aboutsummaryrefslogtreecommitdiff
path: root/board
AgeCommit message (Collapse)AuthorFilesLines
2017-04-18sunxi: Add maintainer of the NanoPi NEO AirJelle van der Waa1-0/+5
Add myself as maintainer of the NanoPi NEO Air board. Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-16Merge git://git.denx.de/u-boot-rockchipTom Rini6-0/+233
2017-04-16Merge git://git.denx.de/u-boot-dmTom Rini2-167/+27
2017-04-15rockchip: ARM64: split RK3399-Q7 board off the RK3399-EVB boardKlaus Goger6-0/+233
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230 connector) system-on-module from Theobroma Systems, featuring the Rockchip RK3399. It provides the following feature set: * up to 4GB DDR3 * on-module SPI-NOR flash * on-module eMMC (with 8-bit interace) * SD card (on a baseboad) via edge connector * Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY * HDMI/eDP/MIPI displays * 2x MIPI-CSI * USB - 1x USB 3.0 dual-role (direct connection) - 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub) * on-module STM32 Cortex-M0 companion controller, implementing: - low-power RTC functionality (ISL1208 emulation) - fan controller (AMC6821 emulation) - USB<->CAN bridge controller Note that we use a multi-payload FIT image for booting and have Cortex-M0 payload in a separate subimage: we thus rely on the FIT image loader to put it into the SRAM region that ATF expects it in. Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Fixed build warning on puma-rk3399: Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-14board: sama5d3_xplained: Enable early debug UARTWenyou Yang1-1/+12
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-14board: sama5d3_xplained: Clean up codeWenyou Yang1-34/+0
Due to the introduction of the pinctrl and clk driver, and using device tree files, remove the unneeded hardcoded pin configuration and clock enabling code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-14board: sama5d3_xplained: Update to support DM/DTWenyou Yang1-0/+2
Update the configuration files to support the device tree and driver model, so do SPL. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Fix build error with sama5d3_xplained_mmc: Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-14board: sama5d3xek: Enable early debug UARTWenyou Yang1-1/+12
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-04-14board: sama5d3xek: Clean up codeWenyou Yang1-133/+1
Due to the introduction of the pinctrl and clk driver, and using device tree files, remove the unneeded hardcoded pin configuration and clock enabling code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Remove CONFIG_PHY_MICREL as per previous patch: Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-14board: sama5d3xek: Update to support DM/DTWenyou Yang1-0/+2
Update the configuration files to support the device tree and driver model, so do SPL. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Add back CONFIG_PHY_MICREL to prevent a build error: Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-14Merge branch 'master' of git://git.denx.de/u-boot-videoTom Rini6-19/+102
2017-04-14Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini7-2/+2
2017-04-14ARM: socfpga: Rename MCVEVKMarek Vasut7-2/+2
The board is now manufactured by Aries Embedded GmbH , rename it. Signed-off-by: Marek Vasut <marex@denx.de>
2017-04-14board: toradex: colibri_vf: Add DCU support for Colibri VybridStefan Agner3-16/+99
The Vybrid SoC family has the same display controller unit (DCU) like the LS1021A SoC. This patch adds platform data, pinmux defines and clock control to enable the driver for Toradex Colibri Vybrid module. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-04-14Convert CONFIG_FSL_DCU_FB to KconfigSanchayan Maity3-3/+3
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB and convert it to Kconfig. Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Reviewed-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-13Merge git://git.denx.de/u-boot-dmTom Rini7-560/+322
Here with some DM changes as well as the long-standing AT91 DM/DT conversion patches which I have picked up via dm.
