted
error check.
Fix it and check for if correct number of sectors were read.
Fixes: 0980cbba7b3c ("mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode
and logically calls spi_get_bus_and_cs(). In case spi mode and speed are
not read from DT, make usage of spi_flash_probe() instead.
To sum-up:
- Previous call tree was:
spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
- Current call tree is:
spi_flash_probe() -> _spi_get_bus_and_cs()
spi_flash_probe_bus_cs() -> spi_get_bus_and_cs()
This patch impacts the following :
- cmd/sf.c: if spi mode and/or speed is passed in argument of
do_spi_flash_probe(), call spi_flash_probe() otherwise call
spi_flash_probe_bus_cs().
- drivers/net/fm/fm.c: as by default spi speed and mode was set to
0 and a comment indicates that speed and mode are read from DT,
use spi_flash_probe_bus_cs().
- drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read
from DT by all platforms using this driver, so keep legacy and replace
spi_flash_probe_bus_cs() by spi_flash_probe();
- drivers/net/sni_netsec.c : spi speed and mode are not read from DT,
so replace spi_flash_probe_bus_cs() by spi_flash_probe().
- drivers/usb/gadget/max3420_udc.c: Can't find any platform which make
usage of this driver, nevertheless, keep legacy and replace
spi_get_bus_and_cs() by _spi_get_bus_and_cs().
- env/sf.c: a comment indicates that speed and mode are read
from DT. So use spi_flash_probe_bus_cs().
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
|
|
Move legacy spi_get_bus_and_cs() code to _spi_get_bus_and_cs().
Add new spi_get_bus_and_cs() implementation which rely on DT
for speed and mode and don't need any drv_name nor dev_name
parameters. This will prepare the ground for next patch.
Update all callers to use _spi_get_bus_and_cs() to keep the
same behavior.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: "Pali Rohár" <pali@kernel.org>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Anji J <anji.jagarlmudi@nxp.com>
Cc: Biwen Li <biwen.li@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
|
|
Requesting the locality uses the timeout values, so they need
to be set beforehand.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20220523
-------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/12087
Additionally to u-boot-imx20200520:
- DH MX8MP
- i.MX GPIO: reading GPIO when direction is output
- Menlo i.MX53: switch to DM
And from u-boot-imx20200520:
- fix Verdin hang
- add pca9450 regulator
- conversion to DM_SERIAL
- NAND block handling
- fix crypto
- enable cache on some boards
- add ACC board (MX6)
|
|
Add support for reading GPIO pin value when function is output.
With this patch applied, gpio toggle command is working.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
The f1c100s has a clock tree similar to those of other sunxi parts.
Add support for it.
Signed-off-by: George Hilliard <thirtythreeforty@gmail.com>
Signed-off-by: Yifan Gu <me@yifangu.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
[Andre: add PIO and I2C]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
|
|
|
|
Missing nodes may also be signaled via -ENODATA. We need to check for
that to prevent failing in non-usb3 setups.
Furthermore, dev.phy must be NULL'ed in case usb3-phy was not found.
Fixes: 142d50fbce7c ("usb: dwc3: Add support for usb3-phy PHY configuration")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
|
|
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The upstream DT regulators node subnodes are named BUCKn and LDOn,
the downstream DT regulators node subnodes are named buckn and ldon,
add the upstream match.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The specific implementation was having bug. Those bugs are since
the beginning of the implementation. Some manufactures can already
experience this bug in their SPL code. This bug can be more visible on
architecture that has complicated boot process like imx8mn. Older
version of uboot can be affected if the bad block
appear in correspoding of the beginning of u-boot image. In order to
adjust the function we scan from the first erase block.
