aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/include/asm/arch-mx6
AgeCommit message (Collapse)AuthorFilesLines
2018-09-14imx: imx6ull: fix pinmux input_val for uart5 rx pinHeiko Schocher1-1/+1
just try to bring up an imx6ull board with console on uart5 and found, that input_val for pin MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX is 7 and not 5 on imx6ull. With this patch rx works now. Signed-off-by: Heiko Schocher <hs@denx.de>
2018-07-23imx: add macro to detect whether USB has been initializedStefan Agner1-0/+7
This macro allows to detect whether the boot ROM initialized USB already (serial downloader). This is helpful to reliably detect if the system has been recovered via USB serial downloader. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini26-55/+26
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-26imx6ul: opos6ul: add SPL_DM supportSébastien Szymanski1-4/+0
Since commit commit 152038ea1886 ("i.MX6UL: icore: Add SPL_OF_CONTROL support") the OPOS6UL board doesn't boot anymore. Adding SPL_DM support makes the board boot again. Fixes: commit 152038ea1886 ("i.MX6UL: icore: Add SPL_OF_CONTROL support") Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2018-03-29imx: fix CAAM base for i.MX6ULAnatolij Gustschin1-0/+4
HW accelerated "hash sha256 ..." command doesn't work on i.MX6UL, we get "CAAM was not setup properly or it is faulty" error message. This is due to wrong CAAM base 0x02100000, on i.MX6UL the CAAM base address is 0x02140000. Fix it. Note: with this patch applied the "hash sha256" commant still has some issues on i.MX6UL ("Invalid KEY Command" or other errors). With data cache off the "hash sha256" command works as expected. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04imx: cleanup bootauxPeng Fan1-4/+5
Move i.MX6/7 bootaux code to imx_bootaux.c. The i.MX6/7 has different src layout, so define M4 reg offset to ease the cleanup. Redefine the M4 related BIT for share common code. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-08imx: initialize and use generic timer on i.MX 6UL/ULLStefan Agner1-0/+1
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM generic timer. This change makes use of the ARM generic timer in U-Boot. This is crucial to make the ARM generic timers usable in Linux since timer_init() initalizes the system counter module, which is necessary to use the generic timers CP15 registers. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-04mx6ull: Handle the CONFIG_MX6ULL cases correctlyFabio Estevam3-12/+15
Since commit 051ba9e082f7 ("Kconfig: mx6ull: Deselect MX6UL from CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so take this into consideration in all the checks for CONFIG_MX6UL. This fixes a boot regression. Reported-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Breno Lima <breno.lima@nxp.com> Tested-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
2017-11-27mx6ull: Fix WDOG3 base addressFabio Estevam1-1/+1
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this into account in the base address definition. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-11-09imx6: Add include guards for include/asm/arch-mx6/sys_proto.h fileLukasz Majewski1-0/+5
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-11-09imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCsLukasz Majewski2-0/+24
This commit provides generic function to set the RGMII/HSIC IO voltage level on iMX6 devices. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2017-10-31wandboard: Add support for the MX6QP variantFabio Estevam1-0/+3
Add support for the latest MX6QP wandboard variant. Based on Richard Hu's work from Technexion's U-Boot tree. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-12mx6: sys_proto: Add prototypes for imx6_pcie_toggle() functionsDiego Dorta1-0/+3
When compiling with W=1 errors are observed: drivers/pci/pcie_imx.c:517:12: warning: no previous prototype for ‘imx6_pcie_toggle_power’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_power(void) drivers/pci/pcie_imx.c:528:12: warning: no previous prototype for ‘imx6_pcie_toggle_reset’ [-Wmissing-prototypes] __weak int imx6_pcie_toggle_reset(void) Remove these warnings by adding the functions prototypes on arch-mx6/sys_proto. Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-10-12mx6: clock: Add a prototype for do_mx6_showclocks()Diego Dorta1-0/+1
When compiling with W=1 the following warning is observed: arch/arm/mach-imx/mx6/clock.c:1268:5: warning: no previous prototype for ‘do_mx6_showclocks’ [-Wmissing-prototypes] int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) Remove this warning by adding the function prototype into arch-mx6/clock.h file. Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
