Age | Commit message (Collapse) | Author | Files | Lines |
|
This converts the following to Kconfig:
CONFIG_SCSI_AHCI_PLAT
CONFIG_SYS_SCSI_MAX_SCSI_ID
CONFIG_SYS_SCSI_MAX_LUN
CONFIG_SYS_SATA_MAX_DEVICE
Drop CONFIG_SCSI for everything except the sandbox build. We only need
one build for tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_REMAKE_ELF
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
|
|
The initial patch had typos that caused four defconfigs to miss the
symbol transition to Kconfig. CONFIG_SYS_QE_FW_ADDR and
CONFIG_SYS_FMAN_FW_ADDR are currently initialized to 0 by default
on these builds, which prevents the firmware from loading.
Add the correct symbols to these defconfigs.
Fixes: a97a071d10d2b ("configs: fsl: migrate FMAN/QE specific defines to Kconfig")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_CONS_INDEX
CONFIG_DEBUG_UART_CLOCK
CONFIG_FSL_TZPC_BP147
CONFIG_GENERIC_ATMEL_MCI
CONFIG_IDENT_STRING
CONFIG_LIBATA
CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
CONFIG_LPC32XX_GPIO
CONFIG_MP
CONFIG_MPC8XXX_GPIO
CONFIG_MTD_PARTITIONS
CONFIG_MVGBE
CONFIG_MXC_GPIO
CONFIG_NR_DRAM_BANKS
CONFIG_OF_BOARD_SETUP
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_OF_SYSTEM_SETUP
CONFIG_PREBOOT
CONFIG_ROCKCHIP_SERIAL
CONFIG_RTC_ENABLE_32KHZ_OUTPUT
CONFIG_RTC_MV
CONFIG_SCSI_AHCI
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_SPEED
CONFIG_SOFT_SPI
CONFIG_SPI_FLASH_EON
CONFIG_SPI_FLASH_MACRONIX
CONFIG_SPI_FLASH_MTD
CONFIG_SPI_FLASH_SPANSION
CONFIG_SPI_FLASH_SST
CONFIG_SPI_FLASH_STMICRO
CONFIG_SUPPORT_RAW_INITRD
CONFIG_SYS_ARCH_TIMER
CONFIG_SYS_BOARD
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
CONFIG_SYS_DCACHE_OFF
CONFIG_SYS_FDT_SAVE_ADDRESS
CONFIG_SYS_FLASH_CFI
CONFIG_SYS_FSL_ERRATUM_ESDHC135
CONFIG_SYS_HAS_SERDES
CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_LITTLE_ENDIAN
CONFIG_SYS_LOAD_ADDR
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
CONFIG_SYS_NS16550
CONFIG_SYS_PLLFIN
CONFIG_SYS_SPI_U_BOOT_OFFS
CONFIG_TIMER_SYS_TICK_CH
CONFIG_USB_EHCI_FSL
CONFIG_U_QE
CONFIG_VERSION_VARIABLE
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_NAND_ONFI_DETECTION
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Prepare v2021.10-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
# gpg: Signature made Tue 14 Sep 2021 06:58:32 PM EDT
# gpg: using RSA key 1A3C7F70E08FAB1707809BBF147C39FF9634B72C
# gpg: Good signature from "Thomas Rini <trini@konsulko.com>" [ultimate]
# Conflicts:
# board/Arcturus/ucp1020/spl.c
# cmd/mvebu/Kconfig
# common/Kconfig.boot
# common/image-fit.c
# configs/UCP1020_defconfig
# configs/sifive_unmatched_defconfig
# drivers/pci/Kconfig
# include/configs/UCP1020.h
# include/configs/sifive-unmatched.h
# lib/Makefile
# scripts/config_whitelist.txt
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_POWER_I2C
CONFIG_POWER_LEGACY
They are handled at the same time due to a dependency between them.
Update the Makefile rule to use legacy power only in U-Boot proper.
Unfortunately a separate rule is needed in SPL to be able to build
legacy power. Add SPL related symbols for both, to allow for SPL-only
usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: More SPL related cleanups, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
|
|
This converts the following to Kconfig:
CONFIG_RAMBOOT_PBL
CONFIG_SYS_FSL_PBL_PBI
CONFIG_SYS_FSL_PBL_RCW
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Guard most of the options in drivers/ddr/fsl/Kconfig with
SYS_FSL_DDR || SYS_FSL_MMDC.
- Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER
to Kconfig.
- Clean up the logic for including the DDR_ECC_CMD code.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_I2C_SET_DEFAULT_BUS_NUM
CONFIG_I2C_DEFAULT_BUS_NUMBER
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_SYS_I2C_MXC
CONFIG_SYS_I2C_MXC_I2C1
CONFIG_SYS_I2C_MXC_I2C2
CONFIG_SYS_I2C_MXC_I2C3
CONFIG_SYS_I2C_MXC_I2C4
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The optical 10G port is described as fixed-link in the device tree. Enable
the necessary support.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so
remove that.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
As it has been now two years past the migration deadline, it is required
to have migrated. Remove the check from the Makefile and rework some of
the Kconfig logic slightly to get the functional dependencies of DM_MMC
/ BLK right in both the SPL and non-SPL case.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Drop CONFIG_DM_I2C undefs from board header files, and make them
disabled on these boards in defconfigs instead.
Disabling on Kconfig symbol was done automatically with this script:
cd configs
files=(*ls1046a*)
files2=(*T104*RDB*)
files3=(ls1021atwr_*)
files4=("imx8mp_evk_defconfig phycore-imx8mp_defconfig")
combine=("${files[@]}" "${files2[@]}" "${files3[@]}" "${files4[@]}")
cd ..
for item in ${combine[*]}
do
echo "Adjusting $item"
echo "# CONFIG_SPL_DM_I2C is not set" >> configs/$item
make $item && make savedefconfig && cp defconfig configs/$item
done
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable CMD_GPIO for board ls1046ardb
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape
platforms
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
CONFIG_ENV_OVERWRITE disables write protection on various environment
variables like "ethaddr" and "serial".
Enable this config in LS1046A and LS1012A defconfigs. This resolves an
error while setting multiple values of "ethaddr" variable.
Before the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Error: Can't overwrite "ethaddr"
Error inserting "ethaddr" variable, errno=1
After the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
|
|
Enable DM_ETH on all the defconfigs for the LS1046ARDB board.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
- Finish migration of CONFIG_PHYLIB and a number of related symbols to
defconfig files.
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This converts the following to Kconfig:
CONFIG_PHYLIB
CONFIG_BITBANGMII
CONFIG_MV88E6352_SWITCH
CONFIG_MV88E61XX_SWITCH
CONFIG_PHYLIB_10G
CONFIG_PHY_AQUANTIA
CONFIG_PHY_ATHEROS
CONFIG_PHY_BROADCOM
CONFIG_PHY_CORTINA
CONFIG_PHY_DAVICOM
CONFIG_PHY_ET1011C
CONFIG_PHY_LXT
CONFIG_PHY_MARVELL
CONFIG_PHY_MICREL
CONFIG_PHY_NATSEMI
CONFIG_PHY_REALTEK
CONFIG_RTL8211X_PHY_FORCE_MASTER
CONFIG_PHY_SMSC
CONFIG_PHY_TERANETICS
CONFIG_PHY_TI
CONFIG_PHY_VITESSE
CONFIG_PHY_XILINX
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|