aboutsummaryrefslogtreecommitdiff
path: root/configs/pico-imx7d_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2019-01-10Kconfig: rename CONFIG_SPL_USB_GADGET_SUPPORT as CONFIG_SPL_USB_GADGETJean-Jacques Hiblot1-1/+1
The SPL option for USB gadget should be named after the option for u-boot (CONFIG_USB_GADGET) Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-01-07configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-09pico-imx7d: Make SPL binary fit into 64kBFabio Estevam1-1/+0
Currently SPL binary is larger than 64kB, which is larger than CONFIG_SPL_MAX_SIZE defined in imx7_spl.h. This causes boot failure on the pico-mx7 targets. Remove CONFIG_SPL_LIBDISK_SUPPORT option for now, so that the SPL binary can fit into the 64kB range. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford1-0/+1
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini1-0/+1
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-23pico-imx7d: Enable auxiliary code supportOtavio Salvador1-0/+1
This enables the "bootaux" command so a firmware can be loaded inside the M4 MCU. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Allow default fdtfile to be overridden by defconfigOtavio Salvador1-0/+1
This allow the addition of extra default configurations for each baseboard, removing the boot menu when user boots for the first time. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Enable CONFIG_ARMV7_BOOT_SEC_DEFAULTFabio Estevam1-0/+1
Currently the CAAM driver fails to be probed: caam 30900000.caam: Entropy delay = 3200 caam 30900000.caam: failed to acquire DECO 0 caam 30900000.caam: failed to instantiate RNG CAAM needs to be initialized in secure world, so enable CONFIG_ARMV7_BOOT_SEC_DEFAULT to allow the driver to probe successfully. Tested with kernel mainline version 4.17.2. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add Falcon mode supportFabio Estevam1-0/+2
Falcon mode boots the kernel directly from SPL, without loading the full U-Boot. As pico-imx7d does not have a GPIO for selecting Falcon versus normal mode, enter in Falcon mode when the customer selects the CONFIG_SPL_OS_BOOT option in menuconfig. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add bootmenu to choose the baseboardOtavio Salvador1-1/+2
Currently the baseboards do not offer a way to autodetect which one is in use, so we ask the user if no value has been set. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add SPL supportFabio Estevam1-1/+13
Convert pico-imx7d to SPL support. There are two variants of pico-imx7d SOMs: - One with 512MB of RAM - One with 1GB of RAM The 512MB module contains two Hynix H5TC2G63GFR-PBA. The 1GB module contains two Hynix H5TC4G63GFR-PBA. The RAM size is determined in runtime by reading GPIO1_12. While at it, also add USB Serial Download mode support as it is very helpful for loading SPL and u-boot.img via imx_usb_loader. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add fastboot supportFabio Estevam1-1/+6
fastboot tool is a convenient way to flash the eMMC, so add support for it. Examples of usages: On the pico-imx7d U-Boot prompt: => fastboot 0 On the Linux PC connected via USB: 1. Retrieving the U-Boot version $ sudo fastboot getvar bootloader-version -i 0x0525 bootloader-version: U-Boot 2018.07-rc1-03888-gde846f9 finished. total time: 0.000s 2. Resetting the board $ sudo fastboot reboot -i 0x0525 (this causes the pico-imx7d to reboot) Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add default DFU targetsOtavio Salvador1-1/+2
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Add GPT partitioning supportOtavio Salvador1-1/+1
This allow the use of: > run setup_emmc inside of the U-Boot prompt to do the partitioning of the disk. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-07-23pico-imx7d: Fix common distro configuration behaviorOtavio Salvador1-8/+5
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid` environment helper to allow it to properly work with Yocto Project and other distributions using extlinux autogenerated configuration files. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2018-04-17configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15Merge git://git.denx.de/u-boot-imxTom Rini1-0/+1
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-15pico-imx7d: Replace fatload commandVanessa Maegima1-0/+1
Replace fatload with the fs generic loading interface ('load' command). Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-08treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six1-0/+1
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini1-0/+1
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-10cmd: Toggle the default value of CONFIG_CMD_IMLSTuomas Tynkkynen1-1/+0
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-03usb: gadget: Make g_dnl USB settings commonMaxime Ripard1-3/+3
The g_dnl USB settings for the vendor ID, product ID and manufacturer are actually common settings that can and should be shared by all the gadgets. Make them common by renaming them, and convert all the users. Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-08-14configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-07Move PHYLIB to KconfigAlexandru Gagniuc1-0/+1
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-07-10configs: Resync defconfigsTom Rini1-4/+4
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-31pico-imx7d: Add initial supportVanessa Maegima1-0/+35
Add the initial support for pico-imx7d board based on Wig Cheng's source code. Add support for eMMC, USB gadget, I2C, PMIC and Ethernet. For more information about this board, please visit: http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
generated by cgit v1.1 at 2024-07-13 05:29:54 +0000