aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2015-10-23nios2: BSS should be cleared only after board_init_fThomas Chou1-14/+16
As dtb in u-boot-dtb.bin overlapped the BSS section, we should delay the clearing of BSS until dtb is relocated in board_init_f(). Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Acked-by: Marek Vasut <marex@denx.de>
2015-10-23nios2: move altera_pio_init to board_early_init_rThomas Chou2-4/+10
As altera_pio_init() uses BSS, it should be moved to board_early_init_r(). Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Acked-by: Marek Vasut <marex@denx.de>
2015-10-23nios2: permit device tree control of U-BootThomas Chou1-0/+1
Enable this in the Kconfig so that nios2 boards can use device tree to configure U-Boot. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Marek Vasut <marex@denx.de>
2015-10-23nios2: enable CONFIG_NET_RANDOM_ETHADDRThomas Chou1-0/+1
Enable CONFIG_NET_RANDOM_ETHADDR to generate a random MAC address when ETHADDR is not set. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Cc: Joe Hershberger <joe.hershberger@ni.com>
2015-10-23nios2: move command line configuration to KconfigThomas Chou2-8/+4
This patch moves command line configuration from board header file to board defconfig in the way of Kconfig. The change passed savedefconfig. This fixes warnings such as : "CONFIG_SYS_HUSH_PARSER" redefined, when "Use hush shell" is selected with menuconfig, etc. Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
2015-10-22ARM: AM335x: mux: change mmc0 cd pinmux from mmc0_sdcd to gpioMugunthan V N1-1/+1
Currently omap_hsmmc driver doesn't use sdcd pin to detect whether the card is present or not. Instead the same pin is used as GPIO to detect card presence. So change the pin mux mode from mmc0_sdcd to gpio0_6. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22drivers: gpio: omap: add support for parsing additional gpio parametersMugunthan V N1-0/+11
With DM_GPIO, gpio parameters like ACTIVE_(LOW/HIGH) are to be parsed in xlate gpio drivers-ops. Since xlate is not implemented in omap_gpio driver, the driver considers all gpio to be ACTIVE_HIGH which is the default case and fails to return actual gpio status for ACTIVE_LOW gpios. So adding .xlate ops to omap_gpio. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-10-22am437x: Add am57xx_evm_defconfig using CONFIG_DMMugunthan V N3-0/+719
Import various DT files for am57xx-beagle-x15 from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22ti_omap5_common: mmc: do not define DM_MMC for splMugunthan V N1-0/+8
Since spl doesn't support DM currently, do not define DM_MMC for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> asdfsadf
2015-10-22am437x: Add am437x_sk_evm_defconfig using CONFIG_DMMugunthan V N3-1/+722
Import various DT files for am437x-sk-evm from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22am437x: Add am437x_gp_evm_defconfig using CONFIG_DMMugunthan V N7-0/+2618
Import various DT files for am4372, an43xx pinctrl and am437x-gp-evm from Linux Kernel v4.2 Add config file for this board, enable DM, DM_GPIO, DM_SERIAL and DM_MMC. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22am43xx_evm: mmc: do not define DM_MMC for splMugunthan V N1-0/+8
Since spl doesn't support DM currently, do not define DM_MMC for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22am43xx_evm.h: : switch to CONFIG_OMAP_SERIAL for non-SPL DM_SERIALMugunthan V N1-1/+5
Tested on am437x gp evm and am437x sk evm Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22drivers: serial: serial_omap: add comaptibles for all ti platformsMugunthan V N1-0/+4
Adding compatibles for am335x, am437x and dra7 platforms. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22drivers: serial: serial_omap: populate default clock frequency when not ↵Mugunthan V N1-1/+3
found in dt In some platforms like am437x, serial node is not populated with clock-frequency node. So in that case have a default clock-clock frequency. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22defconfig: am335x: gp_evm: enable mmc driver modelMugunthan V N1-0/+1
enable mmc driver model for am335x gp_evm as omap_hsmmc supports driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22defconfig: am335x: bbb: enable mmc driver modelMugunthan V N1-0/+1
enable mmc driver model for am335x bbb as omap_hsmmc supports driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22drivers: mmc: omap_hsmmc: convert driver to adopt device driver modelMugunthan V N1-1/+116
adopt omap_hsmmc driver to device driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22am335x_evm: mmc: do not define DM_MMC for splMugunthan V N1-0/+8
Since spl doesn't support DM currently, do not define DM_MMC for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22omap_hsmmc: update struct hsmmc to accomodate base address from DTMugunthan V N1-0/+3
Existing driver gets the actual omap hammc base address + 0x100 bytes as the first 0x100 bytes is not used by the driver. But with DM conversion the base address from DT is different, to accommodate the offset adding res0[0x100] to struct hsmmc. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22dra7xx: Add dra74_evm_defconfig using CONFIG_DMMugunthan V N4-1/+801