2017-04-13board: sama5d4ek: enable early debug UARTWenyou Yang1-1/+12
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13board: sama5d4ek: clean up codeWenyou Yang1-133/+1
Due to the introduction of the pinctrl and clk driver, and using device tree files, remove the unneeded hardcoded pin configuration and clock enabling code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13board: sama5d4ek: update to support DM/DTWenyou Yang1-0/+2
Update the configuration files to support the device tree and driver model, so do SPL. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13board: sama5d4_xplained: enable early debug UARTWenyou Yang1-1/+12
Enable the early debug UART to debug problems when an ICE or other debug mechanism is not available. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13board: sama5d4_xplained: clean up codeWenyou Yang1-133/+1
Due to the introduction of the pinctrl and clk driver, and using device tree files, remove the unneeded hardcoded pin configuration and clock enabling code from the board file. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13board: sama5d4_xplained: update to support DM/DTWenyou Yang1-0/+2
Update the configuration files to support the device tree and driver model, so do SPL. The device clock and pins configuration are handled by the clock and the pinctrl drivers respectively. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
2017-04-13gpio: at91_gpio: remove CPU_HAS_PIO3 macroWenyou Yang7-348/+348
The intention of the removal is the preparation to introduce the new AT91 PIO pinctrl driver. Use the union to make the PIO3 and PIO2's registers be together and make their offset aligned. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini28-207/+1173
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13board_f: Rename initdram() to dram_init()Simon Glass117-137/+137
This allows us to use the same DRAM init function on all archs. Add a dummy function for arc, which does not use DRAM init here. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Dummy function on nios2] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-12arm: freescale: Rename initdram() to fsl_initdram()Simon Glass11-11/+14
This function name shadows a global name but is in fact different. This is very confusing. Rename it to help with the following refactoring. Signed-off-by: Simon Glass <sjg@chromium.org>
2017-04-12imx: i.mx6q: add the initial support for LogicPD i.MX6Q SOMAdam Ford6-0/+361
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The SOM has a built-in microSD socket, DDR and NAND flash. The development kit has an SMSC Ethernet PHY, serial debug port and a variety of peripherals. This have been verified to boot the i.MX6Q version over either SD on the development kit or NAND built into the SOM. Items in the dtsi file are specific to the SOM itself. Items in the dts file are in the baseboard. Future versions of the SOM will come out supporting the same basebord and potentially future base boards will come out supporting the same SOM. Signed-off-by: Adam Ford <aford173@gmail.com>
2017-04-12mx6sabresd: README: Add eMMC boot configurationBreno Lima1-8/+47
Explain how to flash the eMMC and how to boot from it. Signed-off-by: Breno Lima <breno.lima@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-04-12board: advantech: dms-ba16: apply the proper register setting to fix the ↵Yung-Ching LIN1-1/+2
voltage peak issue Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register to avoid the voltage peak issue while we do the IEEE PHY comformance test Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12board: advantech: dms-ba16: fix AR8033 reset timing issueYung-Ching LIN1-1/+2
Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12board: advantech: dms-ba16: add the PMIC configuration supportYung-Ching LIN1-0/+51
Change the PMIC bulk configuration from auto mode to sync mode to avoid the voltage shutdown issue Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-12board: advantech: dms-ba16: Add the configuration options for display ↵Yung-Ching LIN1-0/+3
initialization Add the configuration options for display initialization in case we need to do the display initialization in kernel to support different timing settings Signed-off-by: Ken Lin <yungching0725@gmail.com> Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
2017-04-08Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini2-304/+49
2017-04-08Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini2-0/+60
2017-04-08spl: Kconfig: SPL_MMC_SUPPORT depends on GENERIC_MMCAlexandru Gagniuc1-0/+2
spl_mmc.c calls mmc_initialize(). This symbol is provided in drivers/mmc/mmc.c when CONFIG_GENERIC_MMC is enabled. The sunxi Kconfig case is an oddball because it redefines SPL_MMC_SUPPORT. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> [trini: Update arch/arm/cpu/armv8/zynqmp/Kconfig] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-08config: am335x_evm: detect BeagleBone Blue using BLArobertcnelson@gmail.com1-0/+4
BeagleBone Blue is next grenation of boards from BeagleBoard.org, focusing on robotics with a TI wl1835 wireless module for connectivity. This board can be indentified by the BLAx value after A335BNLT (BBB) in the at24 eeprom: BLAx: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|] http://beagleboard.org/blue https://github.com/beagleboard/beaglebone-blue firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08config: am335x_evm: detect Green Wireless using GW1robertcnelson@gmail.com1-0/+4
