aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2012-04-16tricorder: Add UBIFSBernhard Walle1-2/+4
Since kernel should be in a ubifs partition, we need UBIFS. The greater malloc size is needed for UBIFS. Signed-off-by: Bernhard Walle <walle@corscience.de> Squashed two commits (UBIFS enabled and malloc size increased) into one. Signed-off-by: Thomas Weber <weber@corscience.de>
2012-04-16cm-t35: fix Ethernet reset timingIgor Grinberg1-5/+6
The reset_net_chip() function has wrong timings for the reset pulse. This appeared to work until: 0607e2b (ARMV7: OMAP: Write more than 1 byte at a time in i2c_write) Fix the Ethernet support by introducing right timings. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-04-16hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORTTom Rini1-0/+1
With older toolchains we need CONFIG_SPL_LIBGENERIC_SUPPORT in order for CONFIG_SPL_NAND_SUPPORT to link. Signed-off-by: Tom Rini <trini@ti.com>
2012-04-16BeagleBoard: Remove userbutton command and use gpio command insteadJoel Fernandes2-57/+9
Remove userbutton command and do the detection in board config file using the gpio command Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com> Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2012-04-16OMAP: Move omap1510inn to Unmaintained / OrphanedTom Rini1-4/+3
After removing omap1610inn for not building, move omap1510inn to orphaned. Also update boards.cfg to note it's part of the 'omap' SoC to make sure the board is built more often and future breakage noticed quicker. Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Tom Rini <trini@ti.com>
2012-04-09Merge branch 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-stagingWolfgang Denk6-10/+35
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging: LMB: Fix undefined lmb_reserve() on non-lmb platforms MIPS: fix endianess handling MIPS: fix inconsistency in config option for cache operation mode MIPS: board.c: fix init of flash data in bd_info
2012-04-09Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk19-51/+2025
* 'master' of git://git.denx.de/u-boot-net: net/designware: Change timeout loop implementation net/designware: Set ANAR to 0x1e1 net/designware: Program phy registers when auto-negotiation is ON net/designware: Try configuring phy on each dw_eth_init net/designware: Consecutive writes must have delay net/designware: Phy address fix net/designware: Fix the max frame length size net/designware: Fix to restore hw mac address microblaze: Wire up LL_TEMAC driver initialization microblaze: Add faked LL_TEMAC driver configuration microblaze: Enable several ethernet driver compilation net: ll_temac: Add LL TEMAC driver to u-boot Update net subsystem maintainer in doc/git-mailrc net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back mvgbe: remove warning for unused methods
2012-04-09Merge branch 'master' of git://git.denx.de/u-boot-onenandWolfgang Denk7-23/+86
* 'master' of git://git.denx.de/u-boot-onenand: onenand: samsung: Enable OneNAND support at Samsung's Exynos4210 onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB() onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210 onenand:samsung Target dependent OneNAND chip probe function
2012-04-09Merge branch 'master' of git://git.denx.de/u-boot-niosWolfgang Denk3-1/+33
* 'master' of git://git.denx.de/u-boot-nios: nios2 - adjust gbl data off to account for bd_info nios2: implement get_ticks and get_tbclk nios2: add flush_dcache_range function
2012-04-09Merge branch 'master' of git://git.denx.de/u-boot-x86Wolfgang Denk1-5/+0
* 'master' of git://git.denx.de/u-boot-x86: x86: Remove dead code in eNET
2012-04-09LMB: Fix undefined lmb_reserve() on non-lmb platformsMarek Vasut1-0/+1
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-04net/designware: Change timeout loop implementationAmit Virdi1-16/+38
The new implementation changes the timeout loop implementation to avoid 1 ms delay in each failing test. It also configures the delay to 10usec. Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Set ANAR to 0x1e1Armando Visconti1-0/+3
This patch forces the advertised capabilities during auto negotiation to always be 10/100 Mbps and half/full as duplexing. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Program phy registers when auto-negotiation is ONVikas Manocha1-14/+29
