aboutsummaryrefslogtreecommitdiff
path: root/board/freescale/common/vid.c
AgeCommit message (Collapse)AuthorFilesLines
2019-12-02common: Move enable/disable_interrupts out of common.hSimon Glass1-0/+1
Move these two functions into the irq_funcs.h header file. Also move interrupt_handler_t as this is used by the irq_install_handler() function. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-08-22boards: lx2160a: Add support of I2C driver modelChuanhua Han1-0/+84
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the lx2160a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-11env: Move env_get() to env.hSimon Glass1-0/+1
Move env_get() over to the new header file. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Simon Glass <sjg@chromium.org>
2018-12-06board/freescale/vid: Add vdd table for NXP LX2160A SoCPriyanka Jain1-0/+37
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06board/freescale/vid: Add correction for ltc3882 read error.Priyanka Jain1-1/+4
Voltage regulator LTC3882 device has 0.5% voltage read error. So for NXP SoC devices this generally equates to 2mV Update set_voltage_to_LTC for below: 1.Add coorection of upto 2mV in voltage comparison to take care of voltage read error of voltage regulator 2.Add loop max count kept as 100 to avoid infinte loop. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-08board/freescale,lsch3: Add entry for 0.9vPriyanka Jain1-1/+1
As per updated hardware documentation for lsch3 based chips like LS2088A, 0.9v support has been added in possible supported SoC volatges Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini1-2/+1
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTRTom Rini1-2/+0
We have a large number of places where while we historically referenced gd in the code we no longer do, as well as cases where the code added that line "just in case" during development and never dropped it. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-23board: common: vid: Add support for LTC3882 voltage regulator chipRajesh Bhagat1-0/+77
Restructures common driver to support LTC3882 voltage regulator chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Move IR chip specific code in flagRajesh Bhagat1-1/+18
Moves IR chip (IR36021) specific code in flag to resolve compilation issue where it is not present. For example, LS1088A is having a new LTC3882 voltage chip. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common: vid: Add board specific vdd adjust APIRajesh Bhagat1-0/+13
Adds a board specific API namely board_adjust_vdd which is required to define the board VDD adjust settings. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23board: common:vid: Add LS1088A VID Supported voltage valuesRajesh Bhagat1-0/+38
Adds below voltage values supported by LS1088A Soc: 1.025V(default), 0.9875V, 0.9750V, 0.9V, 1.0V, 1.0125V, 1.0250V. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-16env: Rename getenv/_f() to env_get()Simon Glass1-2/+2
We are now using an env_ prefix for environment functions. Rename these two functions for consistency. Also add function comments in common.h. Quite a few places use getenv() in a condition context, provoking a warning from checkpatch. These are fixed up in this patch also. Suggested-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Simon Glass <sjg@chromium.org>
2017-03-14armv8: fsl-lsch3: Update VID supportPriyanka Jain1-12/+162
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like LS2088A, LS2080A differs from existing logic. -VDD voltage array is different -Registers are different -VDD calculation logic is different Add new function adjust_vdd() for LSCH3 compliant SoCs Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Signed-off-by: Arpit Goel <arpit.goel@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-09-14armv8: ls1046aqds: Add LS1046AQDS board supportShaohui Xie1-4/+4
LS1046AQDS Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29armv8/ls2080ardb: Enable VID supportRai Harninder1-1/+14
This patch enable VID support for ls2080ardb platform. It uses the common VID driver. Signed-off-by: Rai Harninder <harninder.rai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21freescale: vid: Return i2c mux to default channelWenbin Song1-3/+9
IR chip is on one of the channels on multiplexed I2C-bus. Reset to default channel after accessing. Signed-off-by: Wenbin Song <wenbin.song@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25powerpc/board/t4240rdb: Enable VID supportYing Zhang1-1/+1
The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25board/freescale/common: Check IR chip mode for VID supportYing Zhang1-1/+16
IR chip on all the boards are required to be used in Intel mode to support VID. VDD will not be adjusted if IR chip is used in other modes. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
2015-11-30armv8/ls1043aqds: add LS1043AQDS board supportShaohui Xie1-0/+22
LS1043AQDS Specification: ------------------------- Memory subsystem: * 2GByte DDR4 DIMM * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * Two RGMII ports * XFI 10G port * SGMII * QSGMII with 4x 1G ports PCIe: supports Gen 1 and Gen 2 SATA 3.0: one SATA 3.0 port USB 3.0: two micro AB connector and one type A connector UART: supports two UARTs up to 115200 bps for console Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> [York Sun: Add CONFIG_SYS_NS16550=y in defconfig] Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05powerpc/t208xqds: VID supportYing Zhang1-0/+491
The fuse status register provides the values from on-chip voltage ID efuses programmed at the factory. These values define the voltage requirements for the chip. u-boot reads FUSESR and translates the values into the appropriate commands to set the voltage output value of an external voltage regulator. Signed-off-by: Ying Zhang <b40530@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
generated by cgit v1.1 at 2024-07-13 09:39:11 +0000