aboutsummaryrefslogtreecommitdiff
path: root/configs
AgeCommit message (Collapse)AuthorFilesLines
2021-10-07Merge tag 'u-boot-amlogic-20211007' of ↵WIP/07Oct2021Tom Rini6-0/+437
https://source.denx.de/u-boot/custodians/u-boot-amlogic - Add new SoC ID for S905Y2 found in Radxa Zero - pcie_dw_meson: fix usb fail when pci link fails to go up - Sync Amlogic DT from Linux 5.14 - dwc3-meson-gxl: add AXG compatible - dts: keep back HW order for MMC devices since change in Upstream Linux - Cleanup local AXG DT USB nodes now everything is upstream - distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot - New Boards: - Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge) - Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge) - Banana Pi M5: another credit card SBC - JetHub D1/H1: home automation controllers - Radxa Zero: another RPi Zero sized SBC
2021-10-07boards: amlogic: add Radxa Zero defconfigChristian Hewitt1-0/+65
Add a defconfig for the Radxa Zero SBC, using an Amlogic S905Y2 chip. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> [narmstrong: updated u200 MAINTAINERS & add missing CONFIG_SYS_LOAD_ADDR from defconfig] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07ARM: amlogic: add JetHub D1/H1 device supportVyacheslav Bocharov2-0/+134
Add support for new home automation devices. JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features: - DIN Rail Mounting case - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz - no video out - 512Mb/1GB DDR3 - 8/16GB eMMC flash - 1 x USB 2.0 - 1 x 10/100Mbps ethernet - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2. - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. - 2 x gpio LEDS - GPIO user Button - 1 x 1-Wire - 2 x RS-485 - 4 x dry contact digital GPIO inputs - 3 x relay GPIO outputs - DC source with a voltage of 9 to 56 V / Passive POE JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features: - Square plastic case - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz - no video out - 1GB DDR3 - 8/16GB eMMC flash - 2 x USB 2.0 - 1 x 10/100Mbps ethernet - WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0. - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. - MicroSD 2.x/3.x/4.x DS/HS cards. - 1 x gpio LED - ADC user Button - DC source 5V microUSB with serial console Patches from: - JetHub H1 https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607 - JetHub D1 https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79 Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> [narmstrong: removed unused variable value] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07ARM: amlogic: add Banana Pi M5Neil Armstrong1-0/+74
Banana Pi BPI-M5 is a credit card format SBC with the following features: - Amlogic S905X3 quad core Cortex-A55 - Mali-G31 GPU - 4GB LPDDR4 - 16GB eMMC flash - 4 USB 3.0 - 1 GbE ethernet - HDMI output - 2x LEDS - SDCard - 2.5mm Jack with Stereo Audio + CVBS - Infrared Received - ADC Button - GPIO Button - 40 pins header + 3pins debug header [narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07ARM: meson: add Beelink GS-King X boardNeil Armstrong1-0/+71
The Beelink GS-King X is a variant of the GS King boards but with an internal USB to SATA bridge and advanced audio features. [narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07ARM: amlogic: add support for Odroid-HC4 deviceNeil Armstrong1-0/+93
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge instead of the USB3 ports. [narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-10-07configs: enable SYSRESET_SBI on qemu-riscvXX_smode_defconfigHeinrich Schuchardt4-0/+4
There should be a platform compiled with the new driver. Enable CONFIG_SYSRESET_SBI for all QEMU boards using SBI. If you want to test the SBI sysreset driver, disable CONFIG_SYSRESET_SYSCON. Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
2021-10-06Convert CONFIG_NAND_OMAP_ECCSCHEME to KconfigWIP/2021-10-06-assorted-improvementsTom Rini15-0/+15
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we will use be a choice statement, enumerating the ones which we have implemented. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_SYS_NAND_U_BOOT_LOCATIONS et al to KconfigTom Rini58-1/+115
This converts the following to Kconfig: CONFIG_SYS_NAND_U_BOOT_LOCATIONS CONFIG_SYS_NAND_U_BOOT_OFFS Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_NAND_FSL_ELBC et al to KconfigTom Rini83-0/+83
This converts the following to Kconfig: CONFIG_NAND_FSL_ELBC CONFIG_NAND_FSL_IFC Note that a number of PowerPC platforms had previously enabled CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer enable the option, reducing the size of a few functions. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_SYS_NAND_ONFI_DETECTION to KconfigTom Rini166-0/+166
This converts the following to Kconfig: CONFIG_SYS_NAND_ONFI_DETECTION Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_SYS_NAND_5_ADDR_CYCLE to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_NAND_5_ADDR_CYCLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_SYS_NAND_PAGE_COUNT to KconfigTom Rini43-0/+43
This converts the following to Kconfig: CONFIG_SYS_NAND_PAGE_COUNT Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_SPL_NAND_LOAD et al to KconfigTom Rini72-0/+167
This converts the following to Kconfig: CONFIG_SPL_NAND_LOAD CONFIG_SYS_NAND_BLOCK_SIZE CONFIG_SYS_NAND_PAGE_SIZE CONFIG_SYS_NAND_OOBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-06Convert CONFIG_NAND_LPC32XX_MLC to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_NAND_LPC32XX_MLC Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-05lib: optee: Remove CONFIG_OPTEE_LOAD_ADDRAlexandru Gagniuc1-1/+0
