aboutsummaryrefslogtreecommitdiff
path: root/arch/arm/dts/stm32mp157a-avenger96.dts
AgeCommit message (Collapse)AuthorFilesLines
2020-04-07Merge tag 'xilinx-for-v2020.07' of ↵Tom Rini1-11/+69
https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next Xilinx changes for v2020.07 common: - Align ENV_FAT_INTERFACE - Fix MAC address source print log - Improve based autodetection code xilinx: - Enable netconsole Microblaze: - Setup default ENV_OFFSET/ENV_SECT_SIZE Zynq: - Multiple DT updates/fixes - Use DEVICE_TREE environment variable for DTB selection - Switch to single zynq configuration - Enable NOR flash via DM - Minor SPL print removal - Enable i2c mux driver ZynqMP: - Print multiboot register - Enable cache commands in mini mtest - Multiple DT updates/fixes - Fix firmware probing when driver is not enabled - Specify 3rd backup RAM boot mode in SPL - Add SPL support for zcu102 v1.1 and zcu111 revA - Redesign debug uart enabling and psu_init delay - Enable full u-boot run from EL3 - Enable u-boot.itb generation without ATF with U-Boot in EL3 Versal: - Enable distro default - Enable others SPI flashes - Enable systems without DDR Drivers: - Gem: - Flush memory after freeing - Handle mdio bus separately - Watchdog: - Get rid of unused global data pointer - Enable window watchdog timer - Serial: - Change reinitialization logic in zynq serial driver Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-01ARM: dts: stm32: Repair PMIC configuration on AV96Marek Vasut1-4/+16
The core and vdd PMIC buck regulators were misconfigured, which caused instability of the board and malfunction of high-speed interfaces, like the RGMII. Configure the PMIC correctly to repair these problems. Also, model the missing Enpirion EP53A8LQI on the DHCOR SoM as a fixed regulator. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-04-01ARM: dts: stm32: Add missing ethernet PHY reset on AV96Marek Vasut1-0/+1
Add PHY reset GPIO on AV96 ethernet PHY. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-04-01ARM: dts: stm32: Repair ethernet operation on AV96Marek Vasut1-2/+2
The AV96 RGMII uses different pinmux for ETH_RGMII_TXD0, ETH_RGMII_RXD2 and ETH_RGMII_TX_CTL. Use the correct pinmux to make ethernet operational. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-04-01ARM: dts: stm32: Add configuration EEPROM on AV96Marek Vasut1-0/+7
The board has an EEPROM on the same I2C bus as PMIC, at address 0x53. The EEPROM contains the board MAC address. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Change-Id: I340a0675c11e4599968b2e3ef0515fb8da8d7b42
2020-04-01ARM: dts: stm32: Add QSPI NOR on AV96Marek Vasut1-0/+20
The DH Electronics DHCOR SOM has QSPI NOR on the SoM itself, add it into the DT. Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Change-Id: Ia7c454c496f50e3fc4851ec1154f3641c416e98e
2020-04-01ARM: dts: stm32: Repair SDMMC2 operationMarek Vasut1-1/+1
The eMMC uses different pinmux for the top four data lines, use such a pinmux, otherwise it takes a very long time until the test for 8bit operation times out. And this is the correct pinmux per schematic too. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-04-01ARM: dts: stm32: Repair SDMMC1 operation on AV96Marek Vasut1-4/+21
The SD uses different pinmux for the D123DIRline, use such a pinmux, otherwise there is a pinmux collision on the AV96. Add missing SD voltage regulator switch and enable SDR104 operation. Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com>
2020-03-24ARM: dts: stm32mp1: DT alignment with Linux 5.6-rc1Patrick Delaunay1-2/+3
This commit manages diversity for STM32M15x SOCs with: - dedicated files to support all STM32MP15 SOCs family. The differences between those SOCs are: -STM32MP151 [1]: common file. -STM32MP153 [2]: STM32MP151 + CANs + a second CortexA7-CPU. -STM32MP157 [3]: STM32MP153 + DSI + GPU. - new files to manage security diversity on STM32MP15x SOCs. On STM32MP15xY, "Y" gives information: -Y = A means no cryp IP and no secure boot. -Y = C means cryp IP + secure boot. - stm32mp157 pinctrl files to better manage package diversity. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13ARM: dts: stm32mp1: DT alignment with kernel v5.5-rc7Patrick Delaunay1-2/+1
Device tree and binding alignment with kernel v5.5-rc7 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2020-02-13stm32mp1: pwr: use the last binding for pwrPatrick Delaunay1-5/+3
Update the driver to use the latest binding from kernel v5.5-rc1: no more use syscon or regmap to access to pwr register and only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg" is available. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
2019-08-27stm32mp1: board: Update the way vdd-supply is retrieved from DTPatrick Delaunay1-1/+4
Due to kernel DT alignment, pwr-supply is renamed to vdd-supply and is a subnode of pwr-regulators. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-08-27ARM: dts: stm32mp1: sync device tree with v5.3-rc2Patrick Delaunay1-16/+23
Synchronize device tree with v5.3-rc2 label and update the associated u-boot dtsi. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-06-06board: stm32mp1: Add Avenger96 board supportManivannan Sadhasivam1-0/+362
Add support for Avenger96 board from Arrow Electronics based on STM32MP157 MPU. This board is one of the Consumer Edition (CE) boards of the 96Boards family and has the following features: SoC: STM32MP157AAC PMIC: STPMIC1A RAM: 1024 Mbyte @ 533MHz Storage: eMMC v4.51: 8 Gbyte microSD Socket: UHS-1 v3.01 Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac Bluetooth®v4.2 (BR/EDR/BLE) USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4 LED: 4x User LED, 1x WiFi LED, 1x BT LED More information about this board can be found in 96Boards website: https://www.96boards.org/product/avenger96/ Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
generated by cgit v1.1 at 2024-09-16 03:43:33 +0000