aboutsummaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)AuthorFilesLines
2020-04-06configs: versal: Add CONFIG_DISTRO_DEFAULTS to versal defconfigT Karthik Reddy1-15/+1
Add DISTRO_DEFAULTS config to versal virt defconfig file which is suitable for booting general purpose Linux distributions. Remove other configs which are selected by default by DISTRO_DEFAULTS configuration. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06arm64: dts: meson: add libretech-pc supportJerome Brunet2-0/+146
Add support for the Amlogic based libretech-pc platform. This platform comes with 2 variant, based on the s905d or s912 SoC. Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> [narmstrong: update board/amlogic/q200/MAINTAINERS] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-04-03Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-tegraTom Rini7-0/+72
- Add support for Jetson Nano, plus miscellaneous other fixes found during Nano bringup. - Add Igor's update_uboot wrapper patches.
2020-04-02ARM: tegra: Add NVIDIA Jetson Nano Developer Kit supportTom Warren1-0/+64
The Jetson Nano Developer Kit is a Tegra X1-based development board. It is similar to Jetson TX1 but it is not pin compatible. It features 4GB of LPDDR4, a SPI NOR flash for early boot firmware and an SD card slot used for storage. HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0 and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI Ethernet controller provides onboard network connectivity. NVMe support has also been added. Env save is at the end of QSPI (4MB-8K). A 40-pin header on the board can be used to extend the capabilities and exposed interfaces of the Jetson Nano. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Tested-by: Peter Robinson <pbrobinson@gmail.com>
2020-04-02tegra: Enable CONFIG_BOOTP_PREFER_SERVERIP for all Jetson boardsTom Warren6-0/+6
This allows the user to set $serverip in the environment before executing a DHCP request. If they do, U-Boot will use that IP rather than using the IP in the DHCP response. Signed-off-by: Tom Warren <twarren@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2020-04-02ARM: tegra: p2771-0000: enable PIE relocationVishruth2-0/+2
U-Boot is configured to build as position independent executable. Enable relocation of RELA section required to work with different load addresses. Signed-off-by: Vishruth <vishruthj@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Tested-by: Peter Robinson <probinson@gmail.com>
2020-04-02rockchip: Enable HDMI output on rk3399 board w/ HDMIJagan Teki5-0/+34
Enable config options and console setting to respective rk3399 board for HDMI output. Boards supported and tested on this patch are: - NanoPc T4 - NanoPi M4 - NanoPi Neo4 - ROC-RK3399-PC - Rock960 Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-31Merge branch 'next' of git://git.denx.de/u-boot-usb into nextTom Rini8-2/+7
2020-03-31Merge tag 'efi-2020-04-rc5' of ↵Tom Rini1-1/+1
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-04-rc5 This series fixes: * UEFI Python tests CONFIG_OF_CONTROL=y. * int to pointer cast warning for cmd/efidebug.c * memory reservation even if fdt node is disabled Now that the Python test is fixed reintroduce the reverted patch for vexpress_ca9x4 to enable EFI_LOADER and define the dtb file name.
2020-03-31Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini1-2/+2
- Fixes for Gen 2 V2H Blanche
2020-03-30Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini45-3/+89
- Fixes env variable for layerscape platforms, disable hs200. - Fixes board fixup, mux setting, enable gic, fspi on lx2160a, Fixes I2C DM Warning on ls1043a, ls1046a - Fixes RGMII port on ls1046ardb, ls1046ardb and DM_USB Warning on ls1012afrdm, ls1021aiot
2020-03-30Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini151-872/+2
- SPL SPI support R40, H6 (Andre) - eMMC boot part on a64-olinuxino (Petr)
2020-03-30configs: lx2160a: Define ENV_ADDR valueKuldeep Singh2-0/+2
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init. Define the value as 0x20500000 for lx2160ardb and lx2160aqds. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30configs: lx2160a: Enable FSPI supportKuldeep Singh4-0/+8
Enable FSPI controller support. So, flash environment can now be used. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30configs: disable eMMC HS200 support on layerscape platformsYangbo Lu3-3/+0
The eMMC HS200 speed mode on Layerscape platforms has not been supported properly. The eSDHC clock tuning has not been implemented by now. So disable it until it is supported properly in case of any potential issues. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30configs: ls1012ardb: secure boot: Add PFE configPriyanka Singh1-0/+2
Add config to enable the PFE and ETH support. Also change the pfe secure boot header address. Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30configs: arm: ls1021aiot: enable CONFIG_DM_USB supportRan Wang1-0/+1
Enable CONFIG_DM_USB to remove below compile warning: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30configs: arm64: ls1012afrdm Enable CONFIG_BLKRan Wang2-0/+2
