aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2021-10-19apalis-imx6: use dynamic DDR calibrationFrancesco Dolcini2-0/+20
Enable dynamic DDR calibration to have a reliable behavior on edge temperatures conditions. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-10-19colibri-imx6: use dynamic DDR calibrationFrancesco Dolcini2-0/+23
Enable dynamic DDR calibration to have a reliable behavior on edge temperatures conditions. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-10-07mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULPOleksandr Suvorov2-3/+8
Import HS400 support for iMX7ULP B0 from the Linux kernel: 2eaf5a533afd ("mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP") According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET before any setting of STROBE_DLL_CTRL register. USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL) for slave sel value. If this register bits value is 0, it needs 256 ref_clk cycles to update slave sel value. IC suggest to set bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave sel value. This will short the lock time of slave. i.MX7ULP B0 will need more time to lock the REF and SLV, so change to add 5us delay. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
2021-10-07mmc: fsl_esdhc_imx: initialize data for imx7ulpJorge Ramirez-Ortiz1-1/+6
Import data for eSDHC driver for SoC iMX7ULP from the Linux kernel. Set supported by u-boot flags only. Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
2021-10-07arm64: dts: imx8mm-venice-gw7902: use imx8mm-venice-u-boot.dtsiTim Harvey1-53/+1
Use the common imx8mm-venice-u-boot.dtsi (dtb for the 'DEFAULT_DEVICE_TREE) so that it inherits things like binman. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07arm64: dts: imx8mm-venice-gw7901: use imx8mm-venice-u-boot.dtsiTim Harvey1-61/+5
Use the common imx8mm-venice-u-boot.dtsi (dtb for the 'DEFAULT_DEVICE_TREE) so that it inherits things like binman. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07arm64: dts: imx8mm-venice-gw700x: use imx8mm-venice-u-boot.dtsiTim Harvey1-53/+9
Use the common imx8mm-venice-u-boot.dtsi (dtb for the 'DEFAULT_DEVICE_TREE) so that it inherits things like binman. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07smegw01: Pass 'mmcpart' to the kernel command lineFabio Estevam1-2/+1
When using SWUpdate, it is necessary to toggle between partitions. Use the 'mmcpart' environment variable to accomplish that. Signed-off-by: Fabio Estevam <festevam@denx.de>
2021-10-07imx: makefile: drop the use of imx8mimage.shPeng Fan1-6/+7
After switch to use binman, no need to use the bash script to check file exsiting or not. And there is bug that the script will be executed everytime Makefile is used which is confusing people. Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2021-10-07tools: imx8mimage: not abort when mmap failPeng Fan1-1/+2
When creating flash.bin, the hdmi firmware might not be copied to U-Boot source tree. Then mkimage will fail. However we are switching to binman, binman will show the message if the file not there, and create empty file per i.MX8MQ binman node. So we not fail mkimage here othersize CI will fail if hdmi firmware not copied here. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-10-07imx: imx8mm: Add support for Kontron Electronics SL/BL i.MX8M-Mini boards ↵Frieder Schrempf17-0/+3705
(N801x) The Kontron SoM-Line i.MX8MM (N801x) by Kontron Electronics GmbH is a SoM module with an i.MX8M-Mini SoC, 1/2/4 GB LPDDR4 RAM, SPI NOR, eMMC and PMIC. The matching evaluation boards (Board-Line) have 2 Ethernets, USB 2.0, HDMI/LVDS, SD card, CAN, RS485 and much more. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
2021-10-07imx53: usbarmory: Use ethernet driver modelAndrej Rosano1-0/+1
Enable ethernet driver model as it is mandatory. Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
2021-10-07imx: ventana: fix USB hub resetTim Harvey7-41/+62
Remove board_ehci_hcd_init function that is not used with DM_USB and replace its functionality with device-tree configuraton that treats USB HUB RST# as a gpio enable for the usbh1 vbus regulator. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: ventana: update LVDS supportTim Harvey1-17/+42
Enable LVDS display detection and panel-specific configuration Make I2C based LVDS detection and configuration model specific: - not all boards support LVDS connectors; fail detection that do not support LVDS to avoid misdetecting an I2C device as a display - GPIO configuration is panel specific; use panel name where needed Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: ventana: fix splash logo drawingTim Harvey4-0/+10
