aboutsummaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)AuthorFilesLines
2016-02-08OMAP3: omap3_logic: Enable Android FastbootAdam Ford1-0/+37
Android Fastboot requires USB. The TWL4030 PMIC on omap3_logic handles USB traffic. This patch sets up the USB gadget and Android Fastboot to match what is done in the omap3_beagle project. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08OMAP3: Enable SPL on omap3_logicAdam Ford1-0/+56
Previously, Omap3_logic assumed X-loader was present. With this patch, we can finally replace X-loader with an MLO generated by U-Boot. This requires ECC to be setup to match the Linux Kernel and the PBIAS confgured for the SD card. Signed-off-by: Derald D. Woods <woods.technical@gmail.com> Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-08rpi: fix up Model B entriesLubomir Rintel1-10/+10
The P5 header was not present on "Model B" any board prior to Revision 2.0, there's no need for a separate device tree. Also, it looks like "rev2" is incorrectly used to only cover the 512MiB memory models; there also were 256MiB 2.0 boards. I don't have all of the boards to check this, I'm following this table: http://elinux.org/RPi_HardwareHistory#Board_Revision_History Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
2016-02-08rpi: link to another model number info sourceStephen Warren1-0/+5
This source has been blessed by Dom Cobley at the RPi Foundation, so seems like the best source to refer to. It's a superset of and consistent with the other sources. Cc: Lubomir Rintel <lkundrak@v3.sk> Cc: Eric Anholt <eric@anholt.net> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2016-02-08serial: serial_stm32: move clock config from driver to boardVikas Manocha1-0/+3
This patch removes the uart clock enable from serial driver & move it in the board code. Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-02-08ARM: omap3_logic: Fix pin muxingAdam Ford1-65/+313
Enhance pin muxing to enable more board features and reduce power based on Tony's device tree work. Signed-off-by: Adam Ford <aford173@gmail.com>
2016-02-08Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini133-317/+317
2016-02-06Use correct spelling of "U-Boot"Bin Meng133-317/+317
Correct spelling of "U-Boot" shall be used in all written text (documentation, comments in source files etc.). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
2016-02-05x86: Drop asm/arch/gpio.hBin Meng1-3/+2
asm/arch/gpio.h is not needed anymore as we get the GPIO base from PCH driver. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
2016-02-04imx: mx6: implement board_mmc_get_env_devPeng Fan4-0/+20
Implement board_mmc_get_env_dev for the boards. Following is examples: SD1/SD2/SD3: return devno; SD2/SD3: return devno - 1; SD2/SD4: if (devno == 2), return dev - 2; return dev - 1; Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-04imx: mx7dsabresd: move mmc_get_env_devno to soc codePeng Fan1-15/+5
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to match the one in common/env_mmc.c. Introduce a weak function board_mmc_get_env_dev. Different boards can implement this according to sdhc controller which is used by the board. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-02imx: mx6sxsabresd: Add MCIMX28LCD display supportYe Li1-0/+61
The i.MX6SX SABRESD board supports MCIMX28LCD (800x480x24) at LCDIF1 port, enable this display feature by adding relevant BSP codes and configurations. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failureYe Li1-1/+1
The BOOTCFG value used by bmode for SABRESD eMMC boot are actually for SD card. Fixed the value to correct one. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02tqma6_wru4: Fix the reset delay for the the LAN8720 PHYFabio Estevam1-1/+1
According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested by the LAN8720 datasheet. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02mx6slevk: Fix the reset delay for the the LAN8720 PHYFabio Estevam1-1/+1
Since commit 59370f3fcd1350 ("net: phy: delay only if reset handler is registered") Ethernet is no longer functional. This commit does not have an issue in itself, but it revelead a problem with the Ethernet initialization. According to the LAN8720 datasheet tpurstd (time that reset line should stay asserted) is 25ms. So do as suggested in order to have Ethernet working again. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-02-02imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO boardYe Li5-0/+668
Initial version for mx6sx SABREAUTO board support with features: PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02arm: imx6: Enable DDR calibration on NovenaMarek Vasut1-9/+14
Enable the DDR calibration functionality on Novena to deal with the memory SoDIMM on this board. Moreover, tweak the initial DDR DRAM parameters so the calibration works properly. Signed-off-by: Marek Vasut <marex@denx.de>
2016-02-02Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini10-18/+121
2016-02-02board: atmel: sama5d2_xplained: add SPL supportWenyou Yang1-0/+103
The sama5d2 Xplained SPL supports the boot medias: spi flash and SD Card. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-02arm: at91/spl: mpddrc: add struct atmel_mpddrc_configWenyou Yang9-18/+18
Add struct atmel_mpddrc_config to accommodate the mpddrc register configurations, not using the mpddrc register map structure, struct atmel_mpddrc, in order to increase readability and reduce run-time memory use. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
2016-02-01board: Add Microchip PIC32MZ[DA]-Starter-Kit board.Purna Chandra Mandal5-0/+79
This adds support for Microchip PIC32MZ[DA] StarterKit board based on a PIC32MZ[DA] family of microcontroller. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-02-01malta: Use I/O accessors for SuperI/O controllerPaul Burton3-11/+11
Rather than passing the I/O port base address to the Super I/O code, switch it to using outb such that it makes use of the I/O port base address automatically. Drop the extern keyword to satisfy checkpatch whilst here. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-02-01malta: Set I/O port base earlyPaul Burton1-4/+2
Set the I/O port base earlier, from board_early_init_f, in preparation for it being used by the serial driver. Signed-off-by: Paul Burton <paul.burton@imgtec.com>