2017-09-18imx: add macro to detect whether USB PHY is activeStefan Agner1-0/+7
This macro allows to detect whether the USB PHY is active. This is helpful to detect if the boot ROM has previously started the USB serial downloader. The idea is taken from the mfgtool support in the NXP U-Boot: http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/?h=imx_v2016.03_4.1.15_2.0.0_ga&id=a352ed3c5184b95c4c9f7468f5fbb5f43de5e412 Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2017-08-16imx6: use SION macro in SDn_CMD mux mode bitfield argumentsAnatolij Gustschin1-4/+4
Select SION by appropriate macro instead of constant. Signed-off-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12imx: reorganize IMX code as other SOCsStefano Babic9-9/+9
Change is consistent with other SOCs and it is in preparation for adding SOMs. SOC's related files are moved from cpu/ to mach-imx/<SOC>. This change is also coherent with the structure in kernel. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@nxp.com> CC: Akshay Bhat <akshaybhat@timesys.com> CC: Ken Lin <Ken.Lin@advantech.com.tw> CC: Marek Vasut <marek.vasut@gmail.com> CC: Heiko Schocher <hs@denx.de> CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com> CC: Christian Gmeiner <christian.gmeiner@gmail.com> CC: Stefan Roese <sr@denx.de> CC: Patrick Bruenn <p.bruenn@beckhoff.com> CC: Troy Kisky <troy.kisky@boundarydevices.com> CC: Nikita Kiryanov <nikita@compulab.co.il> CC: Otavio Salvador <otavio@ossystems.com.br> CC: "Eric Bénard" <eric@eukrea.com> CC: Jagan Teki <jagan@amarulasolutions.com> CC: Ye Li <ye.li@nxp.com> CC: Peng Fan <peng.fan@nxp.com> CC: Adrian Alonso <adrian.alonso@nxp.com> CC: Alison Wang <b18965@freescale.com> CC: Tim Harvey <tharvey@gateworks.com> CC: Martin Donnelly <martin.donnelly@ge.com> CC: Marcin Niestroj <m.niestroj@grinn-global.com> CC: Lukasz Majewski <lukma@denx.de> CC: Adam Ford <aford173@gmail.com> CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr> CC: Boris Brezillon <boris.brezillon@free-electrons.com> CC: Soeren Moch <smoch@web.de> CC: Richard Hu <richard.hu@technexion.com> CC: Wig Cheng <wig.cheng@technexion.com> CC: Vanessa Maegima <vanessa.maegima@nxp.com> CC: Max Krummenacher <max.krummenacher@toradex.com> CC: Stefan Agner <stefan.agner@toradex.com> CC: Markus Niebel <Markus.Niebel@tq-group.com> CC: Breno Lima <breno.lima@nxp.com> CC: Francesco Montefoschi <francesco.montefoschi@udoo.org> CC: Jaehoon Chung <jh80.chung@samsung.com> CC: Scott Wood <oss@buserror.net> CC: Joe Hershberger <joe.hershberger@ni.com> CC: Anatolij Gustschin <agust@denx.de> CC: Simon Glass <sjg@chromium.org> CC: "Andrew F. Davis" <afd@ti.com> CC: "Łukasz Majewski" <l.majewski@samsung.com> CC: Patrice Chotard <patrice.chotard@st.com> CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Hans de Goede <hdegoede@redhat.com> CC: Masahiro Yamada <yamada.masahiro@socionext.com> CC: Stephen Warren <swarren@nvidia.com> CC: Andre Przywara <andre.przywara@arm.com> CC: "Álvaro Fernández Rojas" <noltari@gmail.com> CC: York Sun <york.sun@nxp.com> CC: Xiaoliang Yang <xiaoliang.yang@nxp.com> CC: Chen-Yu Tsai <wens@csie.org> CC: George McCollister <george.mccollister@gmail.com> CC: Sven Ebenfeld <sven.ebenfeld@gmail.com> CC: Filip Brozovic <fbrozovic@gmail.com> CC: Petr Kulhavy <brain@jikos.cz> CC: Eric Nelson <eric@nelint.com> CC: Bai Ping <ping.bai@nxp.com> CC: Anson Huang <Anson.Huang@nxp.com> CC: Sanchayan Maity <maitysanchayan@gmail.com> CC: Lokesh Vutla <lokeshvutla@ti.com> CC: Patrick Delaunay <patrick.delaunay@st.com> CC: Gary Bisson <gary.bisson@boundarydevices.com> CC: Alexander Graf <agraf@suse.de> CC: u-boot@lists.denx.de Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-03-19arm: i.MX6UL: add Armadeus Systems OPOS6UL SoM and OPOS6ULDev carrier boardSébastien Szymanski1-0/+16
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet phy. OPOS6ULDev is carrier board for the OPOS6UL. U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09) Trying to boot from MMC1 U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100) CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz) CPU: Industrial temperature grade (-40C to 105C) at 40C Reset cause: POR Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board DRAM: 256 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Video: 800x480x18 In: serial Out: serial Err: serial Net: FEC [PRIME] Hit any key to stop autoboot: 0 Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-17imx6: Add src_base structure define macroJagan Teki1-0/+2
Instead of initializing 'struct src' to SRC_BASE_ADDR on every function better to have global define macro. Reviewed by: Stefano Babic <sbabic@denx.de> Signed-off-by: Jagan Teki <jagan@openedev.com>
2017-01-27ARM: imx6ul: Move liteSOM source to SoC directoryMarcin Niestroj1-0/+16