This value is not used by u-boot, and it should not. The load address of an OPTEE image is defined by said image. Either a uImage or a FIT will have a defined load address and entry point. Those values are the correct ones, not CONFIG_OPTEE_LOAD_ADDR. Commit f25006b96e9f ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies this config by requiring its presence in u-boot's .config for other images as part of a larger build, claiming it is "the best way". This argument is not persuasive. U-boot's configuration is driven by platform requirements, not the other way around. It seems more likely that the argument is conflating tooling issues with Kconfig. Yocto and buildroot have excellent mechanisms for defining values across the board (pun intended). u-boot's Kconfig is the wrong place to do it. Furthermore, it is not "best" for u-boot because it hardcodes a value which is then not used. In fact the load address that u-boot uses is the one derived from the OPTEE image. Confused yet? I sure was. To prevent future confusion, remove CONFIG_OPTEE_LOAD_ADDR. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2021-10-05lib: optee: Remove CONFIG_OPTEE_TZDRAM_BASEAlexandru Gagniuc2-2/+0
It is no longer used in u-boot. Information about the TZDRAM location is usually available in the devicetree as "/reserved-memory/" nodes. Because this isn't used, remove it. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
2021-10-05lib: optee: remove the duplicate CONFIG_OPTEEPatrick Delaunay3-3/+3
The configuration CONFIG_OPTEE is defined 2 times: 1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command 2- in drivers/tee/optee/Kconfig for support of OP-TEE driver. It is abnormal to have the same CONFIG define for 2 purpose; and it is difficult to managed correctly their dependencies. Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig to manage OPTEE image load in SPL. This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE) to test the availability of the OP-TEE driver. This patch cleans the configuration dependency with: - CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot - CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL - CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot - CONFIG_OPTEE_LIB (new) => support of OP-TEE library After this patch, the macro have the correct behavior: - CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported - CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-10-03iot2050: Enable watchdog support, but do not auto-start itJan Kiszka1-0/+6
This allows to use the watchdog in custom scripts but does not enforce that the OS has to support it as well. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-03board: siemens: Add support for SIMATIC IOT2050 devicesJan Kiszka1-0/+130
This adds support for the IOT2050 Basic and Advanced devices. The Basic used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS quad-core version. Both variants are booted via a Siemens-provided FSBL that runs on the R5 cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot SPL, ATF and TEE have to reside in SPI flash. Full integration into a bootable image can be found on https://github.com/siemens/meta-iot2050 Based on original board support by Le Jin, Gao Nian and Chao Zeng. Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
2021-10-01ppc: Remove MPC8349EMDS board and ARCH_MPC8349 supportTom Rini4-522/+0
This board has not been converted to CONFIG_DM by the deadline. Remove it. Cc: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01arm: Remove bg0900 boardTom Rini1-43/+0
This board has not been converted to CONFIG_DM by the deadline. Remove it. Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01arm: Remove zmx25 board and ARCH_MX25Tom Rini1-38/+0
This board has not been converted to CONFIG_DM by the deadline. Remove it. As this is the last ARCH_MX25 platform, remove those references as well. Cc: Matthias Weisser <weisserm@arcor.de> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01arm: Remove aspenite boardTom Rini1-19/+0
This board has not been converted to CONFIG_DM by the deadline. Remove it. As this is the last armada100 platform, remove that support as well. Cc: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-01arm: Remove flea3 boardTom Rini1-58/+0
This board has not been converted to CONFIG_DM by the deadline. Remove it. As this is the last mx35 platform, remove that support as well. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Stefano Babic <sbabic@denx.de>
2021-09-30Merge tag 'xilinx-for-v2022.01-rc1' of ↵Tom Rini1-0/+6
https://source.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2022.01-rc1 zynq: - Enable capsule update for qspi and mmc - Update zed DT qspi compatible string zynqmp: - Add missing modeboot for EMMC - Add missing nand DT properties - List all eeproms for SC on vck190 - Add vck190 SC psu_init clk: - Handle only GATE type clock for Versal watchdog: - Update versal driver to handle system reset
2021-09-30ARM: zynq: Enable capsule update for qspi and mmcMichal Simek1-0/+6
