aboutsummaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)AuthorFilesLines
2014-11-24Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini4-4/+4
2014-11-24Merge git://git.denx.de/u-boot-x86Tom Rini1-0/+10
Conflicts: arch/x86/cpu/Makefile Signed-off-by: Tom Rini <trini@ti.com>
2014-11-24gw_ventana: Use the generic spl_sd.cfgFabio Estevam1-1/+1
gw_ventana can boot from SPI or NAND and both of these interfaces boot from the same 0x400 offset. This means that we could simplify the code and replace the custom gw_ventana.cfg with the generic spl_sd.cfg, as it provides the same boot offset of 0x400. Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-23ARM: bcm: Enable bcm11130 boardsSteve Rae2-0/+6
bcm11130 bcm11130_nand Signed-off-by: Steve Rae <srae@broadcom.com>
2014-11-23ARM: bcm: Enable five Cygnus boardsSteve Rae7-3/+18
bcm911360_entphn bcm911360_entphn-ns bcm911360k bcm958300k-ns bcm958305k - updates to support Cygnus and NSP board families better - add functions so CONFIG_ARMV7_NONSEC can be enabled on Cygnus boards Signed-off-by: Steve Rae <srae@broadcom.com>
2014-11-21x86: Add chromebook_link boardSimon Glass1-0/+10
This board is a 'bare' version of the existing 'link 'board. It does not require coreboot to run, but is intended to start directly from the reset vector. This initial commit has place holders for a wide range of features. These will be added in follow-on patches and series. So far it cannot be booted as there is no ROM image produced, but it does build without errors. Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-20mx6: Use a common SPL configuration fileFabio Estevam3-3/+3
Many boards use a minimal .cfg file in the SPL case. Introduce spl_sd.cfg so that we can reuse it. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-11-19mpc83xx: Add gdsys hrcon boardDirk Eibach1-0/+3
The gdsys hrcon board is based on a Freescale MPC8308 SOC. It boots from NOR-Flash, kernel and rootfs are stored on SD-Card. On board peripherals include: - 1x GbE (optional) - Lattice ECP3 FPGA connected via eLBC and PCIe Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc> Signed-off-by: Stefan Roese <sr@denx.de>
2014-11-17ARM: atmel: add sama5d4 xplained ultra board supportBo Shen3-0/+9
The code for this board supports following features: - Boot media support: NAND flash/SD card/SPI flash - Support LCD display (optional, disabled by default) - Support ethernet - Support USB mass storage Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17ARM: atmel: add sama5d4ek board supportBo Shen3-0/+9
The code for this board supports following features: - Boot media support: NAND flash/SD card/SPI flash - Support LCD display - Support ethernet - Support USB mass storage Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, spl, at91: add spl support for the corvus boardHeiko Schocher1-2/+3
replaces the at91bootstrap code with SPL code. make the spl image with: ./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin this writes the length of the spl image into the 6th execption vector. This is needed from the ROM bootloader. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bo Shen <voice.shen@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17arm, at91, spl: add spl support for the taurus boardHeiko Schocher1-2/+3
replaces the at91bootstrap code with SPL code. make the spl image with: ./tools/mkimage -T atmelimage -d spl/u-boot-spl.bin spl/boot.bin this writes the length of the spl image into the 6th execption vector. This is needed from the ROM bootloader. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini4-1/+4
2014-11-17Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini4-3/+6
2014-11-17sh: Move SH_32BIT to KconfigNobuhiro Iwamatsu4-1/+4
This moves SH_32BIT to Kconfig, and removes SH_32BIT from config files. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-14Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2-0/+8
2014-11-13arm: mx6: add support for TBS2910 Matrix ARM miniPCSoeren Moch1-0/+3
Add initial support for TBS2910 Matrix ARM miniPC. Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC. Signed-off-by: Soeren Moch <smoch@web.de>
2014-11-13Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini8-10/+35
2014-11-13imx6: add spl config for mx6sabresdJohn Tobias1-0/+5
add a build configuration file for mx6sabresd with spl support Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
2014-11-13arm: mx6: Fix missing Kconfig option for NovenaMarek Vasut1-1/+1
Add two missing Kconfig options for Novena and drop the SPL from the Novena config. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2014-11-13sun6i: ehci: Add sun6i ehci supportHans de Goede1-0/+3
Add support for the 2 ehci controllers found on the sun6i (A31) soc. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk> Acked-by: Marek Vasut <marex@denx.de>