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested in [1] during discussion of chiliSOM support patches. [1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html Suggested-by: Tom Rini <trini@konsulko.com> Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-16imx: clock: gate clk before changing pix clk muxPeng Fan1-1/+1
The LCDIF Pixel clock mux is not glitchless, so need to gate before changing mux. Also change enable_lcdif_clock prototype with a new input parameter to indicate disable or enable. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-12-16imx: mx6sl: add lcdif clock supportPeng Fan1-0/+21
Add lcdif clock support for i.MX6SL. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16imx: mx6sll: update register addressPeng Fan1-27/+50
Update register address for i.MX6 SLL Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-12-16imx: mx6sll: add pinmux header filesPeng Fan2-0/+1021
Add i.MX6SLL pinmux header files Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-11-30imx6: clock: Enable External Memory Interface [EIM] clock (eim_slow_clock)Lukasz Majewski1-0/+1
This patch extends the imx6 clock code to enable or disable the EIM slow clock, which in necessary when one wants to use EIM interface t o read/write from external memory (e.g. NOR). Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
2016-11-29ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routinesEric Nelson1-1/+1
The DDR calibration routines are gated by conditionals for the i.MX6DQ SOCs, but with the use of the sysinfo parameter, these are usable on at least i.MX6SDL and i.MX6SL variants with DDR3. Also, since only the Novena board currently uses the dynamic DDR calibration routines, these routines waste space on other boards using SPL. Add a KConfig entry to allow boards to selectively include the DDR calibration routines. Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-29mx6: ddr: add routine to return DDR calibration dataEric Nelson1-0/+2
Add routine mmdc_read_calibration() to return the output of DDR calibration. This can be used for debugging or to aid in construction of static memory configuration. This routine will be used in a subsequent patch set adding a virtual "mx6memcal" board, but could also be useful when gathering statistics during an initial production run. Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-29mx6: ddr: pass mx6_ddr_sysinfo to calibration routinesEric Nelson1-2/+2
The DDR calibration routines have scattered support for bus widths other than 64-bits: -- The mmdc_do_write_level_calibration() routine assumes the presence of PHY1, and -- The mmdc_do_dqs_calibration() routine tries to determine whether one or two DDR PHYs are active by reading MDCTL. Since a caller of these routines must have a valid struct mx6_ddr_sysinfo for use in calling mx6_dram_cfg(), and the bus width is available in the "dsize" field, use this structure to inform the calibration routines which PHYs are active. This allows the use of the DDR calibration routines on CPU variants like i.MX6SL that only have a single MMDC port. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Marek Vasut <marex@denx.de>
2016-11-29imx: mx6: ddr: add register MPZQLP2CTL for LPDDR2Eric Nelson1-0/+2
Add constants for the MPZQLP2CTL DDR register for both banks to allow setting the LPDDR2 timing values in .cfg files using a named constant instead of hex addresses as is currently done in mx6slevk and other board files. Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-16imx: mx6ull: update the REFTOP_VBGADJ settingPeng Fan1-0/+1
According to design team, we need to set REFTOP_VBGADJ in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the actually table is as below: '000" - set REFTOP_VBGADJ[2:0] to 3'b000 '001" - set REFTOP_VBGADJ[2:0] to 3'b001 '010" - set REFTOP_VBGADJ[2:0] to 3'b010 '011" - set REFTOP_VBGADJ[2:0] to 3'b011 '100" - set REFTOP_VBGADJ[2:0] to 3'b100 '101" - set REFTOP_VBGADJ[2:0] to 3'b101 '110" - set REFTOP_VBGADJ[2:0] to 3'b110 '111" - set REFTOP_VBGADJ[2:0] to 3'b111 Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Bai Ping <ping.bai@nxp.com>
2016-10-24imx: mx6: Add plugin supportPeng Fan1-0/+159
Add mx6_plugin.S which calls boot rom setup function, generate the second ivt, and jump back to boot rom. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
2016-10-04imx: iomux: fix snvs usage for i.MX6ULLPeng Fan1-0/+1
SNVS TAMPER pin and BOOT MODE pins are in SNVS IOMUXC module, not in IOMUXC, so correct the related registers' offset. Use IOMUX_CONFIG_LPSR flag for these pins, so we can differentiate them from iomuxc pins. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: "Benoît Thébaudeau" <benoit.thebaudeau.dev@gmail.com>