Generate dfu_alt_info setup at runtime for capsule update. Enabling this feature will help with upgrading boards without remembering what is where. The similar change was done for ZynqMP by commit b86f43de0be0 ("xilinx: zynqmp: Add support for runtime dfu_alt_info setup"). Code needs to be enabled by CONFIG_SET_DFU_ALT_INFO. And also enable capsule on disk for RAW firmware images with efidebug command. Two indexes are supported for SPL flow. Images can be generated like: ./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin ./tools/mkeficapsule --raw u-boot.img --index 2 capsule2.bin Then place them to SD card and load them: load mmc 0 10000000 capsule1.bin && efidebug capsule update -v 10000000 load mmc 0 10000000 capsule2.bin && efidebug capsule update -v 10000000 FSBL flow will also work where only index 1 capsule is used. There should be enough space for using boot.bin with bitstream too. Zynq also support multiple boot locations in SPI or MMC but it is not wired by this patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/bea5fc75a87a5971f118b46bab4aa7ca39a629c6.1630061610.git.michal.simek@xilinx.com
2021-09-27Convert CONFIG_OMAP_EHCI_PHY1_RESET_GPIO et al to KconfigTom Rini6-0/+16
This converts the following to Kconfig: CONFIG_OMAP_EHCI_PHY1_RESET_GPIO CONFIG_OMAP_EHCI_PHY2_RESET_GPIO CONFIG_OMAP_EHCI_PHY3_RESET_GPIO To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO options to get setting the GPIO number. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-27Convert CONFIG_USB_XHCI_OMAP to KconfigTom Rini12-0/+12
This converts the following to Kconfig: CONFIG_USB_XHCI_OMAP Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-27usb: phy: ti: Remove non-DM PHY codeTom Rini6-6/+0
At this point in time, all platforms that had previously used drivers/usb/phy/omap_usb_phy.c have been migrated to DM and related options. Remove this now unused code and some related unused defines. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-27Merge tag 'dm-pull-next-27sep21' of ↵WIP/27Sep2021-nextTom Rini2-0/+4
https://source.denx.de/u-boot/custodians/u-boot-dm into next Various of-platdata improvements, including CONFIG_OF_REAL
2021-09-27Merge tag 'v2021.10-rc5' into nextTom Rini12-2/+34
Prepare v2021.10-rc5
2021-09-25dm: gpio: Add of-platdata supportSimon Glass2-0/+4
Add support for accessing GPIOs using of-plata. This uses the same mechanism as for clocks, but allows use of the xlate() method so that the driver can interpret the parameters. Update the condition for GPIO_HOG so that it is not built into SPL, since it needs SPL_OF_REAL which is not enabled in sandbox_spl. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-24vexpress_ca9x4: Add missing SYS_LOAD_ADDRTom Rini1-13/+10
- Add missing CONFIG_SYS_LOAD_ADDR based on other platforms - Resync Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-24ARM: vexpress_ca9x4: Reintroduce board in order to use with QEMU.Kristian Amlie1-0/+49
vexpress_ca9x4 is seemingly the only board except for qemu_arm which is able to run U-Boot correctly, using the `-M vexpress-a9` option to QEMU. Building for qemu_arm and running qemu-system-arm with the `-M virt` argument has a number of downsides, most importantly that it only supports virtio storage drivers. This significantly reduces its usefulness in testing memory card and Flash solutions, especially when the tested images are from a third party source. So therefore we reintroduce the vexpress_ca9x4 board in this commit, with the explicit goal of using it with QEMU. A number of differences to note from the original: * Since the board was apparently unmaintained, I have now set myself as the maintainer. * The board has been converted to use the driver model, which was the reason it was removed in the first place. * The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed in the same commit, are not necessary for the QEMU use case, and have been omitted. * An `mmc0` alias was introduced in the dts file. The mmc is not detected correctly without this, now that it's based on the device tree instead of the board's init function. * A couple of other nodes were removed because they were problematic when trying to run the UEFI bootmgr. Once again, the primary use case here is QEMU, and these nodes are not needed for that to work. * Unnecessary board init code has been removed, thanks to driver model and device tree. * `CONFIG_OF_EMBED` has been enabled. I know this goes against recommended practice, but there doesn't seem to be any other way to pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument does not work, I suppose because U-Boot doesn't use the same mechanics as the kernel when it's booting. * Load addresses have been changed to fit QEMU use case. People wanting to get a more detailed, yet somewhat isolated, diff between this and the original, can run this command: git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \ $( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD) (Make sure to either check out this commit first, or replace HEAD with the commit ID of this commit) Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
2021-09-23Merge git://source.denx.de/u-boot-socfpgaWIP/23Sep2021Tom Rini1-2/+6
Bugfixes for this one socfpga platform
2021-09-22Merge tag 'u-boot-at91-2022.01-a' of ↵Tom Rini7-1/+125
https://source.denx.de/u-boot/custodians/u-boot-at91 into next First set of u-boot-at91 features for the 2022.01 cycle: This feature set includes : the support for CPU driver for arm926 (sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp; starting to remove old Kconfig unused symbols from config_whitelist.txt (work will take more time); also small fixes and updates in mach, DT, configs, etc.