If AN(auto-negotiation) is ON, speed bit of control register are not applicable. Also phy registers were not getting programmed as per the result of AN. This patch sets only AN bit & restart AN bit for AN ON selection & programs PHY registers as per AN result. Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Try configuring phy on each dw_eth_initVipin Kumar2-21/+30
Phy autonegotiation works only when the ethernet cable is plugged in. Since the phy was configured only at the init time, a plugged in cable was necessary to initialize the phy properly. This patch keeps a flag to check if the phy initialization has succeeded, and calls configure_phy routine at every init if this flag reports otherwise. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Consecutive writes must have delayArmando Visconti1-2/+1
This patch solves a TX/RX problem which happens at 10Mbps, due to the fact that we are not respecting 4 cyles of the phy_clk (2.5MHz) between two consecutive writes on the same register. Signed-off-by: Armando Visconti <armando.visconti@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Phy address fixVipin KUMAR1-1/+1
The code assumes the phy address to be > 0, which is not true, the phy address can be in the range 0-31. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Fix the max frame length sizeVipin KUMAR1-1/+1
The max frame length for normal descriptor can be 0x7FF i.e 2047. It was wrongly specified as 2048. Currently, the max descriptor length is around 1500, so redefining the mask to 1600 Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04net/designware: Fix to restore hw mac addressVipin KUMAR1-1/+6
The network controller mac resets hardware address stored in MAC_HI and MAC_LO registers if mac is resetted. So, hw mac address needs to be restored in case mac is explicitly resetted from driver. Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-04onenand: samsung: Enable OneNAND support at Samsung's Exynos4210Lukasz Majewski1-0/+1
Enable OneNAND support for Exynos4210 (C210 universal). Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-04-04onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()Lukasz Majewski2-16/+33
This replacement causes 4KB page size devices to work properly with u-boot. The old ONENAND_IS_MLC() behavior has been preserved by explicit setting of ONENAND_HAS_4KB_PAGE for those devices. This change makes the onenand_base.c file more resembling the respective kernel sources. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> --- Test HW: - Samsung S5PC110 GONI - Samsung S5PC210 Universal
2012-04-04microblaze: Wire up LL_TEMAC driver initializationStephan Linz1-0/+36
Initialize ll_temac driver. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04microblaze: Add faked LL_TEMAC driver configurationStephan Linz2-4/+14
Expand the specific configuration for the microblaze-generic board in xparameters.h with a faked setup to enable the LL_TEMAC driver. Note: From now the microblaze-generic board is no longer a valid board configuration for a real piece of hardware. Rather than, we use the file config.mk and xparameters.h as a faked board configuration to force the compilation of all potential driver code for Microblaze systems. Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04microblaze: Enable several ethernet driver compilationStephan Linz1-5/+6
U-Boot's multipple network supports enables to use several ethernet drivers but microblaze-generic platform config file select only one driver. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04net: ll_temac: Add LL TEMAC driver to u-bootStephan Linz10-0/+1872
Xilinx LocalLink Tri-Mode Ether MAC driver can be used by Xilinx Microblaze or Xilinx ppc405/440 in SDMA and FIFO mode. DCR or XPS bus can be used. The driver uses and requires MII and PHYLIB. CP: 4 warnings: 'Use of volatile is usually wrong' I won't fix this, because it depends on the network driver subsystem. Reported-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04onenand:samsung OneNAND chip probe functions added for GONI and Exynos4210Lukasz Majewski2-0/+3
Separate callback for probing OneNAND memory chip. Tested at: Samsung S5PC110 GONI Samsung Exynos4210 (S5PC210 Universal) Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com>
2012-04-04onenand:samsung Target dependent OneNAND chip probe functionLukasz Majewski4-7/+49
Separate callback for probing OneNAND memory chip. If no special function is defined, default implementation will be used. This approach gives more flexibility for OneNAND device probing. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2012-04-03Update net subsystem maintainer in doc/git-mailrcJoe Hershberger1-1/+2