SeeedStudio BeagleBone Green Wireless (BBGW) is an expansion of the SeeedStudio Green (BBG) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the GW1x value after A335BNLT (BBB) in the at24 eeprom: GW1x [aa 55 33 ee 41 33 33 35 42 4e 4c 54 47 57 31 41 |.U3.A335BNLTGW1A|] http://beagleboard.org/green-wireless http://wiki.seeed.cc/BeagleBone_Green_Wireless/ firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: Stored in at24 eeprom at address 5-16: hexdump -e '8/1 "%c"' /sys/bus/i2c/devices/0-0050/eeprom | cut -b 5-16 Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08config: am335x_evm: detect Black Wireless using BWArobertcnelson@gmail.com1-0/+7
BeagleBone Black Wireless is clone of the BeagleBone Black (BBB) with the Ethernet replaced by a TI wl1835 wireless module. This board can be indentified by the BWAx value after A335BNLT (BBB) in the at24 eeprom: BWAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 57 41 35 |.U3.A335BNLTBWA5|] http://beagleboard.org/black-wireless https://github.com/beagleboard/beaglebone-black-wireless firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address Signed-off-by: Robert Nelson <robertcnelson@gmail.com> CC: Tom Rini <trini@konsulko.com> CC: Jason Kridner <jkridner@beagleboard.org> CC: Will Newton <willn@resin.io> Reviewed-by: Tom Rini <trini@konsulko.com>
2017-04-08board: STiH410-B2260: enable cachesPatrice Chotard1-0/+8
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-04-08board: ti: am57xx: enable input on mmc clockSekhar Nori1-2/+2
As per the latest pinmux data available for AM572x EVM, rev A3, input should be enabled on MMC clock lines for MMC2/2/3 for stable operation. Further, AM572x TRM, SPRUHZ6, Revised June 2016, in section 18.4.6.1.1 "Pad Configuration Registers" states that input should be enabled for MMC 2/3/4 clock lines. Enable input on MMC1 and MMC3 clock to match the latest pinmux data. Input is already enabled on MMC2 clock for BeagleBoard x15. Further, input is already enabled on all MMCx clocks for other AM57xx boards (AM572x and AM571x IDK). Tested with HS and UHS SD card on AM572x EVM Rev A3. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-07arm: sunxi: Add Sunchip CX-A99 initial supportRask Ingemann Lambertsen1-0/+6
The Sunchip CX-A99 is a board used in some media players. It features: An Allwinner A80 ARM SoC (4 * Cortex-A7 + 4 * Cortex-A15 cores) 2 GiB or 4 GiB DDR3 DRAM AXP808 PMIC 16 GB or 32 GB eMMC SDIO Wifi/Bluetooth/FM module SD card slot 1 USB 3.0 connector 2 USB 2.0 connectors SATA connector UART connector (internally) for serial console Ethernet connector (10/100/1000 Mbit/s) HDMI connector Composite video and analog audio connector S/PDIF connector IR remote control receiver This patch adds a defconfig for the board. The DRAM settings are as found in the vendor sys_config.fex file. It has a preliminary device tree for use until a device tree is accepted upstream, after which it can be replaced by the upstream version. Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk> [squash commits, and edited new meanful commit message] Signed-off-by: Jagan Teki <jagan@openedev.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-07scripts: sunxi: Build an raw SPL imageMaxime Ripard1-0/+54
Introduce a new sunxi-spl-with-ecc.bin image with already the right header, ECC, randomizer and padding for the BROM to be able to read it. It needs to be flashed using a raw access to the NAND so that the controller doesn't change a thing to it, since we already have all the right parameters. Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2017-04-07board: samsung: trats2: remove the board_power_init() functionJaehoon Chung1-57/+0
Remove the board_power_init() function. It will be initialized with device-tree. In future, it will be controlled with regulator API. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-04-07board: samsung: trats2: remove the unused functionsJaehoon Chung1-18/+0
Remove the unused functions. Never call the get_soft_i2c_scl/sda_pin() aynwhere. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-04-07board: samsung: trats2: remove the board_i2c_init() functionJaehoon Chung1-29/+0
Remove the board_i2c_init() function. i2c should be initialized with device-tree file. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2017-04-06Remove various unused interrupt related codeTom Rini6-12/+0
With d53ecad92f06 some unused interrupt related code was removed. However all of these options are currently unused. Rather than migrate some of these options to Kconfig we just remove the code in question. The only related code changes here are that in some cases we use CONFIG_STACKSIZE in non-IRQ related context. In these cases we rename and move the value local to the code in question. Fixes: d53ecad92f06 ("Merge branch 'master' of git://git.denx.de/u-boot-sunxi") Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-06Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini3-8/+38
trini: Disable CONFIG_SPL_USE_ARCH_MEMSET on orangepi_2 Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-05board_f: Drop setup_dram_config() wrapperSimon Glass40-40/+120
By making dram_init_banksize() return an error code we can drop the wrapper. Adjust this and clean up all implementations. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05board_f: Drop return value from initdram()Simon Glass126-273/+576
At present we cannot use this function as an init sequence call without a wrapper, since it returns the RAM size. Adjust it to set the RAM size in global_data instead, and return 0 on success. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05board_f: Drop board_type parameter from initdram()Simon Glass128-135/+136
It looks like only cm5200 and tqm8xx use this feature, so we don't really need it in generic code. Drop it and have the users access gd->board_type directly. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
generated by cgit v1.1 at 2024-08-14 02:07:34 +0000