2016-10-04imx: imx6ull: adjust the ldo 1.2v bandgap voltagePeng Fan1-0/+1
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop MISC0 bit[6:4]) setting to 2b'110. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Bai Ping <ping.bai@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-10-04imx: mx6ull: Update memory map addressPeng Fan1-3/+14
Update memory map address for mx6ull. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-10-04imx: mx6ull: update clock settings and CCM register mapPeng Fan1-7/+52
Update Clock settings and CCM register map for i.MX6ULL. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-10-04imx: mx6ull: add iomux header filePeng Fan2-0/+1067
Add iomux header file for i.MX6ULL. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-09-06mx6: ddr: Allow changing REFSEL and REFR fieldsFabio Estevam1-0/+2
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and REFR fields of the MDREF register as 1 and 7, respectively for DDR3 and 0 and 3 for LPDDR2. Looking at the MDREF initialization done via DCD we see that boards do need to initialize these fields differently: $ git grep 0x021b0020 board/ board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */ board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800 board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800 board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800 board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800 board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800 So introduce a mechanism for users to be able to configure REFSEL and REFR fields as needed. Keep all the mx6 SPL users in their current REF_SEL and REFR values, so no functional changes for the existing users. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Eric Nelson <eric@nelint.com>
2016-08-26ARM: Move SYS_CACHELINE_SIZE over to KconfigTom Rini1-6/+0
This series moves the CONFIG_SYS_CACHELINE_SIZE. First, in nearly all cases we are mirroring the values used by the Linux Kernel here. Also, so long as (and in this case, it is true) we implement flushes in hunks that are no larger than the smallest implementation (and given that we mirror the Linux Kernel, again we are fine) it is OK to align higher. The biggest changes here are that we always use 64 bytes for CPU_V7 even if for example the underlying core is only 32 bytes (this mirrors Linux). Second, we say ARM64 uses 64 bytes not 128 (as found in the Linux Kernel) as we do not need multi-platform support (to this degree) and only the Cavium ThunderX 88xx series has a use for such large alignment. Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Prafulla Wadaskar <prafulla@marvell.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Stefan Roese <sr@denx.de> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Vaibhav Hiremath <hvaibhav@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com> Cc: Steve Rae <steve.rae@raedomain.com> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Nikita Kiryanov <nikita@compulab.co.il> Cc: Stefan Agner <stefan.agner@toradex.com> Acked-by: Heiko Schocher <hs@denx.de> Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Cc: Peter Griffin <peter.griffin@linaro.org> Acked-by: Paul Kocialkowski <contact@paulk.fr> Cc: Anatolij Gustschin <agust@denx.de> Acked-by: "Pali Rohár" <pali.rohar@gmail.com> Cc: Adam Ford <aford173@gmail.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Nishanth Menon <nm@ti.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Robert Baldyga <r.baldyga@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Thomas Weber <weber@corscience.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: David Feng <fenghua@phytium.com.cn> Cc: Alison Wang <b18965@freescale.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Cc: York Sun <york.sun@nxp.com> Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com> Cc: Mingkai Hu <mingkai.hu@nxp.com> Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Cc: Aneesh Bansal <aneesh.bansal@freescale.com> Cc: Saksham Jain <saksham.jain@nxp.com> Cc: Qianyu Gong <qianyu.gong@nxp.com> Cc: Wang Dongsheng <dongsheng.wang@nxp.com> Cc: Alex Porosanu <alexandru.porosanu@freescale.com> Cc: Hongbo Zhang <hongbo.zhang@nxp.com> Cc: tang yuantian <Yuantian.Tang@freescale.com> Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com> Cc: Josh Wu <josh.wu@atmel.com> Cc: Bo Shen <voice.shen@atmel.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Hannes Schmelzer <oe5hpm@oevsv.at> Cc: Thomas Chou <thomas@wytron.com.tw> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sam Protsenko <semen.protsenko@linaro.