The problematic part of old code was in this part:
while (is_badblock(mtd, offs, 1)) {
page = page + nand_page_per_block;
/* Check i we've reached the end of flash. */
if (page >= mtd->size >> chip->page_shift) {
free(page_buf);
return -ENOMEM;
}
}
Even we fix it adding increment of the offset of one erase block size
, we don't fix the problem, because the first erase block where the
image start is not checked. The code was tested on an imx8mn where
the boot rom api was not able to skip it. This code is used by other
architecures like imx6 and imx8mm
Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
Move the hook after nand_scan_tail is called. The hook must be replaced
to the mxs specific one but those must to be assignment later in the
probe function.
With this fix markbad is working again. Before this change:
nand markbad 0xDEC00
NXS NAND: Writing OOB isn't supported
NXS NAND: Writing OOB isn't supported
block 0x000dec00 NOT marked as bad! ERROR 0
Cc: Han Xu <han.xu@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
|
|
HW accelerated hash operations are giving incorrect hash output.
so add flush and invalidate for input/output hash buffers.
Fixes: 94e3c8c4fd (crypto/fsl - Add progressive hashing support using hardware acceleration.)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
|
|
implement get f/w version api.
print ele f/w version in spl.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
|
|
When the device tree indicates support for role switching through
the "usb-role-switch" property, take the "role-switch-default-mode"
property into account when deciding which role to put the
controller into.
This makes USB devices work on Apple M1 systems where the device
tree may include a "dr_mode" property that is set to "otg", but
where we need to put the controller into "host" mode to see
devices connected to the type-C ports.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
|
|
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me
tmp = 0x00ffff00
tmp = 0x00070700
tmp = 0x00000000
tmp = 0x00101000
and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.
So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.
This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
rng driver enabled to read random number using caam.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
|
|
RNG Hardware error is reported due to incorrect entropy delay
rng self test are run to determine the correct ent_dly.
test is executed with different voltage and temperature to identify the
worst case value for ent_dly. after adding a margin value(1000),
ent_dly should be at least 12000.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
|
|
Because mxs_nand_spl driver does not support DM, to use the minimum ECC
layout, it needs to handle the CONFIG_NAND_MXS_USE_MINIMUM_ECC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Han Xu <han.xu@nxp.com>
|
|
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes have been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
|
|
Observing psgtr pll timeouts with some usb hubs and devices behind it.
Increase timeout to 10ms to take care of it.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220510131234.2650-1-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
|
|
Currently, pinctrl drivers only get probed if pinconf is actually being
used, however on SoC-s like Armada 3720 pinctrl driver is a also the GPIO
driver.
So, if the pinctrl driver doesn't get probed GPIO-s won't get registered
and thus they cannot be used.
This is a problem on the Methode eDPU as it just uses SB pins as GPIO-s
and without them being registered networking won't work as it only has
one SFP slot and the TX disable GPIO is on the SB controller.
So, probe the pinctrl drivers using DM_FLAG_PROBE_AFTER_BIND like LED
uclass does.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Use CONFIG_VAL(DEBUG_UART_BASE) instead of CONFIG_DEBUG_UART_BASE, so
proper config value (CONFIG_DEBUG_UART_BASE or CONFIG_SPL_DEBUG_UART_BASE)
is used based on building target.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
TPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for TPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
SPL_DEBUG_UART_BASE is same as DEBUG_UART_BASE, but applies only for SPL.
In some cases base address of UART is different in SPL and proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
zynqmp_pm_is_function_supported() which checks feature support on som,
which is implemented in firmware_zynqmp.c driver. As mini configuration
does not use firmware driver, so create a weak function to avoid
compilation error on zynqmp mini configuration.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c60655a509956b8fc3a81671a7dc51157f3973db.1651048030.git.michal.simek@xilinx.com
|
|
The call to xilinx_pm_request requires an array of a larger size.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/5f1409de285d7454af171a54e5f115da9d82c44e.1650440343.git.michal.simek@xilinx.com
|
|
The call to xilinx_pm_request requires an array of a larger size.
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Link: https://lore.kernel.org/r/20220416181530.2311155-1-jorge@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
