aboutsummaryrefslogtreecommitdiff
path: root/configs/ls1021atwr_nor_lpuart_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2021-12-27Convert CONFIG_CONS_INDEX et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01Convert CONFIG_USE_BOOTCOMMAND et al to KconfigTom Rini1-1/+1
This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-12configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-09configs: fsl: migrate FMAN/QE specific defines to KconfigRajesh Bhagat1-0/+1
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR, CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and move these entries to defconfigs. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-11-01configs: Resync with savedefconfigWIP/01Nov2021Tom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31Convert CONFIG_SKIP_LOWLEVEL_INIT et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_SKIP_LOWLEVEL_INIT CONFIG_SKIP_LOWLEVEL_INIT_ONLY In order to do this, we need to introduce SPL and TPL variants of these options so that we can clearly disable these options only in SPL in some cases, and both instances in other cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31Convert CONFIG_SYS_LOAD_ADDR to KconfigTom Rini1-0/+1
Now that we have consistent usage, migrate this symbol to Kconfig. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-30Convert CONFIG_I2C_SET_DEFAULT_BUS_NUM et al to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_I2C_SET_DEFAULT_BUS_NUM CONFIG_I2C_DEFAULT_BUS_NUMBER Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_MXC et al to KconfigTom Rini1-0/+3
This converts the following to Kconfig: CONFIG_SYS_I2C_MXC CONFIG_SYS_I2C_MXC_I2C1 CONFIG_SYS_I2C_MXC_I2C2 CONFIG_SYS_I2C_MXC_I2C3 CONFIG_SYS_I2C_MXC_I2C4 Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini1-0/+1
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to KconfigTom Rini1-0/+2
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30Convert CONFIG_ID_EEPROM to KconfigTom Rini1-0/+1
This converts the following to Kconfig: CONFIG_ID_EEPROM Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-26configs: Resync with savedefconfigTom Rini1-2/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07configs: Remove unnecessary CONFIG_DM_PCI_COMPAT=yTom Rini1-1/+0
The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so remove that. Signed-off-by: Tom Rini <trini@konsulko.com>
2021-05-11configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-15configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-08configs: ls1021atwr: enable CMD_GPIOBiwen Li1-0/+1
Enable CMD_GPIO for ls1021atwr Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-11-30configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-29configs: Resync with savedefconfigTom Rini1-7/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-29Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini1-0/+2
- Bug fixes and updates on vid, ls1088a lx2160a and other layerscape platforms. - Add optee_rpmb support for LX2 & Kontron sl28 support
2020-10-26ls1021atwr: disable obsolete VIDEO configAnatolij Gustschin1-2/+2
DM_VIDEO conversion deadline has passed, disable VIDEO config. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-10-23configs: Enable NVME support for Layerscape platformsWasim Khan1-0/+2
Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape platforms Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24configs: enable DM_MDIO for LS1021A-TWR and LS1021A-TSNVladimir Oltean1-0/+1
The tsec driver now requires DM_MDIO when DM_ETH is enabled. To avoid build errors, enable DM_MDIO in these boards' configs before we actually add DM_MDIO support to tsec. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-08-10configs: Resync with savedefconfigv2020.10-rc2Tom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28Convert CONFIG_ENV_OVERWRITE to KconfigAdam Ford1-0/+1
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-27pci: layerscape: Add specific config entry for RC and EP mode driverHou Zhiqiang1-1/+1
Add Root Complex and Endpoint mode specific config entries, such that it's feasible to enable the RC and/or EP mode driver indepently. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-08treewide: mem: Move mtest related defines to KconfigAshok Reddy Soma1-0/+2
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-06configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-02-04dm: arm: ls1021a: add i2c DM supportBiwen Li1-0/+2
This supports i2c DM and enables CONFIG_DM_I2C for SoC LS1021A Signed-off-by: Biwen Li <biwen.li@nxp.com> Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-01-22configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-03mtd: rename CONFIG_MTD_DEVICE -> CONFIG_MTDMiquel Raynal1-0/+1
Like in Linux, just use CONFIG_MTD to compile the MTD stack. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini1-0/+3
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-08-14configs: Resync with savedefconfigTom Rini1-2/+2
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-25arm: ls1021atwr: Convert to use driver model TSEC driverBin Meng1-0/+2
Now that we have added driver model support to the TSEC driver, convert ls1021atwr board to use it. This depends on previous DM series for ls1021atwr: http://patchwork.ozlabs.org/patch/561855/ Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> [Vladimir] Made the following changes: - Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi - Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 - a mistake ported over from Linux. Each SGMII PCS lies on the private MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS). - Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs - Completely removed non-DM_ETH support from ls1021atwr - Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio" and from "fsl,tsec" to "fsl,etsec2" to match Linux
2019-04-29configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-02-19configs: ls1021a: enable sata configs for all ls1021a defconfigsPeng Ma1-0/+3
Add CONFIG_AHCI CONFIG_SATA_CEVA CONFIG_DM_SCSI for some ls1021a defconfigs that missing one of them or more. enable CONFIG_DM_MMC for some defconfigs to support CONFIG_BLK Support sata for all ls1021a defconfigs Signed-off-by: Peng Ma <peng.ma@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-01-07configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19Convert CONFIG_FLASH_CFI_DRIVER et al to KconfigAdam Ford1-2/+4
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-27Enable CONFIG_BLK and CONFIG_DM_MMC to KconfigYinbo Zhu1-0/+2
This enables the folowing to Kconfig: CONFIG_BLK CONFIG_DM_MMC Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-09-03configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MISC_INIT_R to KconfigAdam Ford1-0/+1
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17Convert CONFIG_MII et al to KconfigAdam Ford1-1/+1
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-16configs: Migrate CONFIG_NR_DRAM_BANKSTom Rini1-0/+1
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08treewide: Migrate CONFIG_FSL_ESDHC to KconfigMario Six1-0/+1
Migrate the CONFIG_FSL_ESDHC option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-08treewide: Migrate CONFIG_TSEC_ENET to KconfigMario Six1-1/+1
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-23configs: Re-sync with CONFIG_DISTRO_DEFAULTSTom Rini1-7/+2
A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11configs: Migrate CONFIG_SYS_TEXT_BASETom Rini1-0/+1
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-30configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.1 at 2024-08-03 10:09:39 +0000