Import various DT files for dra7-evm from Linux Kernel v4.2 Add config file for this board, enable DM and DM_GPIO Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22ARM: k2g: Add config fileLokesh Vutla3-0/+75
Add config file for k2g Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
2015-10-22ARM: dts: k2g: Add DT supportLokesh Vutla3-1/+95
Add basic DT support for k2g evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Enable SPI flashLokesh Vutla1-0/+6
GPIO1_9 controls SPI flash on k2g evm. So make GPIO1_9 as output pin, inorder to use SPI. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: add SD card and eMMC supportRoger Quadros3-2/+43
Add MMC support for k2g Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22ARM: k2g: Add Ethernet SupportVitaly Andrianov2-0/+24
Add Ethernet support for tftp support Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22driver: net: keystone_net: removing unused codeMugunthan V N1-10/+0
remove unused code as the same is achieved when configuring sgmii and link status is verifed. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22driver: net: keystone_net: add support for rgmii phyVitaly Andrianov2-1/+48
In K2G, Ethernet doesn't support SGMII instead it support RGMII, adding support to the driver to connect to RGMII phy. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22dma: keystone_nav: Fix linkram sizeVitaly Andrianov1-1/+1
Fix Linkram size. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22driver: net: keystone_net: fix phy mode configurationMugunthan V N5-2/+20
Phy mode is a board property and it can be different between multiple board and ports, so it should not be hardcoded in driver to one specific mode. So adding a field in eth_priv_t structure to pass phy mode to driver. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: update keystone nav rx queue numbersVitaly Andrianov1-0/+5
update K2G nav rx queue number Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Correct base addressesVitaly Andrianov3-0/+57
Coreect base addresses for SPI, Queue Manager, Ethernet, GPIO, and MSMC segments. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add pin mux dataVitaly Andrianov2-0/+316
Add pin mux data for k2g-evm Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add support for pin mux configurationVitaly Andrianov1-0/+58
Add api for configuring pin mux. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add ddr3 infoVitaly Andrianov6-5/+85
Add ddr3 related info Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add PSC infoVitaly Andrianov2-0/+55
Add psc information for k2g Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add clock informationVitaly Andrianov7-3/+34
Add clock information for Galileo Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-10-22ARM: k2g: Add pll dataVitaly Andrianov6-0/+95
Add pll data for k2g Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add kconfig supportLokesh Vutla2-0/+16
Add Kconfig support Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: k2g: Add support for CPU detectionLokesh Vutla2-0/+9
Adding CPU detection support for Keystone2 Galileo. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: keystone2: Use dtb images by defaultLokesh Vutla2-9/+9
Now that OF_CONTROL is enabled on all keystone2 platforms, build the default images with DT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: k2e: Enable OF_CONTROL and DMLokesh Vutla6-1/+590
Import k2e specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: k2l: Enable OF_CONTROL and DMLokesh Vutla6-1/+700
Import k2l specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: k2hk: Enable OF_CONTROL and DMLokesh Vutla8-1/+944
Import k2hk specific DT files from Linux Kernel and enable OF_CONTROL, DM, DM_SERIAL. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: keystone2: Do not use LPAE addresses in U-BootLokesh Vutla1-9/+8
Keystone dts files assumes that LPAE is enabled and top level root node uses 64bit addresses. This breaks the keystone boot with CONFIG_OF_CONTROL enabled. So do not use 64 bit addresse in U-Boot DT. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: dts: Keystone2: Import generic dt files from Linux KernelLokesh Vutla2-0/+738
Import various generic dts files from Linux kernel so that all keystone2 platforms can be DT in U-boot. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: keystone2: spl: Fix stack allocation with CONFIG_SYS_MALLOC_F_LENLokesh Vutla1-0/+7
If CONFIG_SYS_MALLOC_F_LEN is enabled, the stack is moved down to the specified size to make the malloc function available before relocation. But on keystone platforms SYS_SPL_MALLOC is immediately preceding stack, which is causing an overlap with this config enabled. So leave a gap between malloc space and stack space. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ARM: keystone2: Fix serial port initLokesh Vutla1-0/+2
With CONFIG_DM_SERIAL is enabled NS16550_init() cannot be called directly. Driver probe should be taking care of this. So call this function only when DM_SERIAL is not enabled. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22dra72_evm: Switch to DM_SERIALTom Rini1-1/+3
Tested on J6Eco EVM. Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
2015-10-22ti_omap5_common.h: Switch to CONFIG_OMAP_SERIAL for non-SPL DM_SERIALTom Rini1-0/+4
Tested on J6Eco EVM Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.1 at 2024-09-07 22:14:53 +0000