With DM_USB enabled, enable CONFIG_BLK to remove this compile warning for ls1012afrdm based targets: ===================== WARNING ====================== This board does not use CONFIG_DM_USB. Please update the board to use CONFIG_DM_USB before the v2019.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Ran Wang <ran.wang_1@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30dm: arm64: ls1046a: add i2c DM supportBiwen Li18-0/+36
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1046A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30dm: arm64: ls1043a: add i2c DM supportBiwen Li17-0/+34
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1043A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30configs: lx2160a: Enable GIC_V3_ITS configWasim Khan4-0/+4
Enable GIC_V3_ITS config to program GIC LPI configuration table. Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-03-30ARM: rmobile: Convert Gen2 Blanche to DM_SPI{,_FLASH}Marek Vasut1-2/+2
Enable DM_SPI and DM_SPI_FLASH in U-Boot on V2H Blanche. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2020-03-28configs: a64-olinuxino-emmc: add eMMC boot part config commandsPetr Štetiar1-0/+1
mmc bootbus and partconf commands are needed in order to be able to configure booting from separate boot0/boot1 eMMC partitions. Signed-off-by: Petr Štetiar <ynezz@true.cz> [jagan: rebase on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-28vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader.Kristian Amlie1-1/+1
EFI was disabled in f95b8a4b5f64f because of the missing DTB file, and indeed, the DTB file is required to load recent versions of GRUB (2.04) correctly. Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
2020-03-27Revert "vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader."Tom Rini1-1/+1
Currently this causes failures of the platform when running the EFI loader tests, so disable it for now. This reverts commit af827140e5965e5bb2bcad1c53ca8419b428ff6d. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-03-26Merge tag 'u-boot-rockchip-20200327' of ↵Tom Rini6-0/+7
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Fixed for rv1108 and elgin-rv1108 board - Fix the keyboard from USB instead of CrOS EC
2020-03-26elgin-rv1108: Avoid adc_channel_single_shot errorOtavio Salvador1-0/+1
Currently the following error message is seen during boot: U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB APLL: 600000000 DPLL:1200000000 GPLL:1188000000 ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000 MMC: dwmmc@30110000: 0 Loading Environment from MMC... OK In: serial@10210000 Out: serial@10210000 Err: serial@10210000 Model: Elgin RV1108 R1 board rockchip_dnl_key_pressed: adc_channel_single_shot fail! .... Since the elgin-rv1108 does not use ADC to read the download key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid such error. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26elgin-rv1108: Use rk_board_late_init() for GPIO settingsOtavio Salvador1-0/+1
Since commit 8e9a8d0d0c8c ("rockchip: elgin-rv1108: use board_early_init_f for per-boar init") the function that configure the board GPIOs is no longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected. These GPIOs do not need to be configured in such early stagem, so change it to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y to fix the regression. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26rockchip: Change keyboard input from CrOS EC keyboard to a USB keyboardPeter Robinson5-0/+5
These boards aren't ChromeOS devices so won't have a cros-ec-keyb input as it's the keyboard available via the ChromeOS Embedded Controller. Update them to use a USB keyboard which would actually be available. Also enable the usb keyboard option for those devices that don't have it enabled already. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-23vexpress_ca9x4: Enable use of correct DTB file and restore EFI loader.Kristian Amlie1-1/+1
EFI was disabled in f95b8a4b5f64f because of the missing DTB file, and indeed, the DTB file is required to load recent versions of GRUB (2.04) correctly. Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
2020-03-18sunxi: Remove no longer needed default options from defconfigsAndre Przywara151-872/+0
Now that those common Allwinner config symbols are defined automatically for all boards in their Kconfig files, we can remove the now redundant definitions from the boards' _defconfig files. Some boards had a differing definiton for some of those symbols, it looks like mostly to "merge races" when the symbol was introduced (new board *_defconfig file missed the "add symbol to all files" patch). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <mripard@kernel.org> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-18sunxi: Pine H64: Enable SPI booting in defconfigAndre Przywara1-0/+1
The Pine H64 board comes with some onboard SPI flash chip, which is perfect for loading SPL, ATF and U-Boot proper from there. Enable the functionality in the defconfig, so that we use sunxi-fel to transfer a bootable image to the NOR flash. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2020-03-17Merge tag 'ti-v2020.07-next' of ↵Tom Rini10-9/+177
