aboutsummaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)AuthorFilesLines
2017-10-01rockchip: rk3399-puma: add boot-on regulator to override BIOS_DISABLEPhilipp Tomsich1-0/+10
The (Qseven) BIOS_DISABLE signal on the RK3399-Q7 (Puma) keeps the eMMC and SPI in reset initially and we need to write a GPIO to turn them on before continuing the boot-up. This adds the DTS entries for the additional regulator and makes pinctrl and gpio3 available during SPL. It also adds a hook to the spl_board_init() to ensure that the regulator gets probed and enabled. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01rockchip: puma-rk3399: update board_init()Philipp Tomsich1-32/+4
The original initialisation code for board_init() was largely lifted from the code on the EVB. However, the RK3399-Q7 can do with a much more concise init sequence. This cleans up the board_init() by updating it to the essentials for the RK3399-Q7 and getting rid of the accumulated cruft. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01rockchip: rk3399: make spl_board_init board-specificPhilipp Tomsich2-6/+36
The later-stage spl_board_init (as opposed to board_init_f) should set up board-specific details: these differ between the EVB-RK3399 and the RK3399-Q7 (Puma). This moves spl_board_init back into the individual boards and removes the unneeded functionality from Puma. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-10-01rockchip: board: lion-rk3368: avoid ATF overwriting active SPL stagePhilipp Tomsich1-2/+2
The RK3368-uQ7 ATF has been moved back to 0x100000 (1MB from the start of DRAM) to avoid it overwriting the active SPL stage during FIT image loading. This change adapts the .its to match up (again) with our ATF repository for the RK3368-uQ7. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-10-01rk3288: vyasa: Add falcon mode supportJagan Teki1-0/+13
Add Falcon mode support in vyasa rk3288 board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-29ARM: omap3: am3517-evm: Add device tree and DM supportAdam Ford1-24/+47
With the device tree ported from Linux 4.13, this enables Driver Model and Device Tree support for the am3517-evm Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2017-09-29arm: da850-evm: Enable DM and device tree support for da850-evmAdam Ford2-1/+4
With the device tree ported and DM compatible drivers, enable: OF_CONTROL, DM_SPI, DM_SPI_FLASH and DM_SERIAL Note: DM_SERIAL is not enabled for da850evm_direct_nor_defconfig yet. Reviewed-by: Jagan Teki <jagan@openedev.com> Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-26arm: mvebu: clearfog: document boot from UARTBaruch Siach1-0/+20
Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26arm: mvebu: Remove theadorable_defconfigStefan Roese1-1/+0
Currently, we support 2 "theadorable" MVEBU build targets. One with a stripped down configuration (theadorable) and one with a full blown configuration (theadorable_debug), including PCI, ethernet etc. When we introduced these configs, the plan was to remove the debug version at some point. But now it seems better to keep the full-blown version and remove the "non-debug" version instead. At a later stage, I will rename the remaining "theadorable_debug" target into a more fitting one. Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-22board/ls2080ardb: Update board env based on SoCPriyanka Jain1-0/+12
As per current implementation, default value of board env is based on board filename i.e ls2080ardb. With distro support changes, this env is used to decide upon kernel dtb which is different for other SoCs (ls2088a, ls2081a) combination supported with this board. Add support to modify board env at runtime based on SoC type Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-22board: Add stm32h7 SoC, discovery and evaluation boards supportPatrice Chotard8-0/+179
This patch adds support for stm32h7 soc family, stm32h743 discovery and evaluation boards. For more information about STM32H7 series, please visit: http://www.st.com/en/microcontrollers/stm32h7-series.html Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-22board: STiH410-B2260: add fastboot supportPatrice Chotard1-0/+42
Add usb_gadget_handle_interrupts(), board_usb_init(), board_usb_cleanup() and g_dnl_board_usb_cable_connected() callbacks needed for FASTBOOT support Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-21nds32: board: Fix andestech adp-ae3xx.c make fail problem.rick1-0/+1
Add #include <asm/mach-types.h> to fix it. Signed-off-by: rick <rick@andestech.com>
2017-09-20Merge git://www.denx.de/git/u-boot-imxTom Rini19-74/+416
2017-09-20toradex: imx6: Move g_dnl_bind_fixup() into common SPL codeFabio Estevam2-26/+0
Instead of having every board file to add its own g_dnl_bind_fixup() implementation, move it to the common imx6 SPL code. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-09-20board: ge: bx50v3: set eth0 MAC addressIan Ray4-1/+363
Define i2c mux configuration. Add new vpd_reader which is used to read vital product data. Read VPD from EEPROM and set eth0 MAC address. Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Jose Alarcon <jose.alarcon@ge.com>
