aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2020-07-27board: fsl: lx2160aqds: identify SDHC adapter during board initYangbo Lu2-3/+44
Add support for SDHC adapter identification and configuration during board init. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27Move eSDHC adapter card identification to board filesYangbo Lu11-79/+33
The eSDHC adapter card identification and multiplexing configuration through FPGA had been implemented in both common mmc driver and fsl_esdhc driver. However it is proper to move these code to board files and do it during board initialization. The FPGA registers are also board specific. This patch is to move eSDHC adapter card identification and multiplexing configuration from mmc driver to specific board files. And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [Rebased, Removed T1040QDS change as board does not exist] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27Drop global data sdhc_adapter for powerpcYangbo Lu2-4/+1
The sdhc_adapter of global data has not been used, and we do not have to use it as global data even we may need it in the future. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: ls1028ardb: add xspi parameter to qixis commandYuantian Tang2-2/+15
Add xspi boot source to qixis command to let the soc boot from flex-nor flash chip. Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: ls1012a: RGMII ports require internal delayChaitanya Sakinam2-2/+2
The correct setting for the RGMII ports on LS1012ARDB is to enable delay on both Rx and Tx so the interface mode used should be PHY_INTERFACE_MODE_RGMII_ID Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Signed-off-by: Anji J <anji.jagarlmudi@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27include/configs: ls1012a: Remove fdt_high env variableUdit Agarwal5-5/+5
Remove "fdt_high" environment variable to use the bootm_size to safely contain a kernel, device tree and initrd for relocation. Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27config: lx2160/2a: enable dspiZhao Qiang1-0/+3
Enable dspi in lx2160aqds tfa defconfig Enable CONFIG_SPI_FLASH_SST/EON in config file. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: dts: fsl-lx2160a: add flash node under dspi to qds dtsZhao Qiang1-0/+99
Add flash node under dspi into fsl-lx2160a-qds.dtsi Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27crypto/fsl: fix unaligned accessMichael Walle1-14/+13
On aarch64 running with dcache off, will result in an unaligned access exception: => dcache off => hash sha1 $kernel_addr_r 100 "Synchronous Abort" handler, esr 0x96000061 elr: 00000000960317d8 lr : 00000000960316a4 (reloc) elr: 00000000fbd787d8 lr : 00000000fbd786a4 [..] The compiler emits a "stur x1, [x0, #12]". x1 is might just be 32 bit aligned pointer. Remove the unused u64 element from the union to drop the minimal alignment to 32 bit. Also remove the union, because it is no more needed. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27I2C: ls1043a, ls1046a: enable SYS_I2C_MXCBiwen Li3-5/+3
This enables SYS_I2C_MXC to fix a bug that failed to boot from sd card with image u-boot-with-spl-pbl.bin Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: rework spin tableMichael Walle1-60/+23
There are two issues: (1) The spin table doesn't convert the endianness of the jump address. Although there is code for it, the result isn't used at all (x0). (2) If something goes wrong, the function returns. But that doesn't make sense at all. Use the actual converted jump address as destination to fix. If there is an error, jump to a trap loop. And rearrange the code exception level switching code to make it smaller and clearer. This reduces the size of the spin table code section from 696 bytes to 424 bytes. If CONFIG_ARMV8_SWITCH_TO_EL1 the code size reduced from 696 bytes to 632 bytes. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: relocate spin table if EFI_LOADER is enabledMichael Walle1-0/+36
On ARM64, a 64kb region is reserved for the runtime services code. Unfortunately, this code overlaps with the spin table code, which also needs to be reserved. Thus now that the code is relocatable, allocate a new page from EFI, copy the spin table code into it, update any pointers to the old region and the start the secondary CPUs. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: clean exported symbols in spintable.SMichael Walle4-21/+24
Add a new variable secondary_boot_code_start, which holds a pointer to the start of the spin table code. This will help to relocate the code section. While at it, move the size variable from the end to the beginning so there is a common section for the variables. Remove any other symbols. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: drop first .ltorg directive in spintable.SMichael Walle1-2/+0
