aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)AuthorFilesLines
2019-08-23rockchip: rk3368: defconfig: remove SPL raw image supportKever Yang1-0/+1
RK3368 SPL only support FIT image for ATF bl31. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: rk3328: defconfig: remove SPL raw image supportKever Yang2-0/+2
RK3328 SPL only support FIT image for ATF bl31. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: Move config SYS_MALLOC_LEN to KconfigKever Yang10-10/+2
Use Kconfig for option SYS_MALLOC_LEN and default to 0x2000000. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: dts: rk3328-rock64: fix usb power supplyKever Yang1-21/+2
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct power supply for USB HOST ports. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: rk3328: migrate u-boot node to -u-boot.dtsiKever Yang5-85/+66
Move all the nodes only shown in u-boot to -u-boot.dtsi to make rk3328.dtsi clean. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: dts: rk3328-rock64: enable usb3 xhci controllerKever Yang1-0/+4
Rock64 has a USB3.0 port, enable the controller so that we can use it. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23rockchip: clk: rk3328: add clk_enable ops for HCLK_HOST0Kever Yang1-0/+12
Required to successfully probe the ehci generic driver Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-23ram: rk3399: update cap and ddrconfig for each channel after initKever Yang1-78/+81
We need to store all the ram related cap/map info back to register for each channel after all the init has been done in case some of register was reset during the process. Signed-off-by: YouMin Chen <cym@rock-chips.com> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-08-22Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini70-196/+1533
- i2c dm model support of lx2160a, ls1088a, lx2088a, ls1028a - icid setup for ls1028a, ls1088a - other small fixes
2019-08-22armv8: ls1028a: add icid setup for platform devicesLaurentiu Tudor8-16/+76
Add ICID setup for the platform devices contained on this chip: usb, sata, sdhc, edma, qdma, gpu, display and sec. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1088a: add icid setup for platform devicesLaurentiu Tudor6-10/+89
Add ICID setup for the platform devices contained on this chip: usb, sata, sdhc, sec. The ICID macros for SEC needed to be adapted because the format of the registers is different. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: fsl-layerscape: make icid setup endianness awareLaurentiu Tudor2-11/+28
The current implementation assumes that the registers holding the ICIDs are universally big endian. That's no longer the case on newer platforms so update the code to take into account the endianness of each register. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: fsl-layerscape: add base addresses for several devicesLaurentiu Tudor1-0/+15
Add CCSR base addresses for ESDHC2, EDMA QDMA, DISPLAY and GPU devices. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: fsl-layerscape: add missing sec jr base address definesLaurentiu Tudor1-0/+8
Add defines for all the SEC job rings base addresses. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: kconfig: Fix some platforms incorrect I2C clock dividerChuanhua Han1-0/+4
By default, i2c input clock is platform clk / 2, but some of the platform of i2c clock divider does not meet this kind of circumstance, so alone to set default values for these platforms. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1088aqds: support DSPI mode by hwconfigChuanhua Han3-0/+39
BRDCFG4[USBOSC] and BRDCFG5[SPR] register field of Qixis device is used to control SPI and other IP signal routing. USBOSC: 0= SPI_CLK used as external USB REFCLK input driven with 24.000 MHz. SPI devices are unusable in this mode. 1= SPI_CLK used as SPI clock. SPI devices are usable in this mode. USB block is clocked from internal sources SPR[3:2]: SPI_CS / SDHC_DAT4:7 Routing (schematic net CFG_SPI_ROUTE[3:2]): 00= SDHC/eMMC 8-bit 01= SD Card Rev 2.0/3.0 10= SPI on-board memory 11= TDM Riser / SPI off-board connector. The default value is 00 if an SDCard/eMMC card is selected as the boot device. SPR[1:0]: SPI_SIN/SOUT/SCK Routing (schematic net CFG_SPI_ROUTE[1:0]): 00= SDHC Sync loop 01= TDM Riser / SPI off-board connector. 10= SPI on-board memory. 11= SPI off-board connector. By default, the SPI feature is not available, so we need to configure the above register fields to select the route to the SPI feature. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1028aqds: define ARCH_MISC_INIT to handle muxPankaj Bansal1-0/+1