2017-09-20detect and setup solidrun hummingboard2Dennis Gilmore1-2/+33
The hummingboard2 is slightly different to the cubox i and to the hummingboard. The GPIO pin info to probe came from solidruns for of u-boot on github. https://github.com/SolidRun/u-boot-imx6/blob/imx6/board/solidrun/mx6_cubox-i/mx6_cubox-i.c#L569-L589 I have tested on a hummingboard-edge witha imx6 solo and 512mb of ram. Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
2017-09-18rockchip: puma_rk3399: increase serialno_str sizeKlaus Goger1-1/+1
Increase serialno_str to 17 bytes so it can hold the 16 bytes long serial nummer and the terminating null byte added by snprintf. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
2017-09-18rk3288: Add Vyasa initial board supportJagan Teki4-0/+32
This patch adds support for Vyasa RK3288 initial board from Amarula Solutions. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: board: puma_rk3399: update README flash instructionsKlaus Goger1-8/+43
Puma supports other boot sources then SD-Card. Update README to include the required steps. * how to package a SPI-NOR SPL * how to flash eMMC with rkdeveloptool Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18rockchip: board: lion_rk3368: update README flash instructionsKlaus Goger1-2/+22
Add a section to the README on how to flash the on-board eMMC with the rkdeveloptool. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-09-18imx6: drop duplicated bss memset and board_init_r() callAnatolij Gustschin8-42/+0
bss section is cleared in crt0.S. board_init_r() is also entered from crt0 code. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Christian Gmeiner <christian.gmeiner@gmail.com> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Marek Vasut <marex@denx.de> Cc: Lukasz Majewski <lukma@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-09-18pico-imx7d: Add "how to boot with NXP 4.1 Kernel"Vanessa Maegima1-0/+17
The NXP 4.1 kernel needs to boot with secure boot. Add information on how to enable secure boot mode. Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
2017-09-18imx: imx7d: remove CamelCase from ENET_xMHz macrosEric Nelson3-3/+3
Update these macros to use all upper-case to avoid checkpatch warnings: ENET_25MHz, ENET_50MHz, ENET_125MHz, Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-09-16x86: Support Intel Cherry Hill boardBin Meng6-0/+653
This adds support to Intel Cherry Hill board, a board based on Intel Braswell SoC. The following devices are validated: - serial port as the serial console - on-board Realtek 8169 ethernet controller - SATA AHCI controller - EMMC/SDHC controller - USB 3.0 xHCI controller - PCIe x1 slot with a graphics card - ICH SPI controller with an 8MB Macronix SPI flash - Integrated graphics device as the video console Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-15blk: Remove various places that do flush cache after readBin Meng1-2/+0
All these places seem to inherit the codes from the MMC driver where a FIXME was put in the comment. However the correct operation after read should be cache invalidate, not flush. The underlying drivers should be responsible for the cache operation. Remove these codes completely. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: York Sun <york.sun@nxp.com> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: York Sun <york.sun@nxp.com>
2017-09-14GPT: create block device for sandbox testingAlison Chaiken1-0/+5
Provide a Python function that creates a small block device for the purpose of testing the cmd/gpt.c or cmd/part.c functions in the u-boot sandbox. Signed-off-by: Alison Chaiken <alison@peloton-tech.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14arm: am57xx: cl-som-am57x: Use new pinctrl macrosSuman Anna1-52/+53
Commit 6ae4c3efbd62 ("ARM: DRA7: Add pinctrl register definitions") has added new macros for pinmux configuration in line with the kernel definitions. Fixup the current pinctrl data for the CompuLab CL-SOM-AM57x board to use these new macros to facilitate the removal of the old macros. NOTE: The PEN and PDIS macro values used previously were actually defined inversely, a value of 1 in bit position 16 actually means that the internal pullup/pulldown is disabled and not enabled as inferred by PEN. So, previous pinmux config data such as (PDIS | PTU) is confusing as it actually was meant for enabling internal pullup. The data is fixed up only to be equivalent to the previous data. Signed-off-by: Suman Anna <s-anna@ti.com>
2017-09-14configs: at91: Remove CONFIG_SYS_EXTRA_OPTIONS assignmentWenyou Yang8-14/+14
To remove the assignment of CONFIG_SYS_EXTRA_OPTIONS option, which is deprecated, use the CONFIG_XXXX_BOOT options to indicate the boot media, and the SoC is selected by the board. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
2017-09-14board: atmel: Add SAMA5D27 SOM1 EK boardWenyou Yang4-0/+218
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2 with 1Gbit DDR2-SDRAM in a single package. The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and Mac-address EEPROM. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14board: sama5d2_xplained: Make SPL work on spiflashWenyou Yang1-0/+10