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Christophe Ricard <christophe-h.ricard@st.com> Cc: Anand Moon <linux.amoon@gmail.com> Cc: Beniamino Galvani <b.galvani@gmail.com> Cc: Carlo Caione <carlo@endlessm.com> Cc: huang lin <hl@rock-chips.com> Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Cc: Xu Ziyuan <xzy.xu@rock-chips.com> Cc: "jk.kernel@gmail.com" <jk.kernel@gmail.com> Cc: "Ariel D'Alessandro" <ariel@vanguardiasur.com.ar> Cc: Kever Yang <kever.yang@rock-chips.com> Cc: Samuel Egli <samuel.egli@siemens.com> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@opensource.altera.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Siarhei Siamashka <siarhei.siamashka@gmail.com> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Andre Przywara <andre.przywara@arm.com> Cc: Bernhard Nortmann <bernhard.nortmann@web.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Ben Whitten <ben.whitten@gmail.com> Cc: Tom Warren <twarren@nvidia.com> Cc: Alexander Graf <agraf@suse.de> Cc: Sekhar Nori <nsekhar@ti.com> Cc: Vitaly Andrianov <vitalya@ti.com> Cc: "Andrew F. Davis" <afd@ti.com> Cc: Murali Karicheri <m-karicheri2@ti.com> Cc: Carlos Hernandez <ceh@ti.com> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Ash Charles <ashcharles@gmail.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Daniel Allred <d-allred@ti.com> Cc: Gong Qianyu <Qianyu.Gong@freescale.com> Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Chin Liang See <clsee@altera.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Paul Kocialkowski <contact@paulk.fr>
2016-05-24Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini1-2/+7
2016-05-18arch/arm: add SEC JR0 offsetAlex Porosanu1-2/+7
Freescale PPC SoCs do not hard-code security engine's Job Ring 0 address, rather a define is used. This patch adds the same functionality to the ARM based SoCs (i.e. LS1/LS2 and i.MX parts) Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-17imx: mx6: mx6sl_pins: add GPIO variant for SD1_DAT5Eric Nelson1-0/+1
This patch adds the IOMUX setting for using SD1_DAT5 as GPIO5:9. Signed-off-by: Eric Nelson <eric@nelint.com> Reviewed-by: Peng Fan <van.freenix@gmail.com>
2016-04-19MX6UL: Add definition for UART6 base addressFabio Estevam1-0/+1
Define the UART6_BASE_ADDR for MX6UL. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-04-19imx: mx6: Fix procedure to switch the parent of LDB_DI_CLKAkshay Bhat1-0/+9
Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree, the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is generated, and the LVDS display will hang when the ipu_di_clk is sourced from ldb_di_clk. To fix the problem, both the new and current parent of the ldb_di_clk should be disabled before the switch. This patch ensures that correct steps are followed when ldb_di_clk parent is switched in the beginning of boot. This patch was ported from the 3.10.17 NXP kernel http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d NXP errata number: ERR009219, EB821 Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2016-03-26arm: mx6: Add UART8 base address for i.MX6ULStefan Roese1-0/+1
Add the base address for the i.MX6UL so that this UART can be used. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Ye Li <ye.li@nxp.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2016-02-21imx: mx6: implement functions to boot auxiliary corePeng Fan1-0/+5
Implement arch_auxiliary_core_up and arch_auxiliary_core_check_up. arch_auxiliary_core_check_up is used to check whether M4 is running or not. arch_auxiliary_core_up is to boot M4 core, the m4 core will use the pc and stack which is set in arch_auxiliary_core_up to set R15 and R13 register and boot. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6sx Add RDC mappings of masters and peripheralsPeng Fan2-0/+159
Add the definitions for the RDC mappings for i.MX6 SoloX. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: imx-common: introduce Resource Domain Controller supportPeng Fan1-0/+12
Introduce Resource Domain Controller support for i.MX. Now i.MX6SX and i.MX7D supports this feature to assign masters and peripherals to different domains. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-21imx: mx6: introduce rdc regsPeng Fan1-0/+24
Introudce rdc regs structure and rdc sema reg structure for i.MX6. For now, to i.MX6, only i.MX6SX supports this. Signed-off-by: Ye.Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-02-02mx6: soc: Add ENET2 mac address supportYe Li1-20/+3
The i.MX6SX and i.MX6UL has two ENET controllers, add support for reading MAC address from fuse for ENET2. Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02arm: imx6: Add DDR3 calibration code for MX6 Q/D/DLMarek Vasut1-0/+5
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code fine-tunes the behavior of the MMDC controller in order to improve the signal integrity and memory stability. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-08-12 11:26:00 +0000