aboutsummaryrefslogtreecommitdiff
path: root/configs/elgin-rv1108_defconfig
AgeCommit message (Collapse)AuthorFilesLines
2021-06-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-16rockchip: rv1108: enable board early initKever Yang1-0/+1
Enable board early init callback to init board specific hardware. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-08-10configs: Resync with savedefconfigv2020.10-rc2Tom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-03-26elgin-rv1108: Avoid adc_channel_single_shot errorOtavio Salvador1-0/+1
Currently the following error message is seen during boot: U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300) Model: Elgin RV1108 R1 board DRAM: 128 MiB APLL: 600000000 DPLL:1200000000 GPLL:1188000000 ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000 MMC: dwmmc@30110000: 0 Loading Environment from MMC... OK In: serial@10210000 Out: serial@10210000 Err: serial@10210000 Model: Elgin RV1108 R1 board rockchip_dnl_key_pressed: adc_channel_single_shot fail! .... Since the elgin-rv1108 does not use ADC to read the download key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid such error. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-03-26elgin-rv1108: Use rk_board_late_init() for GPIO settingsOtavio Salvador1-0/+1
Since commit 8e9a8d0d0c8c ("rockchip: elgin-rv1108: use board_early_init_f for per-boar init") the function that configure the board GPIOs is no longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected. These GPIOs do not need to be configured in such early stagem, so change it to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y to fix the regression. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-01-22configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04configs: Resync with savedefconfigTom Rini1-2/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-23Merge tag 'u-boot-rockchip-20191124' of ↵Tom Rini1-2/+0
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - Clean vid/pid in Kconfig and add fastboot for rk3399 - add 'u-boot, spl-fifo-mode' for mmc - Use FIT generator for rk3229 optee and rk3368 ATF - fan53555: add support for Silergy SYR82X and SYR83X
2019-11-23gadget: Select USB_GADGET_VENDOR_NUM for rockchipJagan Teki1-1/+0
Gadget vendor number, 0x2207 is common across all platfroms supported in Rockchip SoC. So, select the same number globally, if ARCH_ROCKCHIP. This eventually drop the explicit configs defined in supported board defconfig files. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-23gadget: Select USB_GADGET_MANUFACTURER for rockchipJagan Teki1-1/+0
Select the gadget manufacturer as 'Rockchip' for all rockchip platform SoC's. This eventually drop the explicit defined added on supported board defconfig files. Tested-by: Levin Du <djw@t-chip.com.cn> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2019-11-20env: Finish migration of common ENV optionsTom Rini1-0/+1
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbolTom Rini1-0/+1
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29configs: Resync with savedefconfigTom Rini1-1/+1
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07configs: Resync with savedefconfigTom Rini1-1/+0
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-16ARM: rockchip: Add rv1108-elgin-r1 board supportOtavio Salvador1-0/+58
Add the initial support for Elgin R1 board, which is based on the RV1108 SoC and has the following features currently supported in U-Boot: - UART - eMMC - USB Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
generated by cgit v1.1 at 2024-07-13 15:12:49 +0000