Now that the spin table is in a separate module, this is no longer necessary. Drop it. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: make wake_secondary_core_n() staticMichael Walle1-1/+1
This function is not used outside the module. Make it static. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: simplify get_spin_tbl_addr() callsMichael Walle1-8/+7
There is no need to cast around. Assign the address to the local variable and use it. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: remove determine_mp_bootpg()Michael Walle2-6/+0
Only the PowerPC architecture needs this function. Remove it. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: fix alignment for spin tableMichael Walle1-2/+2
Fix the alignment so it will match the comments. The spin table has to be 8 byte aligned, so ".align 3" is enough. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: load function pointer using ADRMichael Walle1-3/+3
Don't use LDR to load a pointer to a function. This will generate a literal which cannot be relocated. Use ADR which is PC-relative and therefore can easily be relocated. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: move spin table into own moduleMichael Walle3-150/+161
Move it out of lowlevel.S into spintable.S. On layerscape, the secondary CPUs are brought up in main u-boot. This will make it possible to only compile the spin table code for the main u-boot and omit it in SPL. This saves about 720 bytes in the SPL. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: properly use CPU_RELEASE_ADDRMichael Walle8-9/+18
The generic armv8 code already has support to bring up the secondary cores. Thus, don't hardcode the jump in the layerscape lowlevel_init to the spin table code; instead just return early and let the common armv8 code handle the jump. This way we can actually use the CPU_RELEASE_ADDR feature. Signed-off-by: Michael Walle <michael@walle.cc> [Rebased, Removed kontron_sl28.h change as file does not exist] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: pretty print info about SMP coresMichael Walle1-4/+5
Make the print of the starting address a debug output and pretty print the info about online cores. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: layerscape: fix spin-table supportMichael Walle2-11/+5
Spin tables are broken with bootefi. This is because - in contrast to the booti call chain - there is no call to smp_kick_all_cpus(). Due to this missing call the secondary CPUs are never released from their "wait for interrupt state", see secondary_boot_func() in lowlevel.S. Originally, this "wait for interrupt" is there to make sure, the spin table is cleared before the secondary cores read it for the first time. But the boot flow for the layerscape architecture is different from that. The CPUs are release from their BootROM _after_ U-Boot's spin-table is cleared, see fsl_layerscape_wake_seconday_cores() in mp.c. Thus, there is no need to wait for this interrupt and no need for kicking all cores on cpu_release. An atomic 64bit write to the spin-table and a "sev" is sufficient. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27net: pfe_eth: Use spi_flash_read API to access flash memoryKuldeep Singh2-2/+48
Current PFE firmware access spi-nor memory directly. New spi-mem framework does not support direct memory access. So, let's use spi_flash_read API to access memory instead of directly using it. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27dm: armv8: gpio: include <asm/arch/gpio.h> for fsl-layerscapehui.song1-6/+2
Enable the gpio feature on fsl-layerscape platform. Signed-off-by: hui.song <hui.song_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: gpio: add gpio featurehui.song1-0/+22
add one struct mpc8xxx_gpio_plat to enable gpio feature. Signed-off-by: hui.song <hui.song_1@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27configs: ls1088ardb: Add support for usb boot targetEra Tiwari1-0/+1
LS1088A-RDB has MMC, SCSI, DHCP as boot targets, but the USB support was missing. Add support for USB as Boot_targets_devices. Signed-off-by: Era Tiwari <era.tiwari@nxp.com> Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27armv8: ls1028a: move FSL_LAYERSCAPE to kconfigMichael Walle2-1/+1
CONFIG_FSL_LAYERSCAPE is available in kconfig. There is no need to define it per board; the ls1028a_common.h is really board dependent and only fits to the NXP eval boards. Instead select CONFIG_FSL_LAYERSCAPE when ARCH_LS1028A is selected. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-27fsl_dspi: Introduce DT bindings for CS-SCK and SCK-CS delaysVladimir Oltean3-1/+58