2014-11-13sunxi: ehci: Add proper Kconfig options to select the usb Vbus gpio-sHans de Goede6-6/+12
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to Kconfig being the right thing to do, an added advantage of this is that it allows for boards without Vbus gpio-s. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Add Mele M9 boardHans de Goede1-0/+15
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13sun6i: Enable SPLHans de Goede1-4/+5
Enable the SPL now that we've all the necessary bits in place. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-11-13zynq: zybo: Move CONFIG_DEFAULT_DEVICE_TREE to defconfigMichal Simek1-0/+2
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Move CONFIG_DEFAULT_DEVICE_TREE from board config directly to defconfig. This patch removes compilation warning: include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE" redefined [enabled by default] #define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-13Merge branch 'zynq' of git://www.denx.de/git/u-boot-microblazeTom Rini1-0/+4
2014-11-12powerpc: remove orphaned boards mcc200 and prs200Nikita Kiryanov12-47/+0
mcc200 and prs200 are old and have no maintainer. Remove the boards. This also removes the mcc200 specific 1bpp BMP support from common/lcd.c Cc: Wolfgang Denk <wd@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-11-11Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini1-0/+5
2014-11-12ARM: UniPhier: enable USB featuresMasahiro Yamada3-0/+9
FAT-formated USB storage device access is available. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-11kconfig: zynq: Add ZYBO boardPeter Crosthwaite1-0/+4
Add a defconfig and Kconfigury for the Digilent ZYBO board. Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-11-10arm: rmobile: kconfig: Remove '+S:' prefix from defconfig filesNobuhiro Iwamatsu3-3/+3
'+S' is unnecessary because boards of rmobile do not use SPL. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-10arm: rmobile: Add support gose boardNobuhiro Iwamatsu1-0/+3
The gose board has R8A7793, 1GB DDR3-SDRAM, USB, Ethernet, and more. This patch supports the following functions: - DDR3-SDRAM - SCIF - QSPI - SPI Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> CC: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-07Merge git://git.denx.de/u-boot-tiTom Rini3-2/+8
2014-11-07arm: socfpga: Add DT support for SoCFPGA and add socfpga_socrates targetStefan Roese1-0/+5
This patch includes the latest DT sources for socfpga from the current Linux kernel. And enables CONFIG_OF_CONTROL for the new build target "socfpga_socrates" (the EBV SoCrates board) to make use of this new DT support. Until this patch, the only SoCFPGA U-Boot target in mainline is "socfpga_cyclone5". This build target is not (yet) changed to support DT. So nothing changes for this target. Even though the long-term goal should be to move all SoCFPGA targets over to DT. One of the reasons to enable DT support in SoCFPGA is, that I need to support multiple different SPI controllers for this platform. This is the QSPI Cadence controller and the Designware SPI master controller. Both are implemented in the SoCFPGA. And enabling both controllers is only possible by using the new driver model (DM). The DM SPI code only supports DT based probing. So it was easier to move SoCFPGA to DT than to add the (deprecated) platform-data based probing to the DM SPI suport. Note that the image with the dtb embedded is u-boot-dtb.img. This needs to be used now for those DT enabled boards instead of u-boot.img. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Vince Bridgers <vbridger@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Pavel Machek <pavel@denx.de> Cc: Simon Glass <sjg@chromium.org>
2014-11-06omap3: cm-t3517: add basic board supportIgor Grinberg1-0/+4
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC. Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT, Analog audio codec, touch screen controller, LED. Add basic support including: LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2014-11-05Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini1-0/+4
2014-11-05am335x_evm: Convert NOR_BOOT to KconfigTom Rini1-1/+1
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-05am335x_evm: Add NOR to KconfigTom Rini2-2/+4
Make enabling support for NOR (and describe where it's seen) be done via Kconfig. Signed-off-by: Tom Rini <trini@ti.com>
2014-11-05dm: sunxi: Add a new config for an FDT-based pcDuino3Simon Glass1-0/+11
For now we won't want to mess with the existing configurations. Create a new one which will enable device tree and driver model. Note that this brings the device tree binary into u-boot-sunxi-with-spl.bin. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: kconfig: Introduce CONFIG_TARGET_<BOARD>Ian Campbell24-24/+47
