Age | Commit message (Collapse) | Author | Files | Lines |
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Needed for redundant environment for example.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
|
|
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
There are two problems in the current timeout loop implementation:
1. In case initial test failing, there will always be a delay of 1 ms
2. The delay duration is not tunable
The new implementation addresses both these limitations.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
If the flash size was smaller than 1MB then flash_print_info()
was erroneously reporting 0 MB.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
THis patch introduces a new methodology for flash probing
in which flash_devices[] table, looked-up thru the dev_id, is
used to locate the flash geometry and information.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Since the smi erase code is very generic and works for any kind
of flash, there is no need to test for ST_M25Pxx_ID flash types
like m25p40 flashes).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
smi_read_sr fails sometimes because of TFF not getting set within assumed time.
This condition may arise because of, for example, smi memory being in a erase
mode.
This fix is to enable reading the status register until timeout.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
SMI driver read status fails because the control register could not be
overwritten. Instead, the read status should be tried until timeout.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This commit does the following:
- Reports error if SNOR flash is not found on the board
- Changes smi_read_sr to return error using which a retry mechanism is
implemented for reading flash status
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Curently the code makes wrong assumption that the Transfer finished flag shall
be set within the stipulated time. However, there may occur a scenario in which
the TFF flag is not set. Return error in that case.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
SMI is the serial memory interface controller provided by ST.
Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|