Communication with some SPI slaves just won't cut it if these delays (before the beginning, and after the end of a transfer) are not added to the Chip Select signal. These are a straight copy from Linux: Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt drivers/spi/spi-fsl-dspi.c Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-07-26binman: Re-enable concurrent testsSimon Glass1-1/+3
With the change to absolute imports the concurrent tests feature unfortunately broke. Fix it. We cannot easy add a warning, since the output messes up tests which check the output. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-26binman: Don't change the descriptor in testsSimon Glass3-5/+47
At present testPackX86RomMeNoDesc removes the contents of the descriptor.bin file and testPackX86RomMeMissingDesc removes the file completely. If a test that relies on this file happens to run after it is removed, it will not work. Since we have no control over the selecting of tests that run in parallel and series, we must avoid changing the files. Update this tests to use separate files instead. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-26env: mmc: add redundancy support in mmc_offset_try_partitionPatrick Delaunay1-3/+3
Manage 2 copy at the end of the partition selected by config "u-boot,mmc-env-partition" to save the U-Boot environment, with CONFIG_ENV_SIZE and 2*CONFIG_ENV_SIZE offset. This patch allows to support redundancy (CONFIG_ENV_OFFSET_REDUND). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-26env: mmc: correct the offset returned by mmc_offset_try_partitionPatrick Delaunay1-2/+2
The output of the function mmc_offset_try_partition must be a byte offset in mmc and not a multiple of blksz. This function is used in mmc_offset(), called by mmc_get_env_addr() and the offset is used in write_env(), erase_env() and read_env(). In these function, blk_start = offset / mmc->read_bl_len or /write_bl_len so this offset is not a multiple of blksz. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-26env: mmc: allow support of mmc_get_env_dev with OF_CONTROLPatrick Delaunay1-6/+12
Use the weak function mmc_get_env_dev in mmc_offset_try_partition function to allow dynamic selection of mmc device to use and no more use directly the define CONFIG_SYS_MMC_ENV_DEV. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-26test: env: add test for env info sub-commandPatrick Delaunay1-0/+63
Add a pytest for testing the env info sub-command: test_env_info: test command with several option that can be executed on real hardware device without assumption test_env_info_sandbox: test the result on sandbox with a known ENV configuration: ready & default & persistent The quiet option '-q' is used for support in shell test; for example: if env info -p -d -q; then env save; fi Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Stephen Warren <swarren@nvidia.com>
2020-07-26configs: sandbox: Enable sub command 'env info'Patrick Delaunay4-0/+4
Enable support for sub command 'env info' in sandbox with CONFIG_CMD_NVEDIT_INFO. This is aimed primarily at adding unit test. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-26cmd: env: check real location for env info commandPatrick Delaunay2-3/+23
Check the current ENV location, dynamically provided by the weak function env_get_location to be sure that the environment can be persistent. The compilation flag ENV_IS_IN_DEVICE is not enough when the board dynamically select the available storage location (according boot device for example). This patch solves issue for stm32mp1 platform, when the boot device is USB. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2020-07-26cmd: env: add option for quiet output on env infoPatrick Delaunay2-7/+20
The "env info" can be use for test with -d and -p parameter, in scripting case the output of the command is not needed. This patch allows to deactivate this output with a new option "-q". For example, we can save the environment if default environment is used and persistent storage is managed with: if env info -p -d -q; then env save; fi Without the quiet option, I have the unnecessary traces First boot: Default environment is used Environment can be persisted Saving Environment to EXT4... File System is consistent Next boot: Environment was loaded from persistent storage Environment can be persisted Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com>
2020-07-26env: add failing trace in env_savePatrick Delaunay1-3/+7
Add trace in env save to indicate any errors to end user and avoid silent output when the command 'env save' is not executed. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-26env: correct overflow check of env_has_init sizePatrick Delaunay1-1/+1