After mxc_ipuv3 DM_VIDEO conversion showing splash image doesn't work. Fix this by adding new requirements: - splashimage env variable. - CONFIG_SPLASH_SCREEN - CONFIG_CMD_BMP Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: ventana: enable additional USB ether devicesTim Harvey3-0/+15
Enable additional USB ethernet devices. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: ventana: remove phy gpio reset from dtTim Harvey1-0/+8
We configure network phy configuration for internal delay, LED config, and clock config. If we leave the phy reset gpio defined in dt the kernel may issue a reset to the phy and break these configs. While some may be handled by a kernel phy driver, others may not (typically LED config). Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: ventana: add U-Boot watchdog supportTim Harvey3-3/+15
Add watchdog support for U-Boot Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: ventana: add part commandTim Harvey3-0/+3
Add part command for obtaining info about disk partitions. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards ↵Frieder Schrempf21-1/+1841
(N63xx/N64xx) This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by Kontron Electronics GmbH. Currently there are the following SoM flavors (SoM-Line): * N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND * N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND * N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND And the according evaluation boards (Board-Line): * N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ... * N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ... * N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ... Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config options at compile-time. Though the differences are so minor, that for the scope of these SoMs we just use a single defconfig that is compatible with both SoCs. Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
2021-10-07imx: mx7: spl: fix CONFIG_SPL_MAX_SIZE definitionMatthias Schiffer1-6/+14
The CONFIG_SPL_MAX_SIZE definition did not account for all areas that are used by the boot ROM according to the manual, causing boot failures due to truncated SPL images when actually hitting this limit. Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
2021-10-07misc: ocotp: Allow disabling ocotp driver in SPLMichael Scott2-1/+10
This allows removal of the OCOTP driver when SPL is enabled. Disabling OCOTP reduces SPL size efficiently. Signed-off-by: Michael Scott <mike@foundries.io> Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-10-07ARM: dts: imx: use generic name busOleksandr Suvorov15-27/+27
Synchronize the u-boot and kernel imx device trees, using tuned script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus") Per devicetree specification, generic names are recommended to be used, such as bus. i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node name. Script: sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-10-07mx7ulp: Update wdog disable sequenceYe Li1-8/+25
Update the mx7ulp wdog disable sequence to avoid potential reset issue in unlock or refresh sequence. Both sequence need two words write to wdog CNT register in 16 bus clocks window, if miss the window, the write will cause violation in wdog and reset the chip. Current u-boot code is using writel() function which has a DMB barrier to order the memory access. The DMB between two words write may introduce some delay in certain circumstance, causing the wdog reset due to 16 bus clock window requirement. Also, WDOG1 might have been enabled already depending on FUSE hence we need to be as close as possible to its reconfiguration timing requirement of 128 bus clock limit. This patch replaces writel() function by __raw_writel() to avoid such issue, and improve to check if watchdog is already disabled or unlocked. Signed-off-by: Ye Li <ye.li@nxp.com> Co-developed-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io> Co-developed-by: Ricardo Salveti <ricardo@foundries.io> Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2021-10-07rtc: rv8803: add epson,rx8803 and epson,rx8900 compatibleHeiko Thiery1-0/+2
The RX8803 and RX8900 register layouts are compatible with the one of the RV8803. So add these to the compatibles. The same compatible strings are used and approved in linux kernel. Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Michael Walle <michael@walle.cc>