Because before switching to a lower clock source, we must switch the clock source first instead of last. So before configuring the PMC_MCKR register, invoke at91_mck_init_down() first. As said in datasheet, the the size of SPL must not exceed the maximum size allowed(64Kbytes). Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-14atmel: common: Add function to display via DM_VIDEO's APIWenyou Yang2-0/+73
Add a function to display the company's logo and board information via the API from DM_VIDEO. This function can be shared by other atmel boards, so locate it in board/atmel/common folder. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-13ARM: davinci: Update da8xxevm MaintainersAdam Ford1-8/+2
The e-mail addresses for DA8XXEVM BOARD and DA850_AM18XXEVM BOARD are invalid. Remove DA8XXEVM. Update DA850_AM18XXEVM to have me be the maintainer since I work for Logic PD and have access to OMAP-L138 and AM1808 EVM kits. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-13Convert CONFIG_MAC_ADDR_IN_SPIFLASH et al to KconfigAdam Ford1-0/+24
This converts the following to Kconfig: CONFIG_MAC_ADDR_IN_SPIFLASH CONFIG_MAC_ADDR_IN_EEPROM Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-13davinci: da850evm: Make EEPROM MAC code configurableAdam Ford1-1/+4
There was a check for CONFIG_MAC_ADDR_IN_EEPROM and a check for CONFIG_MAC_ADDR_IN_SPIFLASH, however some of the EEPROM related code wasn't encapsulated inside the #if defined statement so the EEPROM code could get executed even when it wasn't explicitly enabled or wanted. Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-13omap3: omap3_logic: Finish enabling fastboot on MUSBAdam Ford1-0/+31
Either the USB and Fastboot were never finished, or somehow it got lost. This puts enough hooks back into omap3logic to enable fastboot and hopefully prepare it for Kconfig conversion. Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-12ARM: DRA72x: Add support for detection of DRA71x SR 2.1Vishal Mahaveer1-0/+3
DRA71x processors are reduced pin and software compatible derivative of DRA72 processors. Add support for detection of SR2.1 version of DRA71x family of processors. Signed-off-by: Vishal Mahaveer <vishalm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-12davinci: da850-evm: switch to using TI_COMMON_CMD_OPTIONSAdam Ford1-2/+2
Like the OMAP-L138 LCDK before it, let's move the da850-evm and the variations to TI_COMMON_CMD_OPTIONS to cut back one some of the defconfig entries. Signed-off-by: Adam Ford <aford173@gmail.com>
2017-09-12omap3: am3517_evm: Enable TI_COMMON_CMD_OPTIONAdam Ford1-0/+2
Enable TI_COMMON_CMD_OPTIONS and remove similar options from the defconfig. Updated with savedefconfig. Signed-off-by: Adam Ford <aford173@gmail.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2017-09-12ARM: k2g: Add FIT image handler for PMMC firmwareAndrew F. Davis1-0/+21
The PMMC firmware should be bundled into a FIT image on HS devices to allow authentication/decryption, add a handler to process this PMMC firmware. Signed-off-by: Andrew F. Davis <afd@ti.com>
2017-09-12Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini17-11/+1607
2017-09-12Merge git://git.denx.de/u-boot-dmTom Rini1-4/+3
2017-09-11sandbox: Convert SANDBOX_BITS_PER_LONG to KconfigBin Meng1-4/+3
Convert SANDBOX_BITS_PER_LONG to Kconfig and assign it a correct number depending on which host we are going to build and run. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: sama5d4_xplained: Set mac address from eepromWenyou Yang1-0/+12
Add the code to set the ethernet mac address from eeprom by using the common code from the common folder. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: sama5d2_xplained: Replace code to set mac addressWenyou Yang1-42/+4
Replace the code to set the ethernet mac address with the code from the common folder. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: atmel: Create board/$(VENDOR)/common folderWenyou Yang3-0/+59
Create board/$(VENDOR)/common folder to accommodate the common code shared by other atmel boards, now put the code to set ethernet mac address from eeprom, which uses the i2c eeprom driver. Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-09-11board: ti: am57xx: Add dt support for BeagleBoard-X15 revCLokesh Vutla1-0/+3
Add support for selecting proper dtb for am57xx BeagleBoard X15 revC u-boot from FIT Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11board: ti: am571x: Add 666MHz support for AM571x IDKSteve Kipisz1-2/+33
AM571x supports DDR running at 666MHz. Right now it is clocked at 532MHz which is lower than what is supported. In order to have maximum performance on AM571-IDK, switch DDR to 666MHz. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11board: ti: dra76: Add dt supportLokesh Vutla1-1/+3
Add support for selecting proper dtb for dra76x u-boot from FIT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11board: ti: dra76-evm: Add support for powering on mmc ldoLokesh Vutla1-0/+2
ldo4 is used to poweron mmc on dra76-evm. Enable it. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
generated by cgit v1.1 at 2024-07-12 01:31:42 +0000