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com>
2012-04-03net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall backEric Miao1-2/+1
Ignore the return value of eth_getenv_enetaddr_by_index(), and if it fails, fall back to use dev->enetaddr, which could be filled up by the ethernet device driver: With the current code, introduced with below commit, eth_write_hwaddr() will fail immediately if there is no eth<n>addr in the environment variables. However, e.g. for an overo based product that uses the SMSC911x ethernet chip (with the MAC address set via EEPROM connected to the SMSC911x chip), the MAC address is still OK. On mx28 boards that are depending on the OCOTP bits to set the MAC address (like the Denx m28 board), the OCOTP bits should be used instead of failing on the environment variables. Actually, this was the original behavior, and was later changed by commit 7616e7850804c7c69e0a22c179dfcba9e8f3f587. Signed-off-by: Eric Miao <eric.miao@linaro.org> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Dirk Behme <dirk.behme@de.bosch.com> CC: Stefan Roese <sr@denx.de> CC: Eric Miao <eric.miao@linaro.org> CC: Wolfgang Denk <wd@denx.de> CC: Philip Balister <philip@balister.org> CC: Zach Sadecki <zach@itwatchdogs.com>
2012-04-03mvgbe: remove warning for unused methodsStefan Bigler1-0/+2
Some baords may use the GBE interface but they have no phy connected to the interface and a direct MAC/MAC interface. For them we need to get rid of compiler warnings. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2012-04-02LMB: Fix undefined lmb_reserve() on non-lmb platformsMarek Vasut1-0/+1
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: Graeme Russ <graeme.russ@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2012-04-02MIPS: fix endianess handlingDaniel Schwierzeck4-7/+24
Make endianess of target CPU configurable. Use the new config option for dbau1550_el and pb1000 boards. Adapt linking of standalone applications to pass through endianess options to LD. Build tested with: - ELDK 4 mips_4KC- and mips4KCle - Sourcery CodeBench Lite 2011.03-93 With this patch all 26 MIPS boards can be compiled now in one step by running "MAKEALL -a mips". Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-04-02MIPS: fix inconsistency in config option for cache operation modeDaniel Schwierzeck1-1/+5
Commit ab2a98b11716364bc5a8c43cdfa7fee176cda1d8 missed to use the new config option in dcache_enable(). Fix this to avoid inconsistencies if someone wants to disable and enable D-caches. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-04-02MIPS: board.c: fix init of flash data in bd_infoDaniel Schwierzeck1-2/+6
Boards with CONFIG_SYS_NO_FLASH should not forced to define CONFIG_SYS_FLASH_BASE. In this case the flash data in bd_info should be initialized with 0 like the other archs do. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
2012-04-01x86: Remove dead code in eNETSimon Glass1-5/+0
This avoids a compiler warning about unused variables. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-By: Graeme Russ <graeme.russ@gmail.com>
2012-03-31Prepare v2012.04-rc1v2012.04-rc1Wolfgang Denk1-3/+3
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-03-30net/altera_tse: use flush_dcache_range instead of flush_dcacheStefan Kristiansson1-3/+6
flush_dcache is not declared in the common.h API, flush_dcache_range however is Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
2012-03-30net/ethoc: use flush_dcache_range instead of flush_dcacheStefan Kristiansson1-3/+3
flush_dcache is not declared in the common.h API, flush_dcache_range however is Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Thomas Chou <thomas@wytron.com.tw> Acked-by: Thomas Chou <thomas@wytron.com.tw>
2012-03-30Merge branch 'master' of git://git.denx.de/u-boot-usbWolfgang Denk7-7/+116
* 'master' of git://git.denx.de/u-boot-usb: Enable high speed support for USB device framework and usbtty
2012-03-30RAMDISK: Fix unused variable issue caused by raw rd supportMarek Vasut1-0/+2
image.c: In function ‘boot_get_ramdisk’: image.c:800:8: warning: unused variable ‘end’ [-Wunused-variable] Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2012-03-30BOOT: Add RAW ramdisk support to bootzMarek Vasut3-5/+21