2021-10-07ARM: dts: imx6-apalis: enable watchdogRicardo Salveti1-0/+11
Add u-boot.dtsi specific to imx6-apalis with a watchdog enabled. If OP-TEE is loaded by SPL, it may use a watchdog to handle fails of u-boot running. Enable the watchdog in SPL to use it by OP-TEE. Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2021-10-07ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-IDMarek Vasut1-1/+1
Since c6df0e2ffdc ("net: phy: micrel: add support for DLL setup on ksz9131") the Micrel PHY driver correctly configures the delay register. The Verdin PHY is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-10-07imx8qm_mek: Increase CONFIG_SYS_BOOTM_LEN to 64MBOleksandr Suvorov1-0/+2
The BSP platform LmP supports the board NXP iMX8QM MEK. The kernel size in LmP exceeds 32Mb. Increase the maximum size of an uncompressed kernel to fix the following error: Uncompressing Kernel Image Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN Must RESET board to recover Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2021-10-07imx8mq_evk: Increase CONFIG_SYS_BOOTM_LEN to 64MBOleksandr Suvorov1-1/+1
The BSP platform LmP supports the board NXP iMX8M Plus EVK. The kernel size in LmP exceeds 32Mb. Increase the maximum size of an uncompressed kernel to fix the following error: Uncompressing Kernel Image Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN Must RESET board to recover Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2021-10-07imx8mm_evk: Increase CONFIG_SYS_BOOTM_LEN to 64MBOleksandr Suvorov1-1/+1
The BSP platform LmP supports the board NXP iMX8M Mini EVK. The kernel size in LmP exceeds 32Mb. Increase the maximum size of an uncompressed kernel to fix the following error: Uncompressing Kernel Image Error: inflate() returned -5 Image too large: increase CONFIG_SYS_BOOTM_LEN Must RESET board to recover Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2021-10-07Kconfig: Don't use RSA_FREESCALE_EXP on MX7ULPRicardo Salveti1-2/+2
The CAAM on IMX7ULP doesn't support public key hardware acceleration (PKHA), as in other NXP parts. Disable RSA_FREESCALE_EXP for IMX7ULP too. Fixed: f4e9ff7135 ("Kconfig: Don't use RSA_FREESCALE_EXP on IMX") Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
2021-10-07arm: dts: imx8mp: Generate single bootable binaryTeresa Remmet4-4/+20
binman conversion made flashing flash.bin and u-boot.itb necessary. Update binman config to create a single flash.bin image again. This updates imx8mp_evk and phyCORE-i.MX8MP as they share the same binman config. Updated also imx8mp_evk documentation. Tested on phyCORE-i.MX8MP. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-10-07arm: imx8m: imx8mm-cl-iot-gate: Add support for detect memory sizeYing-Chun Liu (PaulLiu)1-0/+25
When purchasing imx8mm-cl-iot-gate it is able to customize the memory size. It could be 1GB, 2GB and 4GB. We implement board_phys_sdram_size() to detect the memory size for usage. Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org> Cc: Fabio Estevam <festevam@denx.de> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
2021-10-07tree: imx: remove old fit generator scriptAndrey Zhizhikin2-146/+0
Since derivatives are moving to binman from usage of the FIT generator script, and considering the warning introduced in f4a43d2925 ("Makefile: Warn against using CONFIG_SPL_FIT_GENERATOR"), usage of FIT generator is discouraged. Current FIT generator also generates broken output, since commit 3f04db891a ("image: Check for unit addresses in FITs") prohibits using '@' for unit addresses but the generator script still emits the old sematics. Remove the generator script and corresponding call in Makefile, all derivatives should be migrated to binman in order to provide binary images. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-07imx8mm-cl-iot-gate: Split the defconfigsFabio Estevam8-14/+420
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot binary due to the lack of fip.bin: " BINMAN all Image 'main-section' is missing external blobs and is non-functional: blob-ext Some images are invalid" To make the build process more consistent with the other i.MX8M targets, split the defconfig in two: - imx8mm-cl-iot-gate_defconfig: standard defconfig that only requires ATF / DDR firmware. - imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that requires ATF / Optee / mbedtls / DDR firmware. Signed-off-by: Fabio Estevam <festevam@denx.de> Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
2021-10-07mx7ulp: Allow to enable CONFIG_IMX_HABRicardo Salveti1-1/+1
