diff options
Diffstat (limited to 'drivers/video/Kconfig')
-rw-r--r-- | drivers/video/Kconfig | 129 |
1 files changed, 10 insertions, 119 deletions
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig index 1bf7f4a..965b587 100644 --- a/drivers/video/Kconfig +++ b/drivers/video/Kconfig @@ -430,6 +430,14 @@ config ATMEL_LCD_BGR555 help Use the BGR555 output mode. Otherwise RGB565 is used. +config VIDEO_BCM2835 + bool "Display support for BCM2835" + help + The graphics processor already sets up the display so this driver + simply checks the resolution and then sets up the frame buffer with + that same resolution (or as near as possible) and 32bpp depth, so + that U-Boot can access it with full colour depth. + config VIDEO_LCD_ORISETECH_OTM8009A bool "OTM8009A DSI LCD panel support" depends on DM_VIDEO @@ -610,21 +618,6 @@ config VIDEO_IVYBRIDGE_IGD a special tool which configures the VGA ROM, but the graphics resolution can be selected in U-Boot. -config VIDEO_FSL_DCU_FB - bool "Enable Freescale Display Control Unit" - depends on VIDEO || DM_VIDEO - help - This enables support for Freescale Display Control Unit (DCU4) - module found on Freescale Vybrid and QorIQ family of SoCs. - -config VIDEO_FSL_DCU_MAX_FB_SIZE_MB - int "Freescale DCU framebuffer size" - depends on VIDEO_FSL_DCU_FB - default 4194304 - help - Set maximum framebuffer size to be used for Freescale Display - Controller Unit (DCU4). - source "drivers/video/rockchip/Kconfig" config VIDEO_ARM_MALIDP @@ -708,89 +701,9 @@ config VIDEO model. Video drivers typically provide a colour text console and cursor. -config CFB_CONSOLE - bool "Enable colour frame buffer console" - depends on VIDEO || ARCH_OMAP2PLUS - default y if VIDEO - help - Enables the colour frame buffer driver. This supports colour - output on a bitmap display from an in-memory frame buffer. - Several colour devices are supported along with various options to - adjust the supported features. The driver is implemented in - cfb_console.c - - The following defines are needed (cf. smiLynxEM, i8042) - VIDEO_FB_LITTLE_ENDIAN graphic memory organisation - (default big endian) - VIDEO_HW_RECTFILL graphic chip supports - rectangle fill (cf. smiLynxEM) - VIDEO_HW_BITBLT graphic chip supports - bit-blit (cf. smiLynxEM) - VIDEO_VISIBLE_COLS visible pixel columns (cols=pitch) - VIDEO_VISIBLE_ROWS visible pixel rows - VIDEO_PIXEL_SIZE bytes per pixel - VIDEO_DATA_FORMAT graphic data format - (0-5, cf. cfb_console.c) - VIDEO_FB_ADRS framebuffer address - VIDEO_KBD_INIT_FCT keyboard int fct (i.e. rx51_kp_init()) - VIDEO_TSTC_FCT test char fct (i.e. rx51_kp_tstc) - VIDEO_GETC_FCT get char fct (i.e. rx51_kp_getc) - CONFIG_VIDEO_LOGO display Linux logo in upper left corner - CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of linux_logo.h - for logo. Requires CONFIG_VIDEO_LOGO - CONFIG_CONSOLE_EXTRA_INFO - additional board info beside - the logo - CONFIG_HIDE_LOGO_VERSION - do not display bootloader - version string - - When CONFIG_CFB_CONSOLE is defined, the video console is the - default console. The serial console can be forced by setting the - environment 'console=serial'. - -config CFB_CONSOLE_ANSI - bool "Support ANSI escape sequences" - depends on CFB_CONSOLE - help - This allows the colour buffer frame buffer driver to support - a limited number of ANSI escape sequences (cursor control, - erase functions and limited graphics rendition control). Normal - output from U-Boot will pass through this filter. - -config VGA_AS_SINGLE_DEVICE - bool "Set the video as an output-only device" - depends on CFB_CONSOLE - default y - help - If enable the framebuffer device will be initialized as an - output-only device. The Keyboard driver will not be set up. This - may be used if you have no keyboard device, or more than one - (USB Keyboard, AT Keyboard). - -config VIDEO_SW_CURSOR - bool "Enable a software cursor" - depends on CFB_CONSOLE - default y if CFB_CONSOLE - help - This draws a cursor after the last character. No blinking is - provided. This makes it possible to see the current cursor - position when entering text on the console. It is recommended to - enable this. - -config CONSOLE_EXTRA_INFO - bool "Display additional board information" - depends on CFB_CONSOLE - help - Display additional board information strings that normally go to - the serial port. When this option is enabled, a board-specific - function video_get_info_str() is called to get the string for - each line of the display. The function should return the string, - which can be empty if there is nothing to display for that line. - config CONSOLE_SCROLL_LINES int "Number of lines to scroll the console by" - depends on CFB_CONSOLE || DM_VIDEO || LCD + depends on DM_VIDEO || LCD default 1 help When the console need to be scrolled, this is the number of @@ -798,28 +711,6 @@ config CONSOLE_SCROLL_LINES console jump but can help speed up operation when scrolling is slow. -config SYS_CONSOLE_BG_COL - hex "Background colour" - depends on CFB_CONSOLE - default 0x00 - help - Defines the background colour for the console. The value is from - 0x00 to 0xff and the meaning depends on the graphics card. - Typically, 0x00 means black and 0xff means white. Do not set - the background and foreground to the same colour or you will see - nothing. - -config SYS_CONSOLE_FG_COL - hex "Foreground colour" - depends on CFB_CONSOLE - default 0xa0 - help - Defines the foreground colour for the console. The value is from - 0x00 to 0xff and the meaning depends on the graphics card. - Typically, 0x00 means black and 0xff means white. Do not set - the background and foreground to the same colour or you will see - nothing. - config LCD bool "Enable legacy LCD support" help @@ -1017,7 +908,7 @@ config VIDEO_BMP_GZIP config VIDEO_BMP_RLE8 bool "Run length encoded BMP image (RLE8) support" - depends on DM_VIDEO || CFB_CONSOLE + depends on DM_VIDEO help If this option is set, the 8-bit RLE compressed BMP images is supported. |