2021-09-22arm: socfpga: vining: Enable DW I2C driverMarek Vasut1-0/+1
The Designware I2C IP is used to communicate with I2C peripherals on SoCFPGA, and required to access I2C EEPROM on this board. Enable it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-22arm: socfpga: vining: Set default SPI NOR mode and frequencyMarek Vasut1-0/+3
The SPI NOR bus mode is 0 on this system, update it accordingly. Increase frequency to 40 MHz and enable SFDP parsing, since the flashes on this system support that and it is a huge performance improvement. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-22arm: socfpga: vining: Set USB gadget manufacturer to Softing with capital SMarek Vasut1-1/+1
This was configured in downstream, so it is likely that most of the custom software used around the device depends on it. Make upstream compatible. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-22arm: socfpga: vining: Increase environment sizeMarek Vasut1-1/+1
Increase the environment size from 4k to 16k to prevent environment from becoming full. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com>
2021-09-22configs: Enable USB3 on Allwinner H6 boardsSamuel Holland2-0/+10
Pine H64 and Orange Pi 3 both provide a USB3 type A port. Enable it in U-Boot. Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-09-21board: atmel: sama7g5ek: avoid rewriting of configured CONFIG_BOOTCOMMANDEugen Hristev2-0/+4
Rewrite the CONFIG_BOOTCOMMAND only if it's not previously configured from defconfig file. This allows the user to select from defconfig/menuconfig the desired boot command. Adjust the current board defconfigs to reflect the default booting command for the specific ENV configuration. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-09-21configs: sama5d2: add qspi config for QSPI1Mihai Sain1-0/+103
Add new config for storing environment from QSPI1. Signed-off-by: Mihai Sain <mihai.sain@microchip.com> [eugen.hristev@microchip.com: cleanup and add MAINTAINERS entry] Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2021-09-21configs: gardena-smart-gateway-at91sam: Adjust to production valuesReto Schneider1-1/+14
This commit updates the default config with the values that will be used soon on the Atmel / Microchip AT91SAM9G25 based GARDENA smart gateway. Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com> Reviewed-by: Stefan Roese <sr@denx.de>
2021-09-21configs: sam9x60ek: enable CONFIG_CPUClaudiu Beznea3-0/+3
Enable CONFIG_CPU for SAM9X60EK configs. Reported-by: Eugen Hristev <eugen.hristev@microchip.com> Fixes: a64862284f65 ("clk: at91: sam9x60: add support compatible with CCF") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2021-09-16Merge tag 'v2021.10-rc4' into nextTom Rini40-99/+52
Prepare v2021.10-rc4 Signed-off-by: Tom Rini <trini@konsulko.com> # gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT # gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C # gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate] # Conflicts: # board/Arcturus/ucp1020/spl.c # cmd/mvebu/Kconfig # common/Kconfig.boot # common/image-fit.c # configs/UCP1020_defconfig # configs/sifive_unmatched_defconfig # drivers/pci/Kconfig # include/configs/UCP1020.h # include/configs/sifive-unmatched.h # lib/Makefile # scripts/config_whitelist.txt
2021-09-15configs: rpi: Enable SMBIOS sysinfo driverMatthias Brugger9-0/+18
Enable this driver to allow U-Boot to get SMBIOS table information from a device tree node. Signed-off-by: Matthias Brugger <mbrugger@suse.com> Acked-by: Fabian Vogt <fvogt@suse.com>
2021-09-14configs: Resync with savedefconfigTom Rini26-31/+5
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-13ppc: Remove UCP1020 boardSimon Glass1-58/+0
This board has not been converted to CONFIG_DM_PCI by the deadline. Remove it. Note that we have to add CONFIG_SPIFLASH to scripts/config_whitelist.txt because it's not really migrated at this point. Acked-by: Michael Durrant <mdurrant@arcturusnetworks.com> Acked-by: Oleksandr Zhadan <oleks@arcturusnetworks.com> Acked-by: Oleksandr Zhadan and Michael Durrant <arcsupport@arcturusnetworks.com> Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Handle CONFIG_SPIFLASH differently and delete Kconfig file] Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.1 at 2024-08-02 19:27:03 +0000