Define ARCH_MISC_INIT for LS1028AQDS platform to handle board related mux. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1046afrwy: Define CONFIG_ENV_ADDR for QSPI BootAlison Wang1-0/+3
Defines CONFIG_ENV_ADDR for QSPI Boot which specifies the start address of the flash sector containing the environment. It fixes the issue that bootcmd is always set as default at bootup. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: fsl: lx2160ardb: enable flexcanPankaj Bansal1-0/+20
Flexcan in LX2160ARDB is controlled by FPGA register boardcfg4 bit 5. enable this bit so that flexcan is enabled in LX2160ARDB. Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: ls1088a: Enable DM support for pcf2127 rtcChuanhua Han4-7/+31
Enable related configs on all ls1088aqds boards to support pcf2127 rtc DM function. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1088aqds : Add pcf2127 nodeChuanhua Han1-0/+23
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1088aqds: Add support of I2C driver model.Chuanhua Han2-49/+104
Udate ls1088aqds board init code to support DM_I2C. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1088ardb: Add slave nodes under the i2c0 controllerChuanhua Han1-0/+23
This patch adds some slave nodes to support the i2c dm on the device side under the i2c0 controller. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1088a: add I2C node supportChuanhua Han1-0/+32
One ls1088a, there are four I2C controllers. So add all I2C node for ls1088a in device tree. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22gpio: do not include <asm/arch/gpio.h> on ARCH_LS1088AChuanhua Han1-1/+1
As no gpio.h is defined for this architecture, to avoid compilation failure, do not include <asm/arch/gpio.h> for arch ls1088a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: ls1088a: Add support of I2C driver modelChuanhua Han3-2/+151
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the ls1088a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: ls2088a: Enable DM support for ds3231 rtcChuanhua Han4-9/+27
Enable related configs on all ls2088aqds boards to support ds3231 rtc DM function. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls2088aqds : Add ds3232 nodeChuanhua Han1-0/+19
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: ls2088aqds: Add support of I2C driver model.Chuanhua Han3-47/+121
Update ls2088aqds board init code to support DM_I2C. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22rtc: ds3232/ds3231: Add support to generate 32KHz output for driver moduleChuanhua Han5-0/+32
Add an implementation of the rtc_enable_32khz_output() that uses the driver model i2c APIs. Also put code related to rtc_enable_32khz_output under CONFIG_RTC_ENABLE_32KHZ_OUTPUT. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls2088ardb: Add slave nodes under the i2c0Chuanhua Han1-0/+22
Add some slave nodes to support the i2c dm on the device side under the i2c0. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: fsl-ls2088a: add i2c node supportchuanhua han1-0/+36
One ls2088a, there are four I2C controllers. So add I2C nodes in dts for ls2088a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22gpio: do not include <asm/arch/gpio.h> on ARCH_LS2080AChuanhua Han1-1/+2
As no gpio.h is defined for this architecture, to avoid compilation failure, do not include <asm/arch/gpio.h> for arch ls2080a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: ls2088a: Add support of I2C driver model.Chuanhua Han3-0/+13
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the ls2088a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1028aqds: Add pcf2127 node under i2c1Chuanhua Han1-0/+5
Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1028aqds: Add pca9547 node under the i2c0 controllerChuanhua Han1-0/+8
Add pca9547 node to support i2c multiplexer under the i2c0 controller in dts for ls1028aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: ls1028a: Enable DM support for pcf2127 rtcChuanhua Han5-12/+36
Enable related configs on all ls1028aqds boards to support pcf2127 rtc DM function. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Tested-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: ls1028aqds: Remove the definition of CONFIG_SYS_I2C_EARLY_INITChuanhua Han1-1/+0