Secure boot support on mx7ulp was added in the commit 27117b2024b6 ("mx7ulp: Add HAB boot support"). Allow selecting CONFIG_IMX_HAB for ARCH_IMX7ULP. Fixes: 27117b2024b6 ("mx7ulp: Add HAB boot support") Signed-off-by: Ricardo Salveti <ricardo@foundries.io> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-07imx8m: Restrict usable memory based on rom_pointer[0]Ying-Chun Liu (PaulLiu)1-3/+13
When TEE is loaded, we need to restrict the memory usage based on rom_pointer[0] Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org> Cc: Fabio Estevam <festevam@denx.de> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: uboot-imx <uboot-imx@nxp.com> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2021-10-07arm: dts: imx8mm-venice*: remove thermal zone overridesTim Harvey2-24/+0
Remove the unnecessary thermal zone overrides. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07board: gateworks: venice: update thermal temp thresholds per cpu gradeTim Harvey1-0/+18
Update the passive/critical thermal zone dt config per CPU temperature grade. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07arm: dts: imx8mm-venice-gw700x: fix mp5416 pmic configTim Harvey1-19/+37
Fix various MP5416 PMIC configurations: - Update regulator names per dt-bindings - ensure values fit among valid register values - add required regulator-max-microamp property - add regulator-always-on prop Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07board: gateworks: venice: do not overwrite serial#Tim Harvey1-1/+2
Do not overwrite existing serial# env to avoid: ## Error: Can't overwrite "serial#" ## Error inserting "serial#" variable, errno=1 Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07board: gateworks: venice: display hwmon details by defaultTim Harvey1-0/+3
Display hwmon values by default when using the 'gsc' command. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-07imx53: usbarmory: Add card detect configurationAndrej Rosano1-0/+1
After the enforcement of DM_MMC the microSD card is not detected. Fix by correctly configuring the card detect in the devicetree. Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
2021-10-07mtd: nand: mxs_nand_spl: Add nand_spl_adjust_offsetYe Li1-0/+6
Since the mxs_nand_spl has implemented adjust read offset in nand_spl_load_image, so we don't need to check the bad block in nand_spl_adjust_offset. Directly return the offset to continue read by nand_spl_load_image. Signed-off-by: Ye Li <ye.li@nxp.com>
2021-10-07arm: imx8m: Fix pad DSE issue for i.MX8MM/MN/MPYe Li1-9/+12
According to 8MM/MN/MP reference manual, their pad registers only have 4 valid DSE values. And DSE2 and DSE4 are different with current definitions in iomux-v3.h. Fix the issue to align with manual. Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2021-10-07mmc: fsl_esdhc_imx: Fix clock disable issueYe Li1-1/+1
The SD clock disable is wrapped by MMC_SUPPORTS_TUNING. So it only works when UHS is enabled. However, in SD initialization the power cycle does not depends on UHS. But the power cycle needs disable the SD clock before power down. So this causes a problem when UHS is not enabled. Some cards can't become ready (ACMD14 timeout) due to the clock is enabled during power cycle. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-10-07imx: spl: fix imx8m secure bootHeiko Schocher2-1/+20
cherry-picked from NXP code: 719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu") which fixes secure boot on imx8m based boards. Problem was that FIT header and so IVT header too, was loaded to memallocated address. So the ivt header address coded in IVT itself does not fit with the real position. Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tim Harvey <tharvey@gateworks.com>
2021-10-07imx: spl: implement spl_load_simple_fit_fix_loadHeiko Schocher1-0/+33
read the address where the IVT header must sit from IVT image header, loaded from SPL into an malloced buffer and copy the IVT header to this address May make this dependend on SoC ? Signed-off-by: Heiko Schocher <hs@denx.de>
2021-10-07spl_fit. add hook to make fixes after fit header is loadedHeiko Schocher2-0/+19
add hook function spl_load_simple_fit_fix_load() which is called after fit image header is loaded. Signed-off-by: Heiko Schocher <hs@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2021-10-07mtd: nand: Fix typo in MXC Kconfig symbol descriptionHaolin Li1-1/+1
Trivial typo fix. Signed-off-by: Haolin Li <li.haolin@qq.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com>
generated by cgit v1.1 at 2024-09-06 20:01:03 +0000