Correct the overflow check of the bit-field env_has_init with the max value of env_location= ENVL_COUNT and no more with the size of env_locations. This bit-field is indexed by this enumerate and not by the position in the env_locations (only used in env_get_location) and the 2 values are different, depending of thea ctivated CONFIG_ENV_IS_ options. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-07-26env/fat.c: allow loading from a FAT partition on the MMC boot deviceDavid Woodhouse2-2/+34
I don't want to have to specify the device; only the partition. This allows me to use the same image on internal eMMC or SD card for Banana Pi R2, and it finds its own environment either way. Signed-off-by: David Woodhouse <dwmw2@infradead.org> [trini: Add #if/#else/#endif logic around CONFIG_SYS_MMC_ENV_DEV usage, whitespace changes] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-25treewide: convert devfdt_get_addr() to dev_read_addr()Masahiro Yamada120-125/+125
When you enable CONFIG_OF_LIVE, you will end up with a lot of conversions. To generate this commit, I used coccinelle excluding drivers/core/, include/dm/, and test/ The semantic patch that makes this change is as follows: <smpl> @@ expression dev; @@ -devfdt_get_addr(dev) +dev_read_addr(dev) </smpl> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-07-25treewide: remove (phys_addr_t) casts from devfdt_get_addr()Masahiro Yamada5-5/+5
This cast is unneeded. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-07-25treewide: convert (void *)devfdt_get_addr() to dev_read_addr_ptr()Masahiro Yamada46-47/+47
Use the _ptr suffixed variant instead of casting. Also, convert it to dev_read_addr_ptr(), which is safe to CONFIG_OF_LIVE. One curious part is an error check like follows in drivers/watchdog/omap_wdt.c: priv->regs = (struct wd_timer *)devfdt_get_addr(dev); if (!priv->regs) return -EINVAL; devfdt_get_addr() returns FDT_ADDR_T_NONE (i.e. -1) on error. So, this code does not catch any error in DT parsing. dev_read_addr_ptr() returns NULL on error, so this error check will work. I generated this commit by the following command: $ find . -name .git -prune -o -name '*.[ch]' -type f -print | \ xargs sed -i -e 's/([^*)]*\*)devfdt_get_addr(/dev_read_addr_ptr(/' I manually fixed drivers/usb/host/ehci-mx6.c Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2020-07-25fdt_support: skip MTD node with "disabled" in fdt_fixup_mtdparts()Masahiro Yamada1-7/+10
Currently, fdt_fixup_mtdparts() only checks the compatible property. It is pointless to fix up the disabled node. Skip the node if it has the property: status = "disabled" Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-25fdt_support: call mtdparts_init() after finding MTD node to fix upMasahiro Yamada1-3/+8
Platform code can call fdt_fixup_mtdparts() in order to hand U-Boot's MTD partitions over to the Linux device tree. Currently, fdt_fixup_mtdparts() calls mtdparts_init() in its entry. If no target MTD device is found, an error message like follows is displayed: Device nand0 not found! This occurs when the same code (e.g. arch/arm/mach-uniphier/fdt-fixup.c) is shared among several boards, but not all of them support an MTD device. Parse the DT first, then call mtdparts_init() only when the target MTD node is found. Yet, you still need to call mtdparts_init() before device_find(). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-07-25test/dm: check if devices existHeinrich Schuchardt5-5/+18
Running 'ut dm' on the sandbox without -D or -d results in segmentation faults due to NULL pointer dereferences. Check that device pointers are non-NULL before using them. Use ut_assertnonnull() for pointers instead of ut_assert(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Philippe Reynes <philippe.reynes@softathome.com>
2020-07-25arm: mach-k3: Use SOC driver for device identificationDave Gerlach3-36/+19
Make use of UCLASS_SOC to find device family and revision for print_cpuinfo. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-25configs: j721e_evm: Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3Dave Gerlach4-0/+8
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC driver can be used for SoC detection. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
2020-07-25configs: am65x_evm: Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3Dave Gerlach4-0/+8
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC driver can be used for SoC detection. Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
generated by cgit v1.1 at 2024-07-31 04:04:57 +0000