This was done automatically with the following bits of scripting. The Kconfig choice content was generated with this script snippet: for i in $(git grep -l CONFIG_ARCH_SUNXI configs/*) ; do TARGET=$(sed -n -e 's/CONFIG_SYS_EXTRA_OPTIONS="\([^,"]\+\).*/\1/p' $i); MACH=$(sed -n -e 's/.*CONFIG_\(MACH_SUN.I\)=./\1/p' $i) echo "config TARGET_$TARGET" echo " bool \"$TARGET\"" echo " depends on $MACH" echo done defconfigs were updated with a sed script (t): # Extract board from first entry of CONFIG_SYS_EXTRA_OPTIONS, /^CONFIG_SYS_EXTRA_OPTIONS/ { s/^\(CONFIG_SYS_EXTRA_OPTIONS="\)\([^,"]\+\),\?\(.*\)/\1\3\nCONFIG_TARGET_\2=y/; # Print and delete first line (CONFIG_SYS_EXTRA_OPTIONS), leaving # CONFIG_TARGET_<BOARD> in pattern space P;D; }; # Move CONFIG_TARGET_<BOARD> to hold space /^CONFIG_TARGET/{h;n} # Print CONFIG_TARGET_<BOARD> after CONFIG_MACH_<SOC> in either SPL or # normal mode. /^CONFIG_MACH/{p;g;p;n}; /^\+S:CONFIG_MACH/{p;g;s/^CONFIG_TARGET/+S:&/;p;n}; # Print any remaining lines normally p; Run as: sed -i -n -f t $(git grep -l CONFIG_ARCH_SUNXI configs/*) and then manually removing the one instance of CONFIG_SYS_EXTRA_OPTIONS="" from Colombus_defconfig board/sunxi/Makefile was updated with: sed -e 's/^\(obj-\$(CONFIG_\)\(.*\)\().*+= dram_.*\)/\1TARGET_\2\3/g' board/sunxi/Makefile and manually retabbing a few lines to line up again. The board descriptions could certainly be improved. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: Drop FEL variants of defconfigs.Ian Campbell2-14/+0
This can now be configured via Kconfig, e.g. with: $ make BOARD_defconfig $ echo CONFIG_SPL_FEL=y >> .config $ echo CONFIG_SPL_FEL=y >> spl/.config Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: Kconfig: Make SPL_FEL a toplevel Kconfig optionIan Campbell2-2/+4
It's unfortunate that this needs to be present in both .config and spl/.config since it makes it slightly hard to enable FEL mode for a regular defconfig. It can be done with: echo CONFIG_SPL_FEL=y >> .config echo CONFIG_SPL_FEL=y >> spl/.config Ideally only one of those would be needed. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: kconfig: Rename TARGET_SUN[45678]I to MACH_SUN[45678]I.Ian Campbell26-26/+26
Now we have CONFIG_ARCH_SUNXI as the toplevel, CONFIG_MACH_SUN[45678]I as the per-SoC option and leave CONFIG_TARGET_BLAH free for individual boards in the future. Done automatically with: sed -i -e 's/TARGET_\(SUN[45678]I\)/MACH_\1/g' $(git grep -l TARGET_SUN[45678]I) Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: kconfig: Add top-level ARCH_SUNXIIan Campbell26-0/+26
And make TARGET_SUN[45678]I a choice variable under this. configs updated with: sed -i -e 's/^\(\+S:\)\?CONFIG_TARGET_SUN.I=y/\1CONFIG_ARCH_SUNXI=y\n&/g' configs/* Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05ARM: sunxi: Fix Ippo-q8h-v5 defconfig filenameChen-Yu Tsai1-0/+0
The defconfig for Ippo-q8h-v5 was incorrectly committed as "Ippo_q8h". This patch renames it correctly, as well as correct a typo in my name in the maintainers listing. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04sparc: move CONFIG_SYS_TEXT_BASE to KconfigMasahiro Yamada5-0/+5
Defining CONFIG_SYS_TEXT_BASE in config.mk is very old style. Create CONFIG_SYS_TEXT_BASE option in Kconfig, but let it depend on CONFIG_SPARC because we do not want to disturb the other architectures that still define CONFIG_SYS_TEXT_BASE in their header files. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Daniel Hellstrom <daniel@gaisler.com>
2014-11-01MIPS: kconfig: add options for vct board variant selectDaniel Schwierzeck12-12/+24
The vct board can be built with various variants which are configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus add new Kconfig options for those board variants. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Stefan Roese <sr@denx.de>
2014-11-01MIPS: kconfig: add options for dbau1x00 board variant selectDaniel Schwierzeck4-4/+4
The dbau1x00 board can be built with various variants which are configured via CONFIG_SYS_EXTRA_OPTIONS. This is deprecated. Thus add new Kconfig options for those board variants. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01MIPS: kconfig: merge targets qemu_mips and qemu_mips64Daniel Schwierzeck4-2/+6
Now the user can separately select the CPU type. Thus the targets qemu_mips and qemu_mips64 can be merged to a single target. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2014-11-01MIPS: kconfig: add options for endianess selectDaniel Schwierzeck24-7/+25
Add new Kconfig option to let the user select the targets endianess. Each target have to select SUPPORTS_BIG_ENDIAN and/or SUPPORTS_LITTLE_ENDIAN to indicate which endianess is supported. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
generated by cgit v1.1 at 2024-07-10 04:25:03 +0000