Since i2c uses dm mode, i2c controller will be initialized when reading and writing devices on i2c bus. So there is no need for the original non-dm mode i2c early initialization function call, this patch removed the definition of CONFIG_SYS_I2C_EARLY_INIT. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: ls1028ardb: Add slave nodes under the i2c0 controllerChuanhua Han1-0/+20
Add some slave nodes to support the i2c dm on the device side under the i2c0. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22gpio: do not include <asm/arch/gpio.h> on ARCH_LS1028AChuanhua Han1-1/+1
As no gpio.h is defined for this architecture, to avoid compilation failure, do not include <asm/arch/gpio.h> for arch ls1028a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: ls1028a: Add support of I2C driver modelChuanhua Han3-1/+10
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used.When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the ls1028a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: lx2160: enable DM support for pcf2127 rtcChuanhua Han5-8/+32
Enable related configs on all lx2160ardb boards to support pcf2127 rtc DM feature. Also remove SYS_I2C_MXC_I2Cx, where x is from 1 to 8 from Kconfig. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: lx2160aqds : Add pcf2127 nodeChuanhua Han1-0/+23
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 in dts for lx2160aqds boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: lx2160ardb : Add the "u-boot, dm-pre-reloc" for i2c0Chuanhua Han1-0/+5
Lx2160ardb need to use i2c0 before relocation, so we also need to set u-boot, dm-pre-reloc to initialize node before relocation. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: Add pcf2127 node for lx2160ardbChuanhua Han1-0/+9
Adds the pcf2127-rtc node under the i2c4 node dts of lx2160ardb boards. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22armv8: dts: fsl-lx2160a: add i2c controller and gpio DT nodesChuanhua Han1-0/+85
In lx2160a soc, there are eight i2c controllers, this patch adds i2c nodes for lx2160a, and the gpio2 nodes on which the i2c4 controller depends. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22gpio: do not include <asm/arch/gpio.h> on ARCH_LX2160AChuanhua Han1-1/+2
As no gpio.h is defined for this architecture, to avoid compilation failure, do not include <asm/arch/gpio.h> for arch ls2160a. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22drivers: i2c: mxc: Fix compiler error when using i2c dm modeChuanhua Han2-7/+10
I2C dm mode enablemenet causes below compilation errors: In file included from include/config.h:8:0, from include/common.h:20: include/config_fallbacks.h:51:4: error: #error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" # error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" ^~~~~ In file included from include/config.h:8:0, from include/common.h:20: include/config_fallbacks.h:51:4: error: #error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" # error "Cannot define CONFIG_SYS_I2C when CONFIG_DM_I2C is used" ^~~~~ board/freescale/lx2160a/lx2160a.c: In function 'board_early_init_f': board/freescale/lx2160a/lx2160a.c:108:2: warning: implicit declaration of function 'i2c_early_init_f'; did you mean 'arch_early_init_r'? [-Wimplicit-function-declaration] i2c_early_init_f(); ^~~~~~~~~~~~~~~~ arch_early_init_r drivers/i2c/mxc_i2c.c: In function 'mxc_i2c_probe': drivers/i2c/mxc_i2c.c:824:8: warning: implicit declaration of function 'enable_i2c_clk'; did you mean 'enable_irq_wake'? [-Wimplicit-function-declaration] ret = enable_i2c_clk(1, bus->seq); ^~~~~~~~~~~~~~ enable_irq_wake So fix these compilation errors. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22boards: lx2160a: Add support of I2C driver modelChuanhua Han6-5/+245
DM_I2C_COMPAT is a compatibility layer that allows using the non-DM I2C API when DM_I2C is used. When DM_I2C_COMPAT is not enabled for compilation, a compilation error will be generated. This patch solves the problem that the i2c-related api of the lx2160a platform does not support dm. Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22configs: ls1043aqds: Move CONFIG_FSL_QSPI to defconfigAshish Kumar4-1/+6
Move CONFIG_FSL_QSPI from header file to defconfigs, consequently unset imply config(CONFIG_SPI_FLASH_BAR) which is not valid for LS series. Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
generated by cgit v1.1 at 2024-09-15 23:15:05 +0000