diff options
Diffstat (limited to 'include/configs/cobra5272.h')
-rw-r--r-- | include/configs/cobra5272.h | 48 |
1 files changed, 24 insertions, 24 deletions
diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h index 65b9074..01828ea 100644 --- a/include/configs/cobra5272.h +++ b/include/configs/cobra5272.h @@ -29,18 +29,18 @@ * --- */ -#define CONFIG_SYS_CLK 66000000 +#define CFG_SYS_CLK 66000000 #define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ /* --- * Define baudrate for UART1 (console output, tftp, ...) * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud - * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command + * CFG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command * interface * --- */ -#define CONFIG_SYS_UART_PORT (0) +#define CFG_SYS_UART_PORT (0) /* --- * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change @@ -133,21 +133,21 @@ enter a valid image address in flash */ * --- */ -#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ +#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */ /* --- * System Conf. Reg. & System Protection Reg. * --- */ -#define CONFIG_SYS_SCR 0x0003 -#define CONFIG_SYS_SPR 0xffff +#define CFG_SYS_SCR 0x0003 +#define CFG_SYS_SPR 0xffff /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in internal SRAM) */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ +#define CFG_SYS_INIT_RAM_ADDR 0x20000000 +#define CFG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration @@ -168,28 +168,28 @@ enter a valid image address in flash */ *----------------------------------------------------------------------- */ -#define CONFIG_SYS_FLASH_BASE 0xffe00000 +#define CFG_SYS_FLASH_BASE 0xffe00000 /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization ?? */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CFG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * Cache Configuration */ -#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 8) -#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - 4) -#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) -#define CONFIG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \ +#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ + CFG_SYS_INIT_RAM_SIZE - 8) +#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \ + CFG_SYS_INIT_RAM_SIZE - 4) +#define CFG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) +#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \ CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \ CF_ACR_EN | CF_ACR_SM_ALL) -#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ +#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ CF_CACR_DISD | CF_CACR_INVI | \ CF_CACR_CEIB | CF_CACR_DCM | \ CF_CACR_EUSP) @@ -209,15 +209,15 @@ enter a valid image address in flash */ /*----------------------------------------------------------------------- * Port configuration (GPIO) */ -#define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external +#define CFG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external GPIO*/ -#define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs +#define CFG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs (1^=output, 0^=input) */ -#define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ -#define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART +#define CFG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ +#define CFG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART configuration */ -#define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ -#define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ -#define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ +#define CFG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ +#define CFG_SYS_PBDAT 0x0000 /* PortB value reg. */ +#define CFG_SYS_PDCNT 0x00000000 /* PortD control reg. */ #endif /* _CONFIG_COBRA5272_H */ |