https://gitlab.denx.de/u-boot/custodians/u-boot-ti into next K3 J721E: * OSPI boot support * Support for loading remote cores in R5 SPL * PMIC ESM Support * Minor fixes for R5F and C7x remoteproc drivers K3 AM654: * Update AVS class 0 voltages. * Add I2C nodes DRA7xx/AM57xx: * Fixed Android boot on AM57xx AM33/AM43/Davinci: * switch to driver model for the net and mdio driver for baltos * Add DM/DTS support for omap video driver * Enable fastboot on am335x-evm
2020-03-16configs: Drop '$(ARCH)' usage in CONFIG_SPL_LDSCRIPTTom Rini3-3/+3
In a few boards we had overridden, intentionally, the value used for CONFIG_SPL_LDSCRIPT. However, rather than using the ARCH value (arm) they used the $(ARCH) variable in make. This doesn't help really, so switch to a hard-coded value. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-03-16edminiv2: Move CONFIG_SPL_LDSCRIPT to defconfigTom Rini1-0/+1
As there is only one machine under mach-orion5x, having a Kconfig entry for SPL_LDSCRIPT is not helpful, move this to the defconfig file. Suggested-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
2020-03-16mx31pdk: Move CONFIG_SPL_LDSCRIPT to defconfigTom Rini1-0/+1
As there is only one mx31pdk config file and with upcoming updates to the Kconfig parsing logic, rather than have an entry in board/freescale/mx31pdk/Kconfig, move this single setting to the defconfig file. Cc: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
2020-03-12Merge tag 'efi-2020-04-rc4-3' of ↵Tom Rini2-2/+0
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-04-rc4 (3) This pull request provides the hardware RNG driver for Amlogic systems needed for the EFI_RNG_PROTOCOL. Furthermore bug fixes are provided: * correct an error message in the efidebug command * correct an error in the 'efidebug rm' command * remove an unnecessary assignment in efi_queue_event()
2020-03-12test: enable RSA library test on sandboxAKASHI Takahiro4-0/+4
We want to always run RSA library test on sandbox build in Travis CI. Just adding CONFIG_RSA_VERIFY_WITH_PKEY would be good enough for this purpose. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
2020-03-11drivers/rng: simplify KconfigHeinrich Schuchardt2-2/+0
For all sandbox systems with DM_RNG we enable RNG_SANDBOX. So we can simply set the default to yes. All rng drivers depend on DM_RNG. Use a single 'if' instead of individual dependencies. Now 'make menuconfig' shows the individual drivers neatly indented under the DM_RNG entry. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-03-11defconfigs: am65x_hs_evm: Sync HS and non-HS defconfigsAndrew F. Davis2-4/+50
Additions have been made to the non-HS defconfig without the same being made to the HS defconfig, sync them. Signed-off-by: Andrew F. Davis <afd@ti.com>
2020-03-10Merge tag 'mmc-2020-3-9' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini5-0/+41
- DM support for CAxxxx SoCs - eMMC board for presidio-asic - Add defer probe for mmc sdhci - TI SoCs mmc misc update
2020-03-10Merge tag 'u-boot-imx-20200310' of ↵Tom Rini10-118/+17
https://gitlab.denx.de/u-boot/custodians/u-boot-imx Fixes for 2020.04 ----------------- - DM : mx6sabresd - mx6ul_14x14_evk: fix video - mx8qxp; fix console for booting - sync DTS with kernel (imx6sx) - drop obsolete woodburn (mx35) Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/660550811
2020-03-10Merge tag 'u-boot-atmel-fixes-2020.04-a' of ↵Tom Rini1-0/+1
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel First set of u-boot-atmel fixes for 2020.04 cycle: - Includes two small configuration fixes that will solve the SPL booting on sama5d3_xplained board.
2020-03-10mx6slevk: Convert to DM_ETHPedro Jardim1-0/+3
This fixes the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-10mx6sabreauto: Convert to DM_ETHPedro Jardim1-0/+5
This fixes the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-10mx7dsabresd: Boot in non secure by defaultFabio Estevam2-2/+0
Booting a mainline kernel in secure mode on i.MX7D causes only one CPU to be brought up. Change it to booting in non secure mode by default, which allows the two CPUs to be brought up. It does have a side effect of not probing the CAAM driver. If CAAM driver is needed then a secure world OS such as OPTEE needs to be used. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-10mx6sabresd: Convert ethernet to driver modelAlifer Moraes1-0/+5
Convert imx6sabresd ethernet to driver model to fix the following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-03-10board: sama5d3_xplained: Fix SPL DTB read from NANDFabien Lehoussel1-0/+1
SPL boot cannot find dtb if CONFIG_SPL_SEPARATE_BSS is disabled : CONFIG_SPL_SEPARATE_BSS=n RomBOOT <debug_uart> Missing DTB ### ERROR ### Please RESET the board ### RomBOOT CONFIG_SPL_SEPARATE_BSS=y RomBOOT <debug_uart> U-Boot SPL 2019.04-linux4sam_6.2-icp-dirty (Feb 24 2020 - 15:34:35 +0100) Trying to boot from NAND <debug_uart> Signed-off-by: Fabien Lehoussel <fabien.lehoussel@medianesysteme.com>
2020-03-09mx6sxsabresd: Enable DM_PCIFabio Estevam1-0/+1
Enale DM_PCI support in order to avoid board removal from the project. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-03-09configs: imxrt1050-evk: enable D/I cacheGiulio Benetti1-2/+0
Soc supports cache so let's enable it. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
generated by cgit v1.1 at 2024-07-15 20:14:18 +0000