2016-01-28Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini6-12/+12
2016-01-28Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini1-13/+0
2016-01-28arm: ls1021atwr: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng1-2/+2
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: p1010rdb: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng1-2/+2
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: mpc8548cds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng1-2/+2
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: mpc8572ds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng1-2/+2
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: c29xpcie: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng1-2/+2
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28powerpc: bsc9132qds: Do not wrap pci_eth_init() with CONFIG_TSEC_ENETBin Meng1-2/+2
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28ARM: tegra: rm Jetson TK1 PMIC GPIO programmingStephen Warren1-13/+0
The PMIC is configured such that its GPIOs have the correct configuration at power-up, so no programming is required. In fact, the current programming is actively wrong, since: (a) the AS3722 driver configures the GPIO to be an output before setting its output value, which causes a 0v glitch on the output. (b) the AS3722 driver configures the GPIO to drive a high voltage from its VSUP_GPIO power source rather than its VDD_GPIO_LV power source, so the pin drives 5V not 1.8V as desired. Solve these problems by removing the code which configures the PMIC GPIOs. Note that this patch was tested directly on top of v2016.01; since then, commit 96350f729c42 "dm: tegra: net: Convert tegra boards to driver model for Ethernet" prevents PCIe from being initialized. Alternatively, simply revert that commit to get PCIe Ethernet working again, then apply this patch to test. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-01-27Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini12-146/+377
2016-01-27Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini28-384/+109
2016-01-27armv8/ls1043aqds: add QSPI boot supportQianyu Gong3-1/+5
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27armv8/ls1043aqds: add QSPI support in SD bootGong Qianyu2-0/+9
QSPI and IFC are pin-multiplexed on LS1043A. So we use ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27armv8/ls1043aqds: Select lpuart pins of various muxesShaohui Xie1-0/+13
Set Board Configuration Register to select the lpuart pins of various muxes. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27secure_boot: change error handler for esbc_validateAneesh Bansal2-1/+13
In case of error while executing esbc_validate command, SNVS transition and issue of reset is required only for secure-boot. If boot mode is non-secure, this is not required. Similarly, esbc_halt command which puts the core in Spin Loop is applicable only for Secure Boot. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27secure_boot: enable chain of trust for ARM platformsAneesh Bansal4-0/+26
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043). In board_late_init(), fsl_setenv_chain_of_trust() is called which will perform the following: - If boot mode is non-secure, return (No Change) - If boot mode is secure, set the following environmet variables: bootdelay = 0 (To disable Boot Prompt) bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script) Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27secure_boot: create function to determine boot modeAneesh Bansal1-0/+53
A function is created to detrmine if the boot mode is secure or non-secure for differnt SoC's. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27ppc: xilinx-ppc440-generic: Wire LL_TEMAC driverRicardo Ribalda Delgado2-0/+26
If the xparameters file contains a LL_TEMAC definition compile its driver and the net commands. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ppc: xilinx_ppc440_generic: Remove uncalled functionsRicardo Ribalda Delgado1-5/+0
board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not set. Remove unused function. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ppc: xilinx_ppc405_generic: Remove uncalled functionsRicardo Ribalda Delgado1-5/+0
board_pre_init was not called because CONFIG_BOARD_EARLY_INIT_F was not set. Remove unused function. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ppc: xilinx_ppc440_generic: Remove weak attributesRicardo Ribalda Delgado1-11/+7
Now that the specific boards have been removed there is no need to maintain the weak functions. Fix also CamelCase to make checkpatch happy Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ppc: xilinx_ppc405_generic: Remove weak attributesRicardo Ribalda Delgado1-14/+8
Now that the specific boards have been removed there is no need to maintain the weak functions. Fix also CamelCase to make checkpatch happy Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ppc: xilinx-ppc4xx: Port to DM serialRicardo Ribalda Delgado4-2/+8
xilinx_uartlite has been ported to DM, this patch makes the xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new DM driver. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM: zynq: zynqmp: Line up checkboard messageMichal Simek2-2/+2
Use space instead of tab in checkboard print to aligned it with others boards. Reported-by: David Glessner <david.glessner@rockwellcollins.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
2016-01-27ARM64: zynqmp: Remove unneeded timer_init functionMichal Simek1-5/+0
Empty weak function is used instead. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM64: zynqmp: Fix bootmode SD_MODE1Michal Simek1-1/+4
When only sdhci1 IP is enabled and SD_MODE1 bootmode is selected U-Boot using sdboot1 variable which refers to mmc dev 1. But this device doesn't exist because only one controller is available. This patch fix logic around sdboot mode with using sdbootdev internal variable. Reported-by: Chris Kohn <ckohn@xilinx.com> Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27ARM64: zynqmp: Differentiate EMMC boot modeMichal Simek1-1/+4
Show also EMMC bootmode if selected. There is difference compare to SD bootmode. Use the same bootcommand till better boot command is created. Reported-by: Sai Pavan Boddu <saipava@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit v1.1 at 2024-07-16 03:13:18 +0000