This patch allows loading RAW ramdisk via bootz command. The raw ramdisk is loaded only in case it's size is specified: bootz <kernel addr> <ramdisk addr>:<ramdisk size> <fdt addr> For example: bootz 0x42000000 0x43000000:0x12345 0x44000000 Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Rob Herring <rob.herring@calxeda.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com Cc: Simon Glass <sjg@chromium.org> Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2012-03-30BOOT: Add "bootz" command to boot Linux zImage on ARMMarek Vasut4-9/+171
This command boots Linux zImage from where the zImage is loaded to. Passing initrd and fdt is supported. Tested on i.MX28 based DENX M28EVK Tested on PXA270 based Voipac PXA270. NOTE: This currently only supports ARM, but other architectures can be easily added by defining bootz_setup(). Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Tom Warren <TWarren@nvidia.com> Cc: albert.u.boot@aribaud.net Cc: afleming@gmail.com, Cc: Simon Glass <sjg@chromium.org>, Cc: Stephen Warren <swarren@nvidia.com> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2012-03-30mx28evk: fix build errorAnatolij Gustschin1-0/+5
Fix: drivers/mmc/libmmc.o: In function `mxsmmc_send_cmd': /home/ag/git/u-boot/drivers/mmc/mxsmmc.c:210: undefined reference to `mxs_dma_desc_append' /home/ag/git/u-boot/drivers/mmc/mxsmmc.c:211: undefined reference to `mxs_dma_go' drivers/mmc/libmmc.o: In function `mxsmmc_initialize': /home/ag/git/u-boot/drivers/mmc/mxsmmc.c:306: undefined reference to `mxs_dma_desc_alloc' Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-03-30pci: declare pciauto functions in headerLinus Walleij2-6/+5
The FSL PCI driver uses local prototypes for pciauto_[pre|post]scan_setup_bridge(), this does not seem right, so move them to the <pci.h> file. Fixed a small extern declaration too, this is harmless but distracts the view since all other prototypes are explicitly external. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-30pci: get rid of local prototypesLinus Walleij2-8/+0
two boards were redeclaring pciauto_region_allocate() in their local scope for no obvious reason, the function is in <pci.h> anyway, this is probably just copying artifacts and old cruft. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-03-30Add support for loading and saving the environment to a FAT partitionMaximilian Schwerin3-1/+159
The following must be defined: CONFIG_ENV_IS_IN_FAT Enable this saving environment to FAT. FAT_ENV_INTERFACE Interface the FAT resides on (e.g. mmc). FAT_ENV_DEVICE The interface device number (e.g. 0 for mmc0) FAT_ENV_PART The device part (e.g. 1 for mmc0:1) FAT_ENV_FILE The filename of the environment file. Author: Maximilian Schwerin <mvs@tigris.de> Removed dead DEBUG comment. Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-03-30MAKEALL: Add -m/-M option to determine maintainersMarek Vasut1-3/+112
The -m option tries to find the board in MAINTAINERS file and figure out the email. The -M option lists boards including their maintainers emails and all affiliated emails. There are multiple strategies used to retrieve these emails: 1) Check board/<boardname> with git log and use three most recent emails 2) Check board/<boardname> with git log and use three most used emails 3) Try finding board in MAINTAINERS file and retrieve all emails from there The result is then sorted and unique results are retrieved and reported. For -m option, only strategy 3) is used. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Wolfgang Denk <wd@denx.de>
2012-03-30cmd_log: print log->v2.con value in the "log info" commandHeiko Schocher1-0/+1
print in the "log info" command, if "log_version = 2" also the value from "log->v2.con". Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
2012-03-30command, log: Coding Style cleanupHeiko Schocher1-45/+51
Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de>
2012-03-30command, log: print with "log show" a full logbufferHeiko Schocher1-1/+3
If the logbuffer contains LOGBUFF_LEN chars, they never got printed with the "log show" command, because chars get printed with the following for loop: for (i = 0; i < (size & LOGBUFF_MASK); i++) { with size = LOGBUFF_LEN and LOGBUFF_MASK = (LOGBUFF_LEN-1) for loop never executed ... Fix this. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Fixed merge conflict. Signed-off-by: Wolfgang Denk <wd@denx.de>
generated by cgit v1.1 at 2